| Caleb Connolly | e6c284b | 2023-11-20 20:48:00 +0000 | [diff] [blame^] | 1 | CONFIG_ARM=y |
| 2 | CONFIG_SKIP_LOWLEVEL_INIT=y |
| 3 | CONFIG_POSITION_INDEPENDENT=y |
| 4 | CONFIG_ARCH_SNAPDRAGON=y |
| 5 | CONFIG_DEFAULT_DEVICE_TREE="dragonboard845c" |
| 6 | CONFIG_SYS_LOAD_ADDR=0x0 |
| 7 | CONFIG_FIT=y |
| 8 | CONFIG_FIT_VERBOSE=y |
| 9 | CONFIG_BOOTSTD_FULL=y |
| 10 | # CONFIG_BOOTMETH_EXTLINUX is not set |
| 11 | # CONFIG_BOOTMETH_VBE is not set |
| 12 | # CONFIG_BOOTMETH_SCRIPT is not set |
| 13 | CONFIG_BOOTDELAY=1 |
| 14 | CONFIG_USE_PREBOOT=y |
| 15 | CONFIG_LOG_MAX_LEVEL=9 |
| 16 | CONFIG_LOG_DEFAULT_LEVEL=4 |
| 17 | # CONFIG_DISPLAY_CPUINFO is not set |
| 18 | CONFIG_DISPLAY_BOARDINFO_LATE=y |
| 19 | CONFIG_HUSH_PARSER=y |
| 20 | CONFIG_SYS_MAXARGS=64 |
| 21 | CONFIG_SYS_CBSIZE=512 |
| 22 | CONFIG_CMD_BOOTMENU=y |
| 23 | CONFIG_CMD_CLK=y |
| 24 | CONFIG_CMD_GPIO=y |
| 25 | CONFIG_CMD_MMC=y |
| 26 | CONFIG_CMD_PART=y |
| 27 | CONFIG_CMD_UFS=y |
| 28 | CONFIG_CMD_USB=y |
| 29 | CONFIG_CMD_CAT=y |
| 30 | CONFIG_CMD_BMP=y |
| 31 | CONFIG_CMD_FAT=y |
| 32 | CONFIG_CMD_FS_GENERIC=y |
| 33 | CONFIG_CMD_LOG=y |
| 34 | CONFIG_EFI_PARTITION=y |
| 35 | # CONFIG_NET is not set |
| 36 | CONFIG_CLK=y |
| 37 | CONFIG_CLK_QCOM_QCS404=y |
| 38 | CONFIG_CLK_QCOM_SDM845=y |
| 39 | CONFIG_MSM_GPIO=y |
| 40 | CONFIG_QCOM_PMIC_GPIO=y |
| 41 | CONFIG_DM_KEYBOARD=y |
| 42 | CONFIG_BUTTON_KEYBOARD=y |
| 43 | CONFIG_MMC_SDHCI=y |
| 44 | CONFIG_MMC_SDHCI_MSM=y |
| 45 | CONFIG_PHY=y |
| 46 | CONFIG_PINCTRL=y |
| 47 | CONFIG_PINCTRL_QCOM_QCS404=y |
| 48 | CONFIG_PINCTRL_QCOM_SDM845=y |
| 49 | CONFIG_DM_PMIC=y |
| 50 | CONFIG_PMIC_QCOM=y |
| 51 | CONFIG_SCSI=y |
| 52 | CONFIG_DM_SCSI=y |
| 53 | CONFIG_MSM_GENI_SERIAL=y |
| 54 | CONFIG_SPMI_MSM=y |
| 55 | CONFIG_SYSINFO=y |
| 56 | CONFIG_SYSINFO_SMBIOS=y |
| 57 | CONFIG_USB=y |
| 58 | CONFIG_USB_XHCI_HCD=y |
| 59 | CONFIG_USB_XHCI_DWC3=y |
| 60 | CONFIG_USB_DWC3=y |
| 61 | CONFIG_USB_STORAGE=y |
| 62 | CONFIG_UFS=y |
| 63 | CONFIG_VIDEO=y |
| 64 | # CONFIG_VIDEO_FONT_8X16 is not set |
| 65 | CONFIG_VIDEO_FONT_16X32=y |
| 66 | CONFIG_SYS_WHITE_ON_BLACK=y |
| 67 | CONFIG_NO_FB_CLEAR=y |
| 68 | CONFIG_VIDEO_SIMPLE=y |
| 69 | CONFIG_HEXDUMP=y |
| 70 | # CONFIG_GENERATE_SMBIOS_TABLE is not set |
| 71 | CONFIG_LMB_MAX_REGIONS=64 |
| 72 | |
| 73 | CONFIG_BAUDRATE=115200 |
| 74 | |
| 75 | # Uncomment to enable UART pre-relocation |
| 76 | CONFIG_DEBUG_UART=y |
| 77 | CONFIG_DEBUG_UART_ANNOUNCE=y |
| 78 | # This is the address of the debug-uart peripheral |
| 79 | # The value here is for SDM845, other platforms will vary |
| 80 | CONFIG_DEBUG_UART_BASE=0xa84000 |
| 81 | # Boards older than ~2018 pre-date the GENI driver and unfortunately |
| 82 | # aren't supported here |
| 83 | CONFIG_DEBUG_UART_MSM_GENI=y |
| 84 | # For sdm845 this is the UART clock rate |
| 85 | CONFIG_DEBUG_UART_CLOCK=7372800 |
| 86 | # Most newer boards have an oversampling value of 16 instead |
| 87 | # of 32, they need the clock rate to be doubled |
| 88 | #CONFIG_DEBUG_UART_CLOCK=14745600 |
| 89 | |
| 90 | CONFIG_LOG=y |
| 91 | CONFIG_HEXDUMP=y |
| 92 | CONFIG_CMD_LOG=y |
| 93 | CONFIG_LOG_MAX_LEVEL=9 |
| 94 | CONFIG_LOG_DEFAULT_LEVEL=9 |
| 95 | CONFIG_LOGLEVEL=9 |