blob: 3962fee7f215ddb1964205e0a99d999ff3bb4fb5 [file] [log] [blame]
York Sunee52b182012-10-11 07:13:37 +00001Overview
2--------
3The T4240QDS is a high-performance computing evaluation, development and test
4platform supporting the T4240 QorIQ™ Power Architecture™ processor. T4240QDS is
5optimized to support the high-bandwidth DDR3 memory ports, as well as the
6highly-configurable SerDes ports. The system is lead-free and RoHS-compliant.
7
8Board Features
9 SERDES Connections
10 32 lanes grouped into four 8-lane banks
11 Two “front side” banks dedicated to Ethernet
12 - High-speed crosspoint switch fabric on selected lanes
13 - Two PCI Express slots with side-band connector supporting
14 - SGMII
15 - XAUI
16 - HiGig
17 - I-pass connectors allow board-to-board and loopback support
18 Two “back side” banks dedicated to other protocols
19 - High-speed crosspoint switch fabric on all lanes
20 - Four PCI Express slots with side-band connector supporting
21 - PCI Express 3.0
22 - SATA 2.0
23 - SRIO 2.0
24 - Supports 4X Aurora debug with two connectors
25 DDR Controllers
26 Three independant 64-bit DDR3 controllers
27 Supports rates of 1866 up to 2133 MHz data-rate
28 Supports two DDR3/DDR3LP UDIMM/RDIMMs per controller
29 DDR power supplies 1.5V to all devices with automatic tracking of VTT.
30 Power software-switchable to 1.35V if software detects all DDR3LP devices.
31 MT9JSF25672AZ-2G1KZESZF has been tested at 1333, 1600, 1867, 2000 and
32 2133MT/s speeds. For 1867MT/s and above, read-to-write turnaround time
33 increases by 1 clock.
34
35 IFC/Local Bus
36 NAND flash: 8-bit, async or sync, up to 2GB.
37 NOR: 16-bit, Address/Data Multiplexed (ADM), up to 128 MB
38 NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB
39 - NOR devices support 16 virtual banks
40 GASIC: Minimal target within Qixis FPGA
41 PromJET rapid memory download support
42 Address demultiplexing handled within FPGA.
43 - Flexible demux allows 8 or 16 bit evaluation.
44 IFC Debug/Development card
45 - Support for 32-bit devices
46 Ethernet
47 Support two on-board RGMII 10/100/1G ethernet ports.
48 SGMII and XAUI support via SERDES block (see above).
49 1588 support via Symmetricom board.
50 QIXIS System Logic FPGA
51 Manages system power and reset sequencing
52 Manages DUT, board, clock, etc. configuration for dynamic shmoo
53 Collects V-I-T data in background for code/power profiling.
54 Supports legacy TMT test features (POSt, IRS, SYSCLK-synchronous assertion)
55 General fault monitoring and logging
56 Runs from ATX “hot” power rails allowing operation while system is off.
57 Clocks
58 System and DDR clock (SYSCLK, “DDRCLK”)
59 - Switch selectable to one of 16 common settings in the interval 33MHz-166MHz.
60 - Software selectable in 1MHz increments from 1-200MHz.
61 SERDES clocks
62 - Provides clocks to all SerDes blocks and slots
63 - 100, 125 and 156.25 MHz
64 Power Supplies
65 Dedicated regulators for VDD
66 - Adjustable from (0.7V to 1.3V at 80A
67 - Regulators can be controlled by VID and/or software
68 Dedicated regulator for GVDD_PL: 1.35/1.5V at 22A
69 - VTT/MVREF automatically track operating voltage
70 Dedicated regulators/filters for AVDD supplies
71 Dedicated regulators for other supplies: OVDD, BVDD, DVDD, LVDD, POVDD, etc.
72 USB
73 Supports two USB 2.0 ports with integrated PHYs
74 - One type A, one type micro-AB with 1.0A power per port.
75 Other IO
76 eSDHC/MMC
77 - SDHC card slot
78 eSPI port
79 - High-speed serial flash
80 Two Serial port
81 Four I2C ports
Shaohui Xie9bf499a2014-08-13 18:19:15 +080082 XFI
83 XFI is supported on T4QDS-XFI board which removed slot3 and routed
84 four Lanes A/B/C/D to a SFP+ cages, which to house fiber cable or
85 direct attach cable(copper), the copper cable is used to emulate
86 10GBASE-KR scenario.
87 So, for XFI usage, there are two scenarios, one will use fiber cable,
88 another will use copper cable. An hwconfig env "fsl_10gkr_copper" is
89 introduced to indicate a XFI port will use copper cable, and U-boot
90 will fixup the dtb accordingly.
91 It's used as: fsl_10gkr_copper:<10g_mac_name>
92 The <10g_mac_name> can be fm1_10g1, fm1_10g2, fm2_10g1, fm2_10g2, they
93 do not have to be coexist in hwconfig. If a MAC is listed in the env
94 "fsl_10gkr_copper", it will use copper cable, otherwise, fiber cable
95 will be used by default.
