blob: 46e4cee1d04c9dd3af28bdaa09b121f11e056719 [file] [log] [blame]
Rodolfo Giometti822af352007-04-03 14:27:18 +02001/*
2 * ISP116x HCD (Host Controller Driver) for u-boot.
3 *
4 * Copyright (C) 2006-2007 Rodolfo Giometti <giometti@linux.it>
5 * Copyright (C) 2006-2007 Eurotech S.p.A. <info@eurotech.it>
6 *
Wolfgang Denk1a459662013-07-08 09:37:19 +02007 * SPDX-License-Identifier: GPL-2.0+
Rodolfo Giometti822af352007-04-03 14:27:18 +02008 *
Marcel Ziswiler7817cb22007-12-30 03:30:46 +01009 * Derived in part from the SL811 HCD driver "u-boot/drivers/usb/sl811_usb.c"
Rodolfo Giometti822af352007-04-03 14:27:18 +020010 * (original copyright message follows):
11 *
12 * (C) Copyright 2004
13 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
14 *
15 * This code is based on linux driver for sl811hs chip, source at
16 * drivers/usb/host/sl811.c:
17 *
18 * SL811 Host Controller Interface driver for USB.
19 *
20 * Copyright (c) 2003/06, Courage Co., Ltd.
21 *
22 * Based on:
23 * 1.uhci.c by Linus Torvalds, Johannes Erdfelt, Randy Dunlap,
24 * Georg Acher, Deti Fliegl, Thomas Sailer, Roman Weissgaerber,
25 * Adam Richter, Gregory P. Smith;
26 * 2.Original SL811 driver (hc_sl811.o) by Pei Liu <pbl@cypress.com>
27 * 3.Rewrited as sl811.o by Yin Aihua <yinah:couragetech.com.cn>
28 *
29 * [[GNU/GPL disclaimer]]
30 *
Peter Tyser1e3827d2010-04-12 22:28:14 -050031 * and in part from AU1x00 OHCI HCD driver "u-boot/arch/mips/cpu/au1x00_usb_ohci.c"
Rodolfo Giometti822af352007-04-03 14:27:18 +020032 * (original copyright message follows):
33 *
34 * URB OHCI HCD (Host Controller Driver) for USB on the AU1x00.
35 *
36 * (C) Copyright 2003
Detlev Zundel792a09e2009-05-13 10:54:10 +020037 * Gary Jennejohn, DENX Software Engineering <garyj@denx.de>
Rodolfo Giometti822af352007-04-03 14:27:18 +020038 *
39 * [[GNU/GPL disclaimer]]
40 *
41 * Note: Part of this code has been derived from linux
42 */
43
44#include <common.h>
Rodolfo Giometti822af352007-04-03 14:27:18 +020045#include <asm/io.h>
46#include <usb.h>
47#include <malloc.h>
48#include <linux/list.h>
49
50/*
51 * ISP116x chips require certain delays between accesses to its
52 * registers. The following timing options exist.
53 *
54 * 1. Configure your memory controller (the best)
55 * 2. Use ndelay (easiest, poorest). For that, enable the following macro.
56 *
57 * Value is in microseconds.
58 */
59#ifdef ISP116X_HCD_USE_UDELAY
60#define UDELAY 1
61#endif
62
63/*
64 * On some (slowly?) machines an extra delay after data packing into
65 * controller's FIFOs is required, * otherwise you may get the following
66 * error:
67 *
68 * uboot> usb start
69 * (Re)start USB...
70 * USB: scanning bus for devices... isp116x: isp116x_submit_job: CTL:TIMEOUT
71 * isp116x: isp116x_submit_job: ****** FIFO not ready! ******
72 *
73 * USB device not responding, giving up (status=4)
74 * isp116x: isp116x_submit_job: ****** FIFO not empty! ******
75 * isp116x: isp116x_submit_job: ****** FIFO not empty! ******
76 * isp116x: isp116x_submit_job: ****** FIFO not empty! ******
77 * 3 USB Device(s) found
78 * scanning bus for storage devices... 0 Storage Device(s) found
79 *
80 * Value is in milliseconds.
81 */
82#ifdef ISP116X_HCD_USE_EXTRA_DELAY
83#define EXTRA_DELAY 2
84#endif
85
86/*
87 * Enable the following defines if you wish enable debugging messages.
88 */
89#undef DEBUG /* enable debugging messages */
90#undef TRACE /* enable tracing code */
91#undef VERBOSE /* verbose debugging messages */
92
93#include "isp116x.h"
94
95#define DRIVER_VERSION "08 Jan 2007"
96static const char hcd_name[] = "isp116x-hcd";
97
98struct isp116x isp116x_dev;
99struct isp116x_platform_data isp116x_board;
Timo Ketola785c1342007-09-24 14:50:32 +0300100static int got_rhsc; /* root hub status change */
Rodolfo Giometti822af352007-04-03 14:27:18 +0200101struct usb_device *devgone; /* device which was disconnected */
Timo Ketola785c1342007-09-24 14:50:32 +0300102static int rh_devnum; /* address of Root Hub endpoint */
Rodolfo Giometti822af352007-04-03 14:27:18 +0200103
104/* ------------------------------------------------------------------------- */
105
106#define ALIGN(x,a) (((x)+(a)-1UL)&~((a)-1UL))
107#define min_t(type,x,y) \
108 ({ type __x = (x); type __y = (y); __x < __y ? __x : __y; })
109
110/* ------------------------------------------------------------------------- */
111
112static int isp116x_reset(struct isp116x *isp116x);
113
114/* --- Debugging functions ------------------------------------------------- */
115
116#define isp116x_show_reg(d, r) { \
117 if ((r) < 0x20) { \
118 DBG("%-12s[%02x]: %08x", #r, \
119 r, isp116x_read_reg32(d, r)); \
120 } else { \
121 DBG("%-12s[%02x]: %04x", #r, \
Wolfgang Denk53677ef2008-05-20 16:00:29 +0200122 r, isp116x_read_reg16(d, r)); \
Rodolfo Giometti822af352007-04-03 14:27:18 +0200123 } \
124}
125
126#define isp116x_show_regs(d) { \
127 isp116x_show_reg(d, HCREVISION); \
128 isp116x_show_reg(d, HCCONTROL); \
129 isp116x_show_reg(d, HCCMDSTAT); \
130 isp116x_show_reg(d, HCINTSTAT); \
131 isp116x_show_reg(d, HCINTENB); \
132 isp116x_show_reg(d, HCFMINTVL); \
133 isp116x_show_reg(d, HCFMREM); \
134 isp116x_show_reg(d, HCFMNUM); \
135 isp116x_show_reg(d, HCLSTHRESH); \
136 isp116x_show_reg(d, HCRHDESCA); \
137 isp116x_show_reg(d, HCRHDESCB); \
138 isp116x_show_reg(d, HCRHSTATUS); \
139 isp116x_show_reg(d, HCRHPORT1); \
140 isp116x_show_reg(d, HCRHPORT2); \
141 isp116x_show_reg(d, HCHWCFG); \
142 isp116x_show_reg(d, HCDMACFG); \
143 isp116x_show_reg(d, HCXFERCTR); \
144 isp116x_show_reg(d, HCuPINT); \
145 isp116x_show_reg(d, HCuPINTENB); \
146 isp116x_show_reg(d, HCCHIPID); \
147 isp116x_show_reg(d, HCSCRATCH); \
148 isp116x_show_reg(d, HCITLBUFLEN); \
149 isp116x_show_reg(d, HCATLBUFLEN); \
150 isp116x_show_reg(d, HCBUFSTAT); \
151 isp116x_show_reg(d, HCRDITL0LEN); \
152 isp116x_show_reg(d, HCRDITL1LEN); \
153}
154
155#if defined(TRACE)
156
157static int isp116x_get_current_frame_number(struct usb_device *usb_dev)
158{
159 struct isp116x *isp116x = &isp116x_dev;
160
161 return isp116x_read_reg32(isp116x, HCFMNUM);
162}
163
164static void dump_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
165 int len, char *str)
166{
167#if defined(VERBOSE)
168 int i;
169#endif
170
171 DBG("%s URB:[%4x] dev:%2d,ep:%2d-%c,type:%s,len:%d stat:%#lx",
172 str,
173 isp116x_get_current_frame_number(dev),
174 usb_pipedevice(pipe),
175 usb_pipeendpoint(pipe),
176 usb_pipeout(pipe) ? 'O' : 'I',
177 usb_pipetype(pipe) < 2 ?
