Tom Rini | 83d290c | 2018-05-06 17:58:06 -0400 | [diff] [blame] | 1 | // SPDX-License-Identifier: GPL-2.0+ |
Stefan Roese | ff9c4c5 | 2016-02-12 13:48:02 +0100 | [diff] [blame] | 2 | /* |
| 3 | * Copyright (C) 2016 Stefan Roese <sr@denx.de> |
Stefan Roese | ff9c4c5 | 2016-02-12 13:48:02 +0100 | [diff] [blame] | 4 | */ |
| 5 | |
| 6 | #include <common.h> |
| 7 | #include <altera.h> |
| 8 | #include <spi.h> |
| 9 | #include <asm/io.h> |
Masahiro Yamada | 1221ce4 | 2016-09-21 11:28:55 +0900 | [diff] [blame] | 10 | #include <linux/errno.h> |
Stefan Roese | ff9c4c5 | 2016-02-12 13:48:02 +0100 | [diff] [blame] | 11 | |
| 12 | /* Write the RBF data to FPGA via SPI */ |
| 13 | static int program_write(int spi_bus, int spi_dev, const void *rbf_data, |
| 14 | unsigned long rbf_size) |
| 15 | { |
| 16 | struct spi_slave *slave; |
| 17 | int ret; |
| 18 | |
| 19 | debug("%s (%d): data=%p size=%ld\n", |
| 20 | __func__, __LINE__, rbf_data, rbf_size); |
| 21 | |
| 22 | /* FIXME: How to get the max. SPI clock and SPI mode? */ |
| 23 | slave = spi_setup_slave(spi_bus, spi_dev, 27777777, SPI_MODE_3); |
| 24 | if (!slave) |
| 25 | return -1; |
| 26 | |
| 27 | if (spi_claim_bus(slave)) |
| 28 | return -1; |
| 29 | |
| 30 | ret = spi_xfer(slave, rbf_size * 8, rbf_data, (void *)rbf_data, |
| 31 | SPI_XFER_BEGIN | SPI_XFER_END); |
| 32 | |
| 33 | spi_release_bus(slave); |
| 34 | |
| 35 | return ret; |
| 36 | } |
| 37 | |
| 38 | /* |
| 39 | * This is the interface used by FPGA driver. |
| 40 | * Return 0 for sucess, non-zero for error. |
| 41 | */ |
| 42 | int stratixv_load(Altera_desc *desc, const void *rbf_data, size_t rbf_size) |
| 43 | { |
| 44 | altera_board_specific_func *pfns = desc->iface_fns; |
| 45 | int cookie = desc->cookie; |
| 46 | int spi_bus; |
| 47 | int spi_dev; |
| 48 | int ret = 0; |
| 49 | |
| 50 | if ((u32)rbf_data & 0x3) { |
| 51 | puts("FPGA: Unaligned data, realign to 32bit boundary.\n"); |
| 52 | return -EINVAL; |
| 53 | } |
| 54 | |
| 55 | /* Run the pre configuration function if there is one */ |
| 56 | if (pfns->pre) |
| 57 | (pfns->pre)(cookie); |
| 58 | |
| 59 | /* Establish the initial state */ |
| 60 | if (pfns->config) { |
| 61 | /* De-assert nCONFIG */ |
| 62 | (pfns->config)(false, true, cookie); |
| 63 | |
| 64 | /* nConfig minimum low pulse width is 2us */ |
| 65 | udelay(200); |
| 66 | |
| 67 | /* Assert nCONFIG */ |
| 68 | (pfns->config)(true, true, cookie); |
| 69 | |
| 70 | /* nCONFIG high to first rising clock on DCLK min 1506 us */ |
| 71 | udelay(1600); |
| 72 | } |
| 73 | |
| 74 | /* Write the RBF data to FPGA */ |
| 75 | if (pfns->write) { |
| 76 | /* |
| 77 | * Use board specific data function to write bitstream |
| 78 | * into the FPGA |
| 79 | */ |
| 80 | ret = (pfns->write)(rbf_data, rbf_size, true, cookie); |
| 81 | } else { |
| 82 | /* |
| 83 | * Use common SPI functions to write bitstream into the |
| 84 | * FPGA |
| 85 | */ |
| 86 | spi_bus = COOKIE2SPI_BUS(cookie); |
| 87 | spi_dev = COOKIE2SPI_DEV(cookie); |
| 88 | ret = program_write(spi_bus, spi_dev, rbf_data, rbf_size); |
| 89 | } |
| 90 | if (ret) |
| 91 | return ret; |
| 92 | |
| 93 | /* Check done pin */ |
| 94 | if (pfns->done) { |
| 95 | ret = (pfns->done)(cookie); |
| 96 | |
| 97 | if (ret) |
| 98 | printf("Error: DONE not set (ret=%d)!\n", ret); |
| 99 | } |
| 100 | |
| 101 | return ret; |
| 102 | } |