arch/arm/mach-sunxi/clock_sun6i.c

// SPDX-License-Identifier: GPL-2.0+
/*
 * sun6i specific clock code
 *
 * (C) Copyright 2007-2012
 * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
 * Tom Cubie <tangliang@allwinnertech.com>
 *
 * (C) Copyright 2013 Luke Kenneth Casson Leighton <lkcl@lkcl.net>
 */

#include <common.h>
#include <asm/io.h>
#include <asm/arch/clock.h>
#include <asm/arch/prcm.h>
#include <asm/arch/sys_proto.h>
#include <linux/delay.h>

#ifdef CONFIG_SPL_BUILD
void clock_init_safe(void)
{
	struct sunxi_ccm_reg * const ccm =
		(struct sunxi_ccm_reg *)SUNXI_CCM_BASE;

#if !defined(CONFIG_MACH_SUNXI_H3_H5) && !defined(CONFIG_MACH_SUN50I)
	struct sunxi_prcm_reg * const prcm =
		(struct sunxi_prcm_reg *)SUNXI_PRCM_BASE;

	/* Set PLL ldo voltage without this PLL6 does not work properly */
	clrsetbits_le32(&prcm->pll_ctrl1, PRCM_PLL_CTRL_LDO_KEY_MASK,
			PRCM_PLL_CTRL_LDO_KEY);
	clrsetbits_le32(&prcm->pll_ctrl1, ~PRCM_PLL_CTRL_LDO_KEY_MASK,
		PRCM_PLL_CTRL_LDO_DIGITAL_EN | PRCM_PLL_CTRL_LDO_ANALOG_EN |
		PRCM_PLL_CTRL_EXT_OSC_EN | PRCM_PLL_CTRL_LDO_OUT_L(1140));
	clrbits_le32(&prcm->pll_ctrl1, PRCM_PLL_CTRL_LDO_KEY_MASK);
#endif

#if defined(CONFIG_MACH_SUN8I_R40) || defined(CONFIG_MACH_SUN50I)
	/* Set PLL lock enable bits and switch to old lock mode */
	writel(GENMASK(12, 0), &ccm->pll_lock_ctrl);
#endif

	clock_set_pll1(408000000);

	writel(PLL6_CFG_DEFAULT, &ccm->pll6_cfg);
	while (!(readl(&ccm->pll6_cfg) & CCM_PLL6_CTRL_LOCK))
		;

	writel(AHB1_ABP1_DIV_DEFAULT, &ccm->ahb1_apb1_div);

	writel(MBUS_CLK_DEFAULT, &ccm->mbus0_clk_cfg);
	if (IS_ENABLED(CONFIG_MACH_SUN6I))
		writel(MBUS_CLK_DEFAULT, &ccm->mbus1_clk_cfg);

#if defined(CONFIG_MACH_SUN8I_R40) && defined(CONFIG_SUNXI_AHCI)
	setbits_le32(&ccm->sata_pll_cfg, CCM_SATA_PLL_DEFAULT);
	setbits_le32(&ccm->ahb_reset0_cfg, 0x1 << AHB_GATE_OFFSET_SATA);
	setbits_le32(&ccm->ahb_gate0, 0x1 << AHB_GATE_OFFSET_SATA);
	setbits_le32(&ccm->sata_clk_cfg, CCM_SATA_CTRL_ENABLE);
#endif
}
#endif

void clock_init_sec(void)
{
#ifdef CONFIG_MACH_SUNXI_H3_H5
	struct sunxi_ccm_reg * const ccm =
		(struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
	struct sunxi_prcm_reg * const prcm =
		(struct sunxi_prcm_reg *)SUNXI_PRCM_BASE;

	setbits_le32(&ccm->ccu_sec_switch,
		     CCM_SEC_SWITCH_MBUS_NONSEC |
		     CCM_SEC_SWITCH_BUS_NONSEC |
		     CCM_SEC_SWITCH_PLL_NONSEC);
	setbits_le32(&prcm->prcm_sec_switch,
		     PRCM_SEC_SWITCH_APB0_CLK_NONSEC |
		     PRCM_SEC_SWITCH_PLL_CFG_NONSEC |
		     PRCM_SEC_SWITCH_PWR_GATE_NONSEC);
#endif
}

void clock_init_uart(void)
{
#if CONFIG_CONS_INDEX < 5
	struct sunxi_ccm_reg *const ccm =
		(struct sunxi_ccm_reg *)SUNXI_CCM_BASE;

	/* uart clock source is apb2 */
	writel(APB2_CLK_SRC_OSC24M|
	       APB2_CLK_RATE_N_1|
	       APB2_CLK_RATE_M(1),
	       &ccm->apb2_div);

	/* open the clock for uart */
	setbits_le32(&ccm->apb2_gate,
		     CLK_GATE_OPEN << (APB2_GATE_UART_SHIFT +
				       CONFIG_CONS_INDEX - 1));

	/* deassert uart reset */
	setbits_le32(&ccm->apb2_reset_cfg,
		     1 << (APB2_RESET_UART_SHIFT +
			   CONFIG_CONS_INDEX - 1));
#else
	/* enable R_PIO and R_UART clocks, and de-assert resets */
	prcm_apb0_enable(PRCM_APB0_GATE_PIO | PRCM_APB0_GATE_UART);
#endif
}