178 (usb_pipeint(pipe) ?
179 "INTR" : "ISOC") :
180 (usb_pipecontrol(pipe) ? "CTRL" : "BULK"), len, dev->status);
181#if defined(VERBOSE)
182 if (len > 0 && buffer) {
183 printf(__FILE__ ": data(%d):", len);
184 for (i = 0; i < 16 && i < len; i++)
185 printf(" %02x", ((__u8 *) buffer)[i]);
186 printf("%s\n", i < len ? "..." : "");
187 }
188#endif
189}
190
191#define PTD_DIR_STR(ptd) ({char __c; \
192 switch(PTD_GET_DIR(ptd)){ \
193 case 0: __c = 's'; break; \
194 case 1: __c = 'o'; break; \
195 default: __c = 'i'; break; \
196 }; __c;})
197
198/*
199 Dump PTD info. The code documents the format
200 perfectly, right :)
201*/
202static inline void dump_ptd(struct ptd *ptd)
203{
204#if defined(VERBOSE)
205 int k;
206#endif
207
208 DBG("PTD(ext) : cc:%x %d%c%d %d,%d,%d t:%x %x%x%x",
209 PTD_GET_CC(ptd),
210 PTD_GET_FA(ptd), PTD_DIR_STR(ptd), PTD_GET_EP(ptd),
211 PTD_GET_COUNT(ptd), PTD_GET_LEN(ptd), PTD_GET_MPS(ptd),
212 PTD_GET_TOGGLE(ptd),
213 PTD_GET_ACTIVE(ptd), PTD_GET_SPD(ptd), PTD_GET_LAST(ptd));
214#if defined(VERBOSE)
215 printf("isp116x: %s: PTD(byte): ", __FUNCTION__);
216 for (k = 0; k < sizeof(struct ptd); ++k)
217 printf("%02x ", ((u8 *) ptd)[k]);
218 printf("\n");
219#endif
220}
221
222static inline void dump_ptd_data(struct ptd *ptd, u8 * buf, int type)
223{
224#if defined(VERBOSE)
225 int k;
226
227 if (type == 0 /* 0ut data */ ) {
228 printf("isp116x: %s: out data: ", __FUNCTION__);
229 for (k = 0; k < PTD_GET_LEN(ptd); ++k)
230 printf("%02x ", ((u8 *) buf)[k]);
231 printf("\n");
232 }
233 if (type == 1 /* 1n data */ ) {
234 printf("isp116x: %s: in data: ", __FUNCTION__);
235 for (k = 0; k < PTD_GET_COUNT(ptd); ++k)
236 printf("%02x ", ((u8 *) buf)[k]);
237 printf("\n");
238 }
239
240 if (PTD_GET_LAST(ptd))
241 DBG("--- last PTD ---");
242#endif
243}
244
245#else
246
247#define dump_msg(dev, pipe, buffer, len, str) do { } while (0)
248#define dump_pkt(dev, pipe, buffer, len, setup, str, small) do {} while (0)
249
250#define dump_ptd(ptd) do {} while (0)
251#define dump_ptd_data(ptd, buf, type) do {} while (0)
252
253#endif
254
255/* --- Virtual Root Hub ---------------------------------------------------- */
256
Stephen Warreneb838e72014-02-13 21:15:18 -0700257#include <usbroothubdes.h>
Rodolfo Giometti822af352007-04-03 14:27:18 +0200258
259/*
260 * Hub class-specific descriptor is constructed dynamically
261 */
262
263/* --- Virtual root hub management functions ------------------------------- */
264
265static int rh_check_port_status(struct isp116x *isp116x)
266{
267 u32 temp, ndp, i;
268 int res;
269
270 res = -1;
271 temp = isp116x_read_reg32(isp116x, HCRHSTATUS);
272 ndp = (temp & RH_A_NDP);
273 for (i = 0; i < ndp; i++) {
274 temp = isp116x_read_reg32(isp116x, HCRHPORT1 + i);
275 /* check for a device disconnect */
276 if (((temp & (RH_PS_PESC | RH_PS_CSC)) ==
277 (RH_PS_PESC | RH_PS_CSC)) && ((temp & RH_PS_CCS) == 0)) {
278 res = i;
279 break;
280 }
281 }
282 return res;
283}
284
285/* --- HC management functions --------------------------------------------- */
286
287/* Write len bytes to fifo, pad till 32-bit boundary
288 */
289static void write_ptddata_to_fifo(struct isp116x *isp116x, void *buf, int len)
290{
291 u8 *dp = (u8 *) buf;
292 u16 *dp2 = (u16 *) buf;
293 u16 w;
294 int quot = len % 4;
295
296 if ((unsigned long)dp2 & 1) {
297 /* not aligned */
298 for (; len > 1; len -= 2) {
299 w = *dp++;
300 w |= *dp++ << 8;
301 isp116x_raw_write_data16(isp116x, w);
302 }
303 if (len)
304 isp116x_write_data16(isp116x, (u16) * dp);
305 } else {
306 /* aligned */
307 for (; len > 1; len -= 2)
308 isp116x_raw_write_data16(isp116x, *dp2++);
309 if (len)
310 isp116x_write_data16(isp116x, 0xff & *((u8 *) dp2));
311 }
312 if (quot == 1 || quot == 2)
313 isp116x_raw_write_data16(isp116x, 0);
314}
315
316/* Read len bytes from fifo and then read till 32-bit boundary
317 */
318static void read_ptddata_from_fifo(struct isp116x *isp116x, void *buf, int len)
319{
320 u8 *dp = (u8 *) buf;
321 u16 *dp2 = (u16 *) buf;
322 u16 w;
323 int quot = len % 4;
324
325 if ((unsigned long)dp2 & 1) {
326 /* not aligned */
327 for (; len > 1; len -= 2) {
328 w = isp116x_raw_read_data16(isp116x);
329 *dp++ = w & 0xff;
330 *dp++ = (w >> 8) & 0xff;
331 }
332 if (len)
333 *dp = 0xff & isp116x_read_data16(isp116x);
334 } else {
335 /* aligned */
336 for (; len > 1; len -= 2)
337 *dp2++ = isp116x_raw_read_data16(isp116x);
338 if (len)
339 *(u8 *) dp2 = 0xff & isp116x_read_data16(isp116x);
340 }
341 if (quot == 1 || quot == 2)
342 isp116x_raw_read_data16(isp116x);
343}
344
345/* Write PTD's and data for scheduled transfers into the fifo ram.