96 for ex. set "fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm2_10g1,fm2_10g2" in
97 hwconfig, then both four XFI ports will use copper cable.
98 set "fsl_10gkr_copper:fm1_10g1,fm1_10g2" in hwconfig, then first two
99 XFI ports will use copper cable, the other two XFI ports will use fiber
100 cable.
York Sunee52b182012-10-11 07:13:37 +0000101
102Memory map
103----------
104The addresses in brackets are physical addresses.
105
1060x0_0000_0000 (0x0_0000_0000) - 0x0_7fff_ffff 2GB DDR (more than 2GB is initialized but not mapped under with TLB)
1070x0_8000_0000 (0xc_0000_0000) - 0x0_dfff_ffff 1.5GB PCIE memory
Stephen George49e946c2013-03-25 07:40:12 +00001080x0_f000_0000 (0xf_0000_0000) - 0x0_f1ff_ffff 32MB DCSR (includes trace buffers)
York Sunee52b182012-10-11 07:13:37 +00001090x0_f400_0000 (0xf_f400_0000) - 0x0_f5ff_ffff 32MB BMan
1100x0_f600_0000 (0xf_f600_0000) - 0x0_f7ff_ffff 32MB QMan
1110x0_f800_0000 (0xf_f800_0000) - 0x0_f803_ffff 256KB PCIE IO
1120x0_e000_0000 (0xf_e000_0000) - 0x0_efff_ffff 256MB NOR flash
1130x0_fe00_0000 (0xf_fe00_0000) - 0x0_feff_ffff 16MB CCSR
1140x0_ffdf_0000 (0xf_ffdf_0000) - 0x0_ffdf_03ff 4KB QIXIS
1150x0_ffff_f000 (0x0_7fff_fff0) - 0x0_ffff_ffff 4KB Boot page translation for secondary cores
116
117The physical address of the last (boot page translation) varies with the actual DDR size.
York Sun0aadf4a2013-03-25 07:40:01 +0000118
119Voltage ID and VDD override
120--------------------
121T4240 has a VID feature. U-boot reads the VID efuses and adjust the voltage
122accordingly. The voltage can also be override by command vdd_override. The
123syntax is
124
125vdd_override <voltage in mV>, eg. 1050 is for 1.050v.
126
127Upon success, the actual voltage will be read back. The value is checked
128for safety and any invalid value will not adjust the voltage.
129
130Another way to override VDD is to use environmental variable, in case of using
131command is too late for some debugging. The syntax is
132
133setenv t4240qds_vdd_mv <voltage in mV>
134saveenv
135reset
136
137The override voltage takes effect when booting.
138
139Note: voltage adjustment needs to be done step by step. Changing voltage too
140rapidly may cause current surge. The voltage stepping is done by software.
141Users can set the final voltage directly.
Shaohui Xieb6036992014-04-22 15:10:44 +0800142
1432-stage NAND/SD boot loader
144-------------------------------
145PBL initializes the internal SRAM and copy SPL(160K) in SRAM.
146SPL further initialise DDR using SPD and environment variables
147and copy u-boot(768 KB) from NAND/SD device to DDR.
148Finally SPL transers control to u-boot for futher booting.
149
150SPL has following features:
151 - Executes within 256K
152 - No relocation required
153
154Run time view of SPL framework
155-------------------------------------------------
156|Area | Address |
157-------------------------------------------------
158|SecureBoot header | 0xFFFC0000 (32KB) |
159-------------------------------------------------
160|GD, BD | 0xFFFC8000 (4KB) |
161-------------------------------------------------
162|ENV | 0xFFFC9000 (8KB) |
163-------------------------------------------------
164|HEAP | 0xFFFCB000 (50KB) |
165-------------------------------------------------
166|STACK | 0xFFFD8000 (22KB) |
167-------------------------------------------------
168|U-boot SPL | 0xFFFD8000 (160KB) |
169-------------------------------------------------
170
171NAND Flash memory Map on T4QDS
172--------------------------------------------------------------
173Start End Definition Size
1740x000000 0x0FFFFF u-boot img 1MB
1750x140000 0x15FFFF u-boot env 128KB
1760x160000 0x17FFFF FMAN Ucode 128KB
177
178Micro SD Card memory Map on T4QDS
179----------------------------------------------------
180Block #blocks Definition Size
1810x008 2048 u-boot img 1MB
1820x800 0016 u-boot env 8KB
1830x820 0128 FMAN ucode 64KB
184
185Switch Settings: (ON is 1, OFF is 0)
186===============
187NAND boot SW setting:
188SW1[1:8] = 10000010
189SW2[1.1] = 0
190SW6[1:4] = 1001
191
192SD boot SW setting:
193SW1[1:8] = 00100000
194SW2[1.1] = 0