#ifdef CONFIG_SPL_BUILD
void clock_set_pll1(unsigned int clk)
{
	struct sunxi_ccm_reg * const ccm =
		(struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
	const int p = 0;
	int k = 1;
	int m = 1;

	if (clk > 1152000000) {
		k = 2;
	} else if (clk > 768000000) {
		k = 4;
		m = 2;
	}

	/* Switch to 24MHz clock while changing PLL1 */
	writel(AXI_DIV_3 << AXI_DIV_SHIFT |
	       ATB_DIV_2 << ATB_DIV_SHIFT |
	       CPU_CLK_SRC_OSC24M << CPU_CLK_SRC_SHIFT,
	       &ccm->cpu_axi_cfg);

	/*
	 * sun6i: PLL1 rate = ((24000000 * n * k) >> 0) / m   (p is ignored)
	 * sun8i: PLL1 rate = ((24000000 * n * k) >> p) / m
	 */
	writel(CCM_PLL1_CTRL_EN | CCM_PLL1_CTRL_P(p) |
	       CCM_PLL1_CTRL_N(clk / (24000000 * k / m)) |
	       CCM_PLL1_CTRL_K(k) | CCM_PLL1_CTRL_M(m), &ccm->pll1_cfg);
	sdelay(200);

	/* Switch CPU to PLL1 */
	writel(AXI_DIV_3 << AXI_DIV_SHIFT |
	       ATB_DIV_2 << ATB_DIV_SHIFT |
	       CPU_CLK_SRC_PLL1 << CPU_CLK_SRC_SHIFT,
	       &ccm->cpu_axi_cfg);
}
#endif

void clock_set_pll3(unsigned int clk)
{
	struct sunxi_ccm_reg * const ccm =
		(struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
#ifdef CONFIG_SUNXI_DE2
	const int m = 4; /* 6 MHz steps to allow higher frequency for DE2 */
#else
	const int m = 8; /* 3 MHz steps just like sun4i, sun5i and sun7i */
#endif

	if (clk == 0) {
		clrbits_le32(&ccm->pll3_cfg, CCM_PLL3_CTRL_EN);
		return;
	}

	/* PLL3 rate = 24000000 * n / m */
	writel(CCM_PLL3_CTRL_EN | CCM_PLL3_CTRL_INTEGER_MODE |
	       CCM_PLL3_CTRL_N(clk / (24000000 / m)) | CCM_PLL3_CTRL_M(m),
	       &ccm->pll3_cfg);
}

#ifdef CONFIG_SUNXI_DE2
void clock_set_pll3_factors(int m, int n)
{
	struct sunxi_ccm_reg * const ccm =
		(struct sunxi_ccm_reg *)SUNXI_CCM_BASE;

	/* PLL3 rate = 24000000 * n / m */
	writel(CCM_PLL3_CTRL_EN | CCM_PLL3_CTRL_INTEGER_MODE |
	       CCM_PLL3_CTRL_N(n) | CCM_PLL3_CTRL_M(m),
	       &ccm->pll3_cfg);

	while (!(readl(&ccm->pll3_cfg) & CCM_PLL3_CTRL_LOCK))
		;
}
#endif

void clock_set_pll5(unsigned int clk, bool sigma_delta_enable)
{
	struct sunxi_ccm_reg * const ccm =
		(struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
	const int max_n = 32;
	int k = 1, m = 2;

#ifdef CONFIG_MACH_SUNXI_H3_H5
	clrsetbits_le32(&ccm->pll5_tuning_cfg, CCM_PLL5_TUN_LOCK_TIME_MASK |
			CCM_PLL5_TUN_INIT_FREQ_MASK,
			CCM_PLL5_TUN_LOCK_TIME(2) | CCM_PLL5_TUN_INIT_FREQ(16));
#endif

	if (sigma_delta_enable)
		writel(CCM_PLL5_PATTERN, &ccm->pll5_pattern_cfg);

	/* PLL5 rate = 24000000 * n * k / m */
	if (clk > 24000000 * k * max_n / m) {
		m = 1;
		if (clk > 24000000 * k * max_n / m)
			k = 2;
	}
	writel(CCM_PLL5_CTRL_EN |
	       (sigma_delta_enable ? CCM_PLL5_CTRL_SIGMA_DELTA_EN : 0) |
	       CCM_PLL5_CTRL_UPD |
	       CCM_PLL5_CTRL_N(clk / (24000000 * k / m)) |
	       CCM_PLL5_CTRL_K(k) | CCM_PLL5_CTRL_M(m), &ccm->pll5_cfg);

	udelay(5500);
}

#ifdef CONFIG_MACH_SUN6I
void clock_set_mipi_pll(unsigned int clk)
{
	struct sunxi_ccm_reg * const ccm =
		(struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
	unsigned int k, m, n, value, diff;
	unsigned best_k = 0, best_m = 0, best_n = 0, best_diff = 0xffffffff;
	unsigned int src = clock_get_pll3();