346 * Fifo must be empty and ready */
347static void pack_fifo(struct isp116x *isp116x, struct usb_device *dev,
348 unsigned long pipe, struct ptd *ptd, int n, void *data,
349 int len)
350{
351 int buflen = n * sizeof(struct ptd) + len;
352 int i, done;
353
354 DBG("--- pack buffer %p - %d bytes (fifo %d) ---", data, len, buflen);
355
356 isp116x_write_reg16(isp116x, HCuPINT, HCuPINT_AIIEOT);
357 isp116x_write_reg16(isp116x, HCXFERCTR, buflen);
358 isp116x_write_addr(isp116x, HCATLPORT | ISP116x_WRITE_OFFSET);
359
360 done = 0;
361 for (i = 0; i < n; i++) {
362 DBG("i=%d - done=%d - len=%d", i, done, PTD_GET_LEN(&ptd[i]));
363
364 dump_ptd(&ptd[i]);
365 isp116x_write_data16(isp116x, ptd[i].count);
366 isp116x_write_data16(isp116x, ptd[i].mps);
367 isp116x_write_data16(isp116x, ptd[i].len);
368 isp116x_write_data16(isp116x, ptd[i].faddr);
369
370 dump_ptd_data(&ptd[i], (__u8 *) data + done, 0);
371 write_ptddata_to_fifo(isp116x,
372 (__u8 *) data + done,
373 PTD_GET_LEN(&ptd[i]));
374
375 done += PTD_GET_LEN(&ptd[i]);
376 }
377}
378
379/* Read the processed PTD's and data from fifo ram back to URBs' buffers.
380 * Fifo must be full and done */
381static int unpack_fifo(struct isp116x *isp116x, struct usb_device *dev,
382 unsigned long pipe, struct ptd *ptd, int n, void *data,
383 int len)
384{
385 int buflen = n * sizeof(struct ptd) + len;
386 int i, done, cc, ret;
387
388 isp116x_write_reg16(isp116x, HCuPINT, HCuPINT_AIIEOT);
389 isp116x_write_reg16(isp116x, HCXFERCTR, buflen);
390 isp116x_write_addr(isp116x, HCATLPORT);
391
392 ret = TD_CC_NOERROR;
393 done = 0;
394 for (i = 0; i < n; i++) {
395 DBG("i=%d - done=%d - len=%d", i, done, PTD_GET_LEN(&ptd[i]));
396
397 ptd[i].count = isp116x_read_data16(isp116x);
398 ptd[i].mps = isp116x_read_data16(isp116x);
399 ptd[i].len = isp116x_read_data16(isp116x);
400 ptd[i].faddr = isp116x_read_data16(isp116x);
401 dump_ptd(&ptd[i]);
402
403 read_ptddata_from_fifo(isp116x,
404 (__u8 *) data + done,
405 PTD_GET_LEN(&ptd[i]));
406 dump_ptd_data(&ptd[i], (__u8 *) data + done, 1);
407
408 done += PTD_GET_LEN(&ptd[i]);
409
410 cc = PTD_GET_CC(&ptd[i]);
Timo Ketola785c1342007-09-24 14:50:32 +0300411
412 /* Data underrun means basically that we had more buffer space than
413 * the function had data. It is perfectly normal but upper levels have
414 * to know how much we actually transferred.
415 */
416 if (cc == TD_NOTACCESSED ||
417 (cc != TD_CC_NOERROR && (ret == TD_CC_NOERROR || ret == TD_DATAUNDERRUN)))
Rodolfo Giometti822af352007-04-03 14:27:18 +0200418 ret = cc;
419 }
420
421 DBG("--- unpack buffer %p - %d bytes (fifo %d) ---", data, len, buflen);
422
423 return ret;
424}
425
426/* Interrupt handling
427 */
428static int isp116x_interrupt(struct isp116x *isp116x)
429{
430 u16 irqstat;
431 u32 intstat;
432 int ret = 0;
433
434 isp116x_write_reg16(isp116x, HCuPINTENB, 0);
435 irqstat = isp116x_read_reg16(isp116x, HCuPINT);
436 isp116x_write_reg16(isp116x, HCuPINT, irqstat);
437 DBG(">>>>>> irqstat %x <<<<<<", irqstat);
438
439 if (irqstat & HCuPINT_ATL) {
440 DBG(">>>>>> HCuPINT_ATL <<<<<<");
Rodolfo Giometti9a1d00f2007-06-06 10:08:12 +0200441 udelay(500);
Rodolfo Giometti822af352007-04-03 14:27:18 +0200442 ret = 1;
443 }
444
445 if (irqstat & HCuPINT_OPR) {
446 intstat = isp116x_read_reg32(isp116x, HCINTSTAT);
447 isp116x_write_reg32(isp116x, HCINTSTAT, intstat);
448 DBG(">>>>>> HCuPINT_OPR %x <<<<<<", intstat);
449
450 if (intstat & HCINT_UE) {
451 ERR("unrecoverable error, controller disabled");
452
453 /* FIXME: be optimistic, hope that bug won't repeat
454 * often. Make some non-interrupt context restart the
455 * controller. Count and limit the retries though;
456 * either hardware or software errors can go forever...
