include/configs/dra7xx_evm.h

/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * (C) Copyright 2013
 * Texas Instruments Incorporated.
 * Lokesh Vutla	  <lokeshvutla@ti.com>
 *
 * Configuration settings for the TI DRA7XX board.
 * See ti_omap5_common.h for omap5 common settings.
 */

#ifndef __CONFIG_DRA7XX_EVM_H
#define __CONFIG_DRA7XX_EVM_H

#include <environment/ti/dfu.h>

#define CONFIG_IODELAY_RECALIBRATION

#define CONFIG_VERY_BIG_RAM
#define CONFIG_MAX_MEM_MAPPED		0x80000000

#ifndef CONFIG_QSPI_BOOT
/* MMC ENV related defines */
#define CONFIG_SYS_MMC_ENV_DEV		1	/* SLOT2: eMMC(1) */
#endif

#if (CONFIG_CONS_INDEX == 1)
#define CONSOLEDEV			"ttyS0"
#elif (CONFIG_CONS_INDEX == 3)
#define CONSOLEDEV			"ttyS2"
#endif
#define CONFIG_SYS_NS16550_COM1		UART1_BASE	/* Base EVM has UART0 */
#define CONFIG_SYS_NS16550_COM2		UART2_BASE	/* UART2 */
#define CONFIG_SYS_NS16550_COM3		UART3_BASE	/* UART3 */

#define CONFIG_ENV_EEPROM_IS_ON_I2C
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* Main EEPROM */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2

#define CONFIG_SYS_OMAP_ABE_SYSCK

#ifndef CONFIG_SPL_BUILD
#define DFUARGS \
	"dfu_bufsiz=0x10000\0" \
	DFU_ALT_INFO_MMC \
	DFU_ALT_INFO_EMMC \
	DFU_ALT_INFO_RAM \
	DFU_ALT_INFO_QSPI
#endif

#ifdef CONFIG_SPL_BUILD
#undef CONFIG_CMD_BOOTD
#ifdef CONFIG_SPL_DFU
#define CONFIG_SPL_LOAD_FIT_ADDRESS 0x80200000
#define DFUARGS \
	"dfu_bufsiz=0x10000\0" \
	DFU_ALT_INFO_RAM
#endif
#endif

#include <configs/ti_omap5_common.h>

/* Enhance our eMMC support / experience. */
#define CONFIG_HSMMC2_8BIT

/* CPSW Ethernet */
#define CONFIG_BOOTP_SEND_HOSTNAME
#define CONFIG_NET_RETRY_COUNT		10

/*
 * Default to using SPI for environment, etc.
 * 0x000000 - 0x040000 : QSPI.SPL (256KiB)
 * 0x040000 - 0x140000 : QSPI.u-boot (1MiB)
 * 0x140000 - 0x1C0000 : QSPI.u-boot-spl-os (512KiB)
 * 0x1C0000 - 0x1D0000 : QSPI.u-boot-env (64KiB)
 * 0x1D0000 - 0x1E0000 : QSPI.u-boot-env.backup1 (64KiB)
 * 0x1E0000 - 0x9E0000 : QSPI.kernel (8MiB)
 * 0x9E0000 - 0x2000000 : USERLAND
 */
#define CONFIG_SYS_SPI_KERNEL_OFFS	0x1E0000
#define CONFIG_SYS_SPI_ARGS_OFFS	0x140000
#define CONFIG_SYS_SPI_ARGS_SIZE	0x80000

/* SPI SPL */

/* USB xHCI HOST */
#define CONFIG_USB_XHCI_OMAP

#define CONFIG_OMAP_USB2PHY2_HOST

/* SATA */
#define CONFIG_SCSI_AHCI_PLAT

/* NAND support */
#ifdef CONFIG_MTD_RAW_NAND
/* NAND: device related configs */
#define CONFIG_SYS_NAND_PAGE_SIZE	2048
#define CONFIG_SYS_NAND_OOBSIZE		64
#define CONFIG_SYS_NAND_BLOCK_SIZE	(128*1024)
#define CONFIG_SYS_NAND_PAGE_COUNT	(CONFIG_SYS_NAND_BLOCK_SIZE / \
					 CONFIG_SYS_NAND_PAGE_SIZE)
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
/* NAND: driver related configs */
#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_BCH8_CODE_HW
#define CONFIG_SYS_NAND_BAD_BLOCK_POS	NAND_LARGE_BADBLOCK_POS
#define CONFIG_SYS_NAND_ECCPOS		{ 2, 3, 4, 5, 6, 7, 8, 9, \
					 10, 11, 12, 13, 14, 15, 16, 17, \
					 18, 19, 20, 21, 22, 23, 24, 25, \
					 26, 27, 28, 29, 30, 31, 32, 33, \
					 34, 35, 36, 37, 38, 39, 40, 41, \
					 42, 43, 44, 45, 46, 47, 48, 49, \
					 50, 51, 52, 53, 54, 55, 56, 57, }
#define CONFIG_SYS_NAND_ECCSIZE		512
#define CONFIG_SYS_NAND_ECCBYTES	14
#define CONFIG_SYS_NAND_U_BOOT_OFFS	0x00140000
/* NAND: SPL related configs */
/* NAND: SPL falcon mode configs */
#ifdef CONFIG_SPL_OS_BOOT
#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS	0x00200000 /* kernel offset */
#endif
#endif /* !CONFIG_MTD_RAW_NAND */

/* Parallel NOR Support */
#if defined(CONFIG_NOR)
/* NOR: device related configs */
#define CONFIG_SYS_MAX_FLASH_SECT	512
#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
#define CONFIG_SYS_FLASH_SIZE		(64 * 1024 * 1024) /* 64 MB */
/* #define CONFIG_INIT_IGNORE_ERROR */
#define CONFIG_SYS_MAX_FLASH_BANKS	1
#define CONFIG_SYS_FLASH_BASE		(0x08000000)
#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
/* Reduce SPL size by removing unlikey targets */
#endif  /* NOR support */

#endif /* __CONFIG_DRA7XX_EVM_H */