	/* All calculations are in KHz to avoid overflows */
	clk /= 1000;
	src /= 1000;

	/* Pick the closest lower clock */
	for (k = 1; k <= 4; k++) {
		for (m = 1; m <= 16; m++) {
			for (n = 1; n <= 16; n++) {
				value = src * n * k / m;
				if (value > clk)
					continue;

				diff = clk - value;
				if (diff < best_diff) {
					best_diff = diff;
					best_k = k;
					best_m = m;
					best_n = n;
				}
				if (diff == 0)
					goto done;
			}
		}
	}

done:
	writel(CCM_MIPI_PLL_CTRL_EN | CCM_MIPI_PLL_CTRL_LDO_EN |
	       CCM_MIPI_PLL_CTRL_N(best_n) | CCM_MIPI_PLL_CTRL_K(best_k) |
	       CCM_MIPI_PLL_CTRL_M(best_m), &ccm->mipi_pll_cfg);
}
#endif

#ifdef CONFIG_SUNXI_DE2
void clock_set_pll10(unsigned int clk)
{
	struct sunxi_ccm_reg * const ccm =
		(struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
	const int m = 2; /* 12 MHz steps */

	if (clk == 0) {
		clrbits_le32(&ccm->pll10_cfg, CCM_PLL10_CTRL_EN);
		return;
	}

	/* PLL10 rate = 24000000 * n / m */
	writel(CCM_PLL10_CTRL_EN | CCM_PLL10_CTRL_INTEGER_MODE |
	       CCM_PLL10_CTRL_N(clk / (24000000 / m)) | CCM_PLL10_CTRL_M(m),
	       &ccm->pll10_cfg);

	while (!(readl(&ccm->pll10_cfg) & CCM_PLL10_CTRL_LOCK))
		;
}
#endif

#if defined(CONFIG_MACH_SUN8I_A33) || \
    defined(CONFIG_MACH_SUN8I_R40) || \
    defined(CONFIG_MACH_SUN50I)
void clock_set_pll11(unsigned int clk, bool sigma_delta_enable)
{
	struct sunxi_ccm_reg * const ccm =
		(struct sunxi_ccm_reg *)SUNXI_CCM_BASE;

	if (sigma_delta_enable)
		writel(CCM_PLL11_PATTERN, &ccm->pll11_pattern_cfg0);

	writel(CCM_PLL11_CTRL_EN | CCM_PLL11_CTRL_UPD |
	       (sigma_delta_enable ? CCM_PLL11_CTRL_SIGMA_DELTA_EN : 0) |
	       CCM_PLL11_CTRL_N(clk / 24000000), &ccm->pll11_cfg);

	while (readl(&ccm->pll11_cfg) & CCM_PLL11_CTRL_UPD)
		;
}
#endif

unsigned int clock_get_pll3(void)
{
	struct sunxi_ccm_reg *const ccm =
		(struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
	uint32_t rval = readl(&ccm->pll3_cfg);
	int n = ((rval & CCM_PLL3_CTRL_N_MASK) >> CCM_PLL3_CTRL_N_SHIFT) + 1;
	int m = ((rval & CCM_PLL3_CTRL_M_MASK) >> CCM_PLL3_CTRL_M_SHIFT) + 1;

	/* Multiply by 1000 after dividing by m to avoid integer overflows */
	return (24000 * n / m) * 1000;
}

unsigned int clock_get_pll6(void)
{
	struct sunxi_ccm_reg *const ccm =
		(struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
	uint32_t rval = readl(&ccm->pll6_cfg);
	int n = ((rval & CCM_PLL6_CTRL_N_MASK) >> CCM_PLL6_CTRL_N_SHIFT) + 1;
	int k = ((rval & CCM_PLL6_CTRL_K_MASK) >> CCM_PLL6_CTRL_K_SHIFT) + 1;
	return 24000000 * n * k / 2;
}

unsigned int clock_get_mipi_pll(void)
{
	struct sunxi_ccm_reg *const ccm =
		(struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
	uint32_t rval = readl(&ccm->mipi_pll_cfg);
	unsigned int n = ((rval & CCM_MIPI_PLL_CTRL_N_MASK) >> CCM_MIPI_PLL_CTRL_N_SHIFT) + 1;
	unsigned int k = ((rval & CCM_MIPI_PLL_CTRL_K_MASK) >> CCM_MIPI_PLL_CTRL_K_SHIFT) + 1;
	unsigned int m = ((rval & CCM_MIPI_PLL_CTRL_M_MASK) >> CCM_MIPI_PLL_CTRL_M_SHIFT) + 1;
	unsigned int src = clock_get_pll3();

	/* Multiply by 1000 after dividing by m to avoid integer overflows */
	return ((src / 1000) * n * k / m) * 1000;
}

void clock_set_de_mod_clock(u32 *clk_cfg, unsigned int hz)
{
	int pll = clock_get_pll6() * 2;
	int div = 1;

	while ((pll / div) > hz)
		div++;

	writel(CCM_DE_CTRL_GATE | CCM_DE_CTRL_PLL6_2X | CCM_DE_CTRL_M(div),
	       clk_cfg);
}