457 */
458 isp116x_reset(isp116x);
459 ret = -1;
460 return -1;
461 }
462
463 if (intstat & HCINT_RHSC) {
464 got_rhsc = 1;
465 ret = 1;
466 /* When root hub or any of its ports is going
467 to come out of suspend, it may take more
468 than 10ms for status bits to stabilize. */
Mike Frysinger5b84dd62012-03-05 13:47:00 +0000469 mdelay(20);
Rodolfo Giometti822af352007-04-03 14:27:18 +0200470 }
471
472 if (intstat & HCINT_SO) {
473 ERR("schedule overrun");
474 ret = -1;
475 }
476
477 irqstat &= ~HCuPINT_OPR;
478 }
479
480 return ret;
481}
482
Timo Ketola785c1342007-09-24 14:50:32 +0300483/* With one PTD we can transfer almost 1K in one go;
484 * HC does the splitting into endpoint digestible transactions
485 */
486struct ptd ptd[1];
487
Rodolfo Giometti822af352007-04-03 14:27:18 +0200488static inline int max_transfer_len(struct usb_device *dev, unsigned long pipe)
489{
Timo Ketola785c1342007-09-24 14:50:32 +0300490 unsigned mpck = usb_maxpacket(dev, pipe);
491
492 /* One PTD can transfer 1023 bytes but try to always
493 * transfer multiples of endpoint buffer size
494 */
495 return 1023 / mpck * mpck;
Rodolfo Giometti822af352007-04-03 14:27:18 +0200496}
497
498/* Do an USB transfer
499 */
500static int isp116x_submit_job(struct usb_device *dev, unsigned long pipe,
501 int dir, void *buffer, int len)
502{
503 struct isp116x *isp116x = &isp116x_dev;
504 int type = usb_pipetype(pipe);
505 int epnum = usb_pipeendpoint(pipe);
506 int max = usb_maxpacket(dev, pipe);
507 int dir_out = usb_pipeout(pipe);
Ilya Yanokc60795f2012-11-06 13:48:20 +0000508 int speed_low = (dev->speed == USB_SPEED_LOW);
Timo Ketola785c1342007-09-24 14:50:32 +0300509 int i, done = 0, stat, timeout, cc;
510
511 /* 500 frames or 0.5s timeout when function is busy and NAKs transactions for a while */
512 int retries = 500;
Rodolfo Giometti822af352007-04-03 14:27:18 +0200513
514 DBG("------------------------------------------------");
515 dump_msg(dev, pipe, buffer, len, "SUBMIT");
516 DBG("------------------------------------------------");
517
Timo Ketola785c1342007-09-24 14:50:32 +0300518 if (len >= 1024) {
519 ERR("Too big job");
520 dev->status = USB_ST_CRC_ERR;
521 return -1;
522 }
523
Rodolfo Giometti822af352007-04-03 14:27:18 +0200524 if (isp116x->disabled) {
525 ERR("EPIPE");
526 dev->status = USB_ST_CRC_ERR;
527 return -1;
528 }
529
530 /* device pulled? Shortcut the action. */
531 if (devgone == dev) {
532 ERR("ENODEV");
533 dev->status = USB_ST_CRC_ERR;
534 return USB_ST_CRC_ERR;
535 }
536
537 if (!max) {
538 ERR("pipesize for pipe %lx is zero", pipe);
539 dev->status = USB_ST_CRC_ERR;
540 return -1;
541 }
542
543 if (type == PIPE_ISOCHRONOUS) {
544 ERR("isochronous transfers not supported");
545 dev->status = USB_ST_CRC_ERR;
546 return -1;
547 }
548
549 /* FIFO not empty? */
550 if (isp116x_read_reg16(isp116x, HCBUFSTAT) & HCBUFSTAT_ATL_FULL) {
551 ERR("****** FIFO not empty! ******");
552 dev->status = USB_ST_BUF_ERR;
553 return -1;
554 }
555
556 retry:
557 isp116x_write_reg32(isp116x, HCINTSTAT, 0xff);
558
559 /* Prepare the PTD data */
Timo Ketola785c1342007-09-24 14:50:32 +0300560 ptd->count = PTD_CC_MSK | PTD_ACTIVE_MSK |
561 PTD_TOGGLE(usb_gettoggle(dev, epnum, dir_out));
562 ptd->mps = PTD_MPS(max) | PTD_SPD(speed_low) | PTD_EP(epnum) | PTD_LAST_MSK;
563 ptd->len = PTD_LEN(len) | PTD_DIR(dir);
564 ptd->faddr = PTD_FA(usb_pipedevice(pipe));
Rodolfo Giometti822af352007-04-03 14:27:18 +0200565
Timo Ketola785c1342007-09-24 14:50:32 +0300566retry_same:
Rodolfo Giometti822af352007-04-03 14:27:18 +0200567 /* Pack data into FIFO ram */
Timo Ketola785c1342007-09-24 14:50:32 +0300568 pack_fifo(isp116x, dev, pipe, ptd, 1, buffer, len);
Rodolfo Giometti822af352007-04-03 14:27:18 +0200569#ifdef EXTRA_DELAY
Mike Frysinger5b84dd62012-03-05 13:47:00 +0000570 mdelay(EXTRA_DELAY);
Rodolfo Giometti822af352007-04-03 14:27:18 +0200571#endif
572
573 /* Start the data transfer */
574
575 /* Allow more time for a BULK device to react - some are slow */
Remy Bohmer9dbc3662008-10-10 10:23:22 +0200576 if (usb_pipebulk(pipe))
Rodolfo Giometti822af352007-04-03 14:27:18 +0200577 timeout = 5000;
578 else
579 timeout = 100;
580
581 /* Wait for it to complete */
582 for (;;) {
583 /* Check whether the controller is done */
584 stat = isp116x_interrupt(isp116x);
585
586 if (stat < 0) {
587 dev->status = USB_ST_CRC_ERR;
588 break;
589 }
590 if (stat > 0)
591 break;
592
593 /* Check the timeout */
594 if (--timeout)
595 udelay(1);
596 else {
597 ERR("CTL:TIMEOUT ");
598 stat = USB_ST_CRC_ERR;
599 break;
600 }
601 }
602
603 /* We got an Root Hub Status Change interrupt */
604 if (got_rhsc) {
605 isp116x_show_regs(isp116x);
606
607 got_rhsc = 0;
608
609 /* Abuse timeout */
610 timeout = rh_check_port_status(isp116x);
611 if (timeout >= 0) {
612 /*
613 * FIXME! NOTE! AAAARGH!
614 * This is potentially dangerous because it assumes
615 * that only one device is ever plugged in!
616 */
617 devgone = dev;
618 }
619 }
620
621 /* Ok, now we can read transfer status */
622
623 /* FIFO not ready? */
624 if (!(isp116x_read_reg16(isp116x, HCBUFSTAT) & HCBUFSTAT_ATL_DONE)) {
625 ERR("****** FIFO not ready! ******");
626 dev->status = USB_ST_BUF_ERR;
627 return -1;
628 }
629
630 /* Unpack data from FIFO ram */
Timo Ketola785c1342007-09-24 14:50:32 +0300631 cc = unpack_fifo(isp116x, dev, pipe, ptd, 1, buffer, len);
Rodolfo Giometti822af352007-04-03 14:27:18 +0200632
Timo Ketola785c1342007-09-24 14:50:32 +0300633 i = PTD_GET_COUNT(ptd);
634 done += i;
635 buffer += i;
636 len -= i;
637
638 /* There was some kind of real problem; Prepare the PTD again
639 * and retry from the failed transaction on
Rodolfo Giometti822af352007-04-03 14:27:18 +0200640 */
Timo Ketola785c1342007-09-24 14:50:32 +0300641 if (cc && cc != TD_NOTACCESSED && cc != TD_DATAUNDERRUN) {
642 if (retries >= 100) {
643 retries -= 100;
644 /* The chip will have toggled the toggle bit for the failed
645 * transaction too. We have to toggle it back.
646 */
647 usb_settoggle(dev, epnum, dir_out, !PTD_GET_TOGGLE(ptd));
648 goto retry;
649 }
650 }
651 /* "Normal" errors; TD_NOTACCESSED would mean in effect that the function have NAKed
652 * the transactions from the first on for the whole frame. It may be busy and we retry
653 * with the same PTD. PTD_ACTIVE (and not TD_NOTACCESSED) would mean that some of the
654 * PTD didn't make it because the function was busy or the frame ended before the PTD
655 * finished. We prepare the rest of the data and try again.
656 */
657 else if (cc == TD_NOTACCESSED || PTD_GET_ACTIVE(ptd) || (cc != TD_DATAUNDERRUN && PTD_GET_COUNT(ptd) < PTD_GET_LEN(ptd))) {
658 if (retries) {
659 --retries;
660 if (cc == TD_NOTACCESSED && PTD_GET_ACTIVE(ptd) && !PTD_GET_COUNT(ptd)) goto retry_same;
661 usb_settoggle(dev, epnum, dir_out, PTD_GET_TOGGLE(ptd));
662 goto retry;
663 }
Rodolfo Giometti822af352007-04-03 14:27:18 +0200664 }
665
Timo Ketola785c1342007-09-24 14:50:32 +0300666 if (cc != TD_CC_NOERROR && cc != TD_DATAUNDERRUN) {
Rodolfo Giometti822af352007-04-03 14:27:18 +0200667 DBG("****** completition code error %x ******", cc);
668 switch (cc) {
669 case TD_CC_BITSTUFFING:
670 dev->status = USB_ST_BIT_ERR;
671 break;
672 case TD_CC_STALL:
673 dev->status = USB_ST_STALLED;
674 break;
675 case TD_BUFFEROVERRUN:
676 case TD_BUFFERUNDERRUN:
677 dev->status = USB_ST_BUF_ERR;
678 break;
679 default:
680 dev->status = USB_ST_CRC_ERR;
681 }
682 return -cc;
683 }
Timo Ketola785c1342007-09-24 14:50:32 +0300684 else usb_settoggle(dev, epnum, dir_out, PTD_GET_TOGGLE(ptd));
Rodolfo Giometti822af352007-04-03 14:27:18 +0200685
686 dump_msg(dev, pipe, buffer, len, "SUBMIT(ret)");
687
688 dev->status = 0;
689 return done;
690}
691
692/* Adapted from au1x00_usb_ohci.c
693 */
694static int isp116x_submit_rh_msg(struct usb_device *dev, unsigned long pipe,
695 void *buffer, int transfer_len,
696 struct devrequest *cmd)
697{
698 struct isp116x *isp116x = &isp116x_dev;
699 u32 tmp = 0;
700
701 int leni = transfer_len;
702 int len = 0;
703 int stat = 0;
704 u32 datab[4];
705 u8 *data_buf = (u8 *) datab;
706 u16 bmRType_bReq;
707 u16 wValue;
708 u16 wIndex;
709 u16 wLength;
710
Remy Bohmer9dbc3662008-10-10 10:23:22 +0200711 if (usb_pipeint(pipe)) {
Rodolfo Giometti822af352007-04-03 14:27:18 +0200712 INFO("Root-Hub submit IRQ: NOT implemented");
713 return 0;
714 }
715
716 bmRType_bReq = cmd->requesttype | (cmd->request << 8);
717 wValue = swap_16(cmd->value);
718 wIndex = swap_16(cmd->index);
719 wLength = swap_16(cmd->length);
720
721 DBG("--- HUB ----------------------------------------");
722 DBG("submit rh urb, req=%x val=%#x index=%#x len=%d",
723 bmRType_bReq, wValue, wIndex, wLength);
724 dump_msg(dev, pipe, buffer, transfer_len, "RH");
725 DBG("------------------------------------------------");
726
727 switch (bmRType_bReq) {
728 case RH_GET_STATUS:
729 DBG("RH_GET_STATUS");
730
731 *(__u16 *) data_buf = swap_16(1);
732 len = 2;
733 break;
734
735 case RH_GET_STATUS | RH_INTERFACE:
736 DBG("RH_GET_STATUS | RH_INTERFACE");
737
738 *(__u16 *) data_buf = swap_16(0);
739 len = 2;
740 break;
741
742 case RH_GET_STATUS | RH_ENDPOINT:
743 DBG("RH_GET_STATUS | RH_ENDPOINT");
744
745 *(__u16 *) data_buf = swap_16(0);
746 len = 2;
747 break;
748
749 case RH_GET_STATUS | RH_CLASS:
750 DBG("RH_GET_STATUS | RH_CLASS");
751
752 tmp = isp116x_read_reg32(isp116x, HCRHSTATUS);
753
754 *(__u32 *) data_buf = swap_32(tmp & ~(RH_HS_CRWE | RH_HS_DRWE));
755 len = 4;
756 break;
757
758 case RH_GET_STATUS | RH_OTHER | RH_CLASS:
759 DBG("RH_GET_STATUS | RH_OTHER | RH_CLASS");
760
761 tmp = isp116x_read_reg32(isp116x, HCRHPORT1 + wIndex - 1);
762 *(__u32 *) data_buf = swap_32(tmp);
763 isp116x_show_regs(isp116x);
764 len = 4;
765 break;
766
767 case RH_CLEAR_FEATURE | RH_ENDPOINT:
768 DBG("RH_CLEAR_FEATURE | RH_ENDPOINT");
769
770 switch (wValue) {
771 case RH_ENDPOINT_STALL:
772 DBG("C_HUB_ENDPOINT_STALL");
773 len = 0;
774 break;
775 }
776 break;
777
778 case RH_CLEAR_FEATURE | RH_CLASS:
779 DBG("RH_CLEAR_FEATURE | RH_CLASS");
780
781 switch (wValue) {
782 case RH_C_HUB_LOCAL_POWER:
783 DBG("C_HUB_LOCAL_POWER");
784 len = 0;
785 break;
786
787 case RH_C_HUB_OVER_CURRENT:
788 DBG("C_HUB_OVER_CURRENT");
789 isp116x_write_reg32(isp116x, HCRHSTATUS, RH_HS_OCIC);
790 len = 0;
791 break;
792 }
793 break;
794
795 case RH_CLEAR_FEATURE | RH_OTHER | RH_CLASS:
796 DBG("RH_CLEAR_FEATURE | RH_OTHER | RH_CLASS");
797
798 switch (wValue) {
799 case RH_PORT_ENABLE:
800 isp116x_write_reg32(isp116x, HCRHPORT1 + wIndex - 1,
801 RH_PS_CCS);
802 len = 0;
803 break;
804
805 case RH_PORT_SUSPEND:
806 isp116x_write_reg32(isp116x, HCRHPORT1 + wIndex - 1,
807 RH_PS_POCI);
808 len = 0;
809 break;
810
811 case RH_PORT_POWER:
812 isp116x_write_reg32(isp116x, HCRHPORT1 + wIndex - 1,
813 RH_PS_LSDA);
814 len = 0;
815 break;
816
817 case RH_C_PORT_CONNECTION:
818 isp116x_write_reg32(isp116x, HCRHPORT1 + wIndex - 1,
819 RH_PS_CSC);
820 len = 0;
821 break;
822
823 case RH_C_PORT_ENABLE:
824 isp116x_write_reg32(isp116x, HCRHPORT1 + wIndex - 1,
825 RH_PS_PESC);
826 len = 0;
827 break;
828
829 case RH_C_PORT_SUSPEND:
830 isp116x_write_reg32(isp116x, HCRHPORT1 + wIndex - 1,
831 RH_PS_PSSC);
832 len = 0;
833 break;
834
835 case RH_C_PORT_OVER_CURRENT:
836 isp116x_write_reg32(isp116x, HCRHPORT1 + wIndex - 1,
837 RH_PS_POCI);
838 len = 0;
839 break;
840
841 case RH_C_PORT_RESET:
842 isp116x_write_reg32(isp116x, HCRHPORT1 + wIndex - 1,
843 RH_PS_PRSC);
844 len = 0;
845 break;
846
847 default:
848 ERR("invalid wValue");
849 stat = USB_ST_STALLED;
850 }
851
852 isp116x_show_regs(isp116x);
853
854 break;
855
856 case RH_SET_FEATURE | RH_OTHER | RH_CLASS:
857 DBG("RH_SET_FEATURE | RH_OTHER | RH_CLASS");
858
859 switch (wValue) {
860 case RH_PORT_SUSPEND:
861 isp116x_write_reg32(isp116x, HCRHPORT1 + wIndex - 1,
862 RH_PS_PSS);
863 len = 0;
864 break;
865
866 case RH_PORT_RESET:
867 /* Spin until any current reset finishes */
868 while (1) {
869 tmp =
870 isp116x_read_reg32(isp116x,
871 HCRHPORT1 + wIndex - 1);
872 if (!(tmp & RH_PS_PRS))
873 break;
Mike Frysinger5b84dd62012-03-05 13:47:00 +0000874 mdelay(1);
Rodolfo Giometti822af352007-04-03 14:27:18 +0200875 }
876 isp116x_write_reg32(isp116x, HCRHPORT1 + wIndex - 1,
877 RH_PS_PRS);
Mike Frysinger5b84dd62012-03-05 13:47:00 +0000878 mdelay(10);
Rodolfo Giometti822af352007-04-03 14:27:18 +0200879
880 len = 0;
881 break;
882
883 case RH_PORT_POWER:
884 isp116x_write_reg32(isp116x, HCRHPORT1 + wIndex - 1,
885 RH_PS_PPS);
886 len = 0;
887 break;
888
889 case RH_PORT_ENABLE:
890 isp116x_write_reg32(isp116x, HCRHPORT1 + wIndex - 1,
891 RH_PS_PES);
892 len = 0;
893 break;
894
895 default:
896 ERR("invalid wValue");
897 stat = USB_ST_STALLED;
898 }
899
900 isp116x_show_regs(isp116x);
901
902 break;
903
904 case RH_SET_ADDRESS:
905 DBG("RH_SET_ADDRESS");
906
907 rh_devnum = wValue;
908 len = 0;
909 break;
910
911 case RH_GET_DESCRIPTOR:
912 DBG("RH_GET_DESCRIPTOR: %x, %d", wValue, wLength);
913
914 switch (wValue) {
915 case (USB_DT_DEVICE << 8): /* device descriptor */
916 len = min_t(unsigned int,
917 leni, min_t(unsigned int,
918 sizeof(root_hub_dev_des),
919 wLength));
920 data_buf = root_hub_dev_des;
921 break;
922
923 case (USB_DT_CONFIG << 8): /* configuration descriptor */
924 len = min_t(unsigned int,
925 leni, min_t(unsigned int,
926 sizeof(root_hub_config_des),
927 wLength));
928 data_buf = root_hub_config_des;
929 break;
930
931 case ((USB_DT_STRING << 8) | 0x00): /* string 0 descriptors */
932 len = min_t(unsigned int,
933 leni, min_t(unsigned int,
934 sizeof(root_hub_str_index0),
935 wLength));
936 data_buf = root_hub_str_index0;
937 break;
938
939 case ((USB_DT_STRING << 8) | 0x01): /* string 1 descriptors */
940 len = min_t(unsigned int,
941 leni, min_t(unsigned int,
942 sizeof(root_hub_str_index1),
943 wLength));
944 data_buf = root_hub_str_index1;
945 break;
946
947 default:
948 ERR("invalid wValue");
949 stat = USB_ST_STALLED;
950 }
951
952 break;
953
954 case RH_GET_DESCRIPTOR | RH_CLASS:
955 DBG("RH_GET_DESCRIPTOR | RH_CLASS");
956
957 tmp = isp116x_read_reg32(isp116x, HCRHDESCA);
958
959 data_buf[0] = 0x09; /* min length; */
960 data_buf[1] = 0x29;
961 data_buf[2] = tmp & RH_A_NDP;
962 data_buf[3] = 0;
963 if (tmp & RH_A_PSM) /* per-port power switching? */
964 data_buf[3] |= 0x01;
965 if (tmp & RH_A_NOCP) /* no overcurrent reporting? */
966 data_buf[3] |= 0x10;
967 else if (tmp & RH_A_OCPM) /* per-port overcurrent rep? */
968 data_buf[3] |= 0x08;
969
970 /* Corresponds to data_buf[4-7] */
971 datab[1] = 0;
972 data_buf[5] = (tmp & RH_A_POTPGT) >> 24;
973
974 tmp = isp116x_read_reg32(isp116x, HCRHDESCB);
975
976 data_buf[7] = tmp & RH_B_DR;
977 if (data_buf[2] < 7)
978 data_buf[8] = 0xff;
979 else {
980 data_buf[0] += 2;
981 data_buf[8] = (tmp & RH_B_DR) >> 8;
982 data_buf[10] = data_buf[9] = 0xff;
983 }
984
985 len = min_t(unsigned int, leni,
986 min_t(unsigned int, data_buf[0], wLength));
987 break;
988
989 case RH_GET_CONFIGURATION:
990 DBG("RH_GET_CONFIGURATION");
991
992 *(__u8 *) data_buf = 0x01;
993 len = 1;
994 break;
995
996 case RH_SET_CONFIGURATION:
997 DBG("RH_SET_CONFIGURATION");
998
999 isp116x_write_reg32(isp116x, HCRHSTATUS, RH_HS_LPSC);
1000 len = 0;
1001 break;
1002
1003 default:
1004 ERR("*** *** *** unsupported root hub command *** *** ***");
1005 stat = USB_ST_STALLED;
1006 }
1007
1008 len = min_t(int, len, leni);
1009 if (buffer != data_buf)
1010 memcpy(buffer, data_buf, len);
1011
1012 dev->act_len = len;
1013 dev->status = stat;
1014 DBG("dev act_len %d, status %d", dev->act_len, dev->status);
1015
1016 dump_msg(dev, pipe, buffer, transfer_len, "RH(ret)");
1017
1018 return stat;
1019}
1020
1021/* --- Transfer functions -------------------------------------------------- */
1022
1023int submit_int_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
1024 int len, int interval)
1025{
1026 DBG("dev=%p pipe=%#lx buf=%p size=%d int=%d",
1027 dev, pipe, buffer, len, interval);
1028
1029 return -1;
1030}
1031
1032int submit_control_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
1033 int len, struct devrequest *setup)
1034{
1035 int devnum = usb_pipedevice(pipe);
1036 int epnum = usb_pipeendpoint(pipe);
1037 int max = max_transfer_len(dev, pipe);
1038 int dir_in = usb_pipein(pipe);
1039 int done, ret;
1040
1041 /* Control message is for the HUB? */
1042 if (devnum == rh_devnum)
1043 return isp116x_submit_rh_msg(dev, pipe, buffer, len, setup);
1044
1045 /* Ok, no HUB message so send the message to the device */
1046
1047 /* Setup phase */
1048 DBG("--- SETUP PHASE --------------------------------");
1049 usb_settoggle(dev, epnum, 1, 0);
1050 ret = isp116x_submit_job(dev, pipe,
1051 PTD_DIR_SETUP,
1052 setup, sizeof(struct devrequest));
1053 if (ret < 0) {
1054 DBG("control setup phase error (ret = %d", ret);
1055 return -1;
1056 }
1057
1058 /* Data phase */
1059 DBG("--- DATA PHASE ---------------------------------");
1060 done = 0;
1061 usb_settoggle(dev, epnum, !dir_in, 1);
1062 while (done < len) {
1063 ret = isp116x_submit_job(dev, pipe,
1064 dir_in ? PTD_DIR_IN : PTD_DIR_OUT,
1065 (__u8 *) buffer + done,
1066 max > len - done ? len - done : max);
1067 if (ret < 0) {
1068 DBG("control data phase error (ret = %d)", ret);
1069 return -1;
1070 }
1071 done += ret;
1072
1073 if (dir_in && ret < max) /* short packet */
1074 break;
1075 }
1076
1077 /* Status phase */
1078 DBG("--- STATUS PHASE -------------------------------");
1079 usb_settoggle(dev, epnum, !dir_in, 1);
1080 ret = isp116x_submit_job(dev, pipe,
1081 !dir_in ? PTD_DIR_IN : PTD_DIR_OUT, NULL, 0);
1082 if (ret < 0) {
1083 DBG("control status phase error (ret = %d", ret);
1084 return -1;
1085 }
1086
1087 dev->act_len = done;
1088
1089 dump_msg(dev, pipe, buffer, len, "DEV(ret)");
1090
1091 return done;
1092}
1093
1094int submit_bulk_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
1095 int len)
1096{
1097 int dir_out = usb_pipeout(pipe);
1098 int max = max_transfer_len(dev, pipe);
1099 int done, ret;
1100
1101 DBG("--- BULK ---------------------------------------");
1102 DBG("dev=%ld pipe=%ld buf=%p size=%d dir_out=%d",
1103 usb_pipedevice(pipe), usb_pipeendpoint(pipe), buffer, len, dir_out);
1104
1105 done = 0;
1106 while (done < len) {
1107 ret = isp116x_submit_job(dev, pipe,
1108 !dir_out ? PTD_DIR_IN : PTD_DIR_OUT,
1109 (__u8 *) buffer + done,
1110 max > len - done ? len - done : max);
1111 if (ret < 0) {
1112 DBG("error on bulk message (ret = %d)", ret);
1113 return -1;
1114 }
1115
1116 done += ret;
1117
1118 if (!dir_out && ret < max) /* short packet */
1119 break;
1120 }
1121
1122 dev->act_len = done;
1123
1124 return 0;
1125}
1126
1127/* --- Basic functions ----------------------------------------------------- */
1128
1129static int isp116x_sw_reset(struct isp116x *isp116x)
1130{
1131 int retries = 15;
1132 int ret = 0;
1133
1134 DBG("");
1135
1136 isp116x->disabled = 1;
1137
1138 isp116x_write_reg16(isp116x, HCSWRES, HCSWRES_MAGIC);
1139 isp116x_write_reg32(isp116x, HCCMDSTAT, HCCMDSTAT_HCR);
1140 while (--retries) {
1141 /* It usually resets within 1 ms */
Mike Frysinger5b84dd62012-03-05 13:47:00 +00001142 mdelay(1);
Rodolfo Giometti822af352007-04-03 14:27:18 +02001143 if (!(isp116x_read_reg32(isp116x, HCCMDSTAT) & HCCMDSTAT_HCR))
1144 break;
1145 }
1146 if (!retries) {
1147 ERR("software reset timeout");
1148 ret = -1;
1149 }
1150 return ret;
1151}
1152
1153static int isp116x_reset(struct isp116x *isp116x)
1154{
1155 unsigned long t;
1156 u16 clkrdy = 0;
1157 int ret, timeout = 15 /* ms */ ;
1158
1159 DBG("");
1160
1161 ret = isp116x_sw_reset(isp116x);
1162 if (ret)
1163 return ret;
1164
1165 for (t = 0; t < timeout; t++) {
1166 clkrdy = isp116x_read_reg16(isp116x, HCuPINT) & HCuPINT_CLKRDY;
1167 if (clkrdy)
1168 break;
Mike Frysinger5b84dd62012-03-05 13:47:00 +00001169 mdelay(1);
Rodolfo Giometti822af352007-04-03 14:27:18 +02001170 }
1171 if (!clkrdy) {
1172 ERR("clock not ready after %dms", timeout);
1173 /* After sw_reset the clock won't report to be ready, if
1174 H_WAKEUP pin is high. */
1175 ERR("please make sure that the H_WAKEUP pin is pulled low!");
1176 ret = -1;
1177 }
1178 return ret;
1179}
1180
1181static void isp116x_stop(struct isp116x *isp116x)
1182{
1183 u32 val;
1184
1185 DBG("");
1186
1187 isp116x_write_reg16(isp116x, HCuPINTENB, 0);
1188
1189 /* Switch off ports' power, some devices don't come up
1190 after next 'start' without this */
1191 val = isp116x_read_reg32(isp116x, HCRHDESCA);
1192 val &= ~(RH_A_NPS | RH_A_PSM);
1193 isp116x_write_reg32(isp116x, HCRHDESCA, val);
1194 isp116x_write_reg32(isp116x, HCRHSTATUS, RH_HS_LPS);
1195
1196 isp116x_sw_reset(isp116x);
1197}
1198
1199/*
1200 * Configure the chip. The chip must be successfully reset by now.
1201 */
1202static int isp116x_start(struct isp116x *isp116x)
1203{
1204 struct isp116x_platform_data *board = isp116x->board;
1205 u32 val;
1206
1207 DBG("");
1208
1209 /* Clear interrupt status and disable all interrupt sources */
1210 isp116x_write_reg16(isp116x, HCuPINT, 0xff);
1211 isp116x_write_reg16(isp116x, HCuPINTENB, 0);
1212
1213 isp116x_write_reg16(isp116x, HCITLBUFLEN, ISP116x_ITL_BUFSIZE);
1214 isp116x_write_reg16(isp116x, HCATLBUFLEN, ISP116x_ATL_BUFSIZE);
1215
1216 /* Hardware configuration */
1217 val = HCHWCFG_DBWIDTH(1);
1218 if (board->sel15Kres)
1219 val |= HCHWCFG_15KRSEL;
1220 /* Remote wakeup won't work without working clock */
1221 if (board->remote_wakeup_enable)
1222 val |= HCHWCFG_CLKNOTSTOP;
1223 if (board->oc_enable)
1224 val |= HCHWCFG_ANALOG_OC;
1225 isp116x_write_reg16(isp116x, HCHWCFG, val);
1226
1227 /* --- Root hub configuration */
1228 val = (25 << 24) & RH_A_POTPGT;
1229 /* AN10003_1.pdf recommends RH_A_NPS (no power switching) to
1230 be always set. Yet, instead, we request individual port
1231 power switching. */
1232 val |= RH_A_PSM;
1233 /* Report overcurrent per port */
1234 val |= RH_A_OCPM;
1235 isp116x_write_reg32(isp116x, HCRHDESCA, val);
1236 isp116x->rhdesca = isp116x_read_reg32(isp116x, HCRHDESCA);
1237
1238 val = RH_B_PPCM;
1239 isp116x_write_reg32(isp116x, HCRHDESCB, val);
1240 isp116x->rhdescb = isp116x_read_reg32(isp116x, HCRHDESCB);
1241
1242 val = 0;
1243 if (board->remote_wakeup_enable)
1244 val |= RH_HS_DRWE;
1245 isp116x_write_reg32(isp116x, HCRHSTATUS, val);
1246 isp116x->rhstatus = isp116x_read_reg32(isp116x, HCRHSTATUS);
1247
1248 isp116x_write_reg32(isp116x, HCFMINTVL, 0x27782edf);
1249
1250 /* Go operational */
1251 val = HCCONTROL_USB_OPER;
1252 if (board->remote_wakeup_enable)
1253 val |= HCCONTROL_RWE;
1254 isp116x_write_reg32(isp116x, HCCONTROL, val);
1255
1256 /* Disable ports to avoid race in device enumeration */
1257 isp116x_write_reg32(isp116x, HCRHPORT1, RH_PS_CCS);
1258 isp116x_write_reg32(isp116x, HCRHPORT2, RH_PS_CCS);
1259
1260 isp116x_show_regs(isp116x);
1261
1262 isp116x->disabled = 0;
1263
1264 return 0;
1265}
1266
1267/* --- Init functions ------------------------------------------------------ */
1268
1269int isp116x_check_id(struct isp116x *isp116x)
1270{
1271 int val;
1272
1273 val = isp116x_read_reg16(isp116x, HCCHIPID);
1274 if ((val & HCCHIPID_MASK) != HCCHIPID_MAGIC) {
1275 ERR("invalid chip ID %04x", val);
1276 return -1;
1277 }
1278
1279 return 0;
1280}
1281
Troy Kisky06d513e2013-10-10 15:27:56 -07001282int usb_lowlevel_init(int index, enum usb_init_type init, void **controller))
Rodolfo Giometti822af352007-04-03 14:27:18 +02001283{
1284 struct isp116x *isp116x = &isp116x_dev;
1285
1286 DBG("");
1287
Timo Ketola785c1342007-09-24 14:50:32 +03001288 got_rhsc = rh_devnum = 0;
1289
Rodolfo Giometti822af352007-04-03 14:27:18 +02001290 /* Init device registers addr */
1291 isp116x->addr_reg = (u16 *) ISP116X_HCD_ADDR;
1292 isp116x->data_reg = (u16 *) ISP116X_HCD_DATA;
1293
1294 /* Setup specific board settings */
1295#ifdef ISP116X_HCD_SEL15kRES
1296 isp116x_board.sel15Kres = 1;
1297#endif
1298#ifdef ISP116X_HCD_OC_ENABLE
1299 isp116x_board.oc_enable = 1;
1300#endif
1301#ifdef ISP116X_HCD_REMOTE_WAKEUP_ENABLE
1302 isp116x_board.remote_wakeup_enable = 1;
1303#endif
1304 isp116x->board = &isp116x_board;
1305
1306 /* Try to get ISP116x silicon chip ID */
1307 if (isp116x_check_id(isp116x) < 0)
1308 return -1;
1309
1310 isp116x->disabled = 1;
1311 isp116x->sleeping = 0;
1312
1313 isp116x_reset(isp116x);
1314 isp116x_start(isp116x);
1315
1316 return 0;
1317}
1318
Lucas Stachc7e3b2b2012-09-26 00:14:34 +02001319int usb_lowlevel_stop(int index)
Rodolfo Giometti822af352007-04-03 14:27:18 +02001320{
1321 struct isp116x *isp116x = &isp116x_dev;
1322
1323 DBG("");
1324
1325 if (!isp116x->disabled)
1326 isp116x_stop(isp116x);
1327
1328 return 0;
1329}