blob: 46dae556f7b88c638e39993217961c0f155b8eff [file] [log] [blame]
Adam Ford063da122017-04-17 08:09:43 -05001/*
2 * This program is free software; you can redistribute it and/or modify
3 * it under the terms of the GNU General Public License version 2 as
4 * published by the Free Software Foundation.
5 */
6
7#include <dt-bindings/input/input.h>
8
9/ {
10 cpus {
11 cpu@0 {
12 cpu0-supply = <&vcc>;
13 };
14 };
15
16 memory@80000000 {
17 device_type = "memory";
18 reg = <0x80000000 0>;
19 };
20
21 wl12xx_vmmc: wl12xx_vmmc {
22 compatible = "regulator-fixed";
23 regulator-name = "vwl1271";
24 regulator-min-microvolt = <1800000>;
25 regulator-max-microvolt = <1800000>;
26 gpio = <&gpio1 3 0>; /* gpio_3 */
27 startup-delay-us = <70000>;
28 enable-active-high;
29 vin-supply = <&vmmc2>;
30 };
31
32 /* HS USB Host PHY on PORT 1 */
33 hsusb2_phy: hsusb2_phy {
34 compatible = "usb-nop-xceiv";
35 reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
36 };
37};
38
39&gpmc {
40 ranges = <0 0 0x00000000 0x1000000>; /* CS0: 16MB for NAND */
41
42 nand@0,0 {
43 compatible = "ti,omap2-nand";
44 reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
45 interrupt-parent = <&gpmc>;
46 interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
47 <1 IRQ_TYPE_NONE>; /* termcount */
48 linux,mtd-name = "micron,mt29f4g16abbda3w";
49 nand-bus-width = <16>;
50 ti,nand-ecc-opt = "bch8";
51 rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
52 gpmc,sync-clk-ps = <0>;
53 gpmc,cs-on-ns = <0>;
54 gpmc,cs-rd-off-ns = <44>;
55 gpmc,cs-wr-off-ns = <44>;
56 gpmc,adv-on-ns = <6>;
57 gpmc,adv-rd-off-ns = <34>;
58 gpmc,adv-wr-off-ns = <44>;
59 gpmc,we-off-ns = <40>;
60 gpmc,oe-off-ns = <54>;
61 gpmc,access-ns = <64>;
62 gpmc,rd-cycle-ns = <82>;
63 gpmc,wr-cycle-ns = <82>;
64 gpmc,wr-access-ns = <40>;
65 gpmc,wr-data-mux-bus-ns = <0>;
66 gpmc,device-width = <2>;
67 #address-cells = <1>;
68 #size-cells = <1>;
69
70 /* u-boot uses mtdparts=omap2-nand.0:512k(x-loader),1920k(u-boot),128k(u-boot-env),4m(kernel),-(fs) */
71
72 x-loader@0 {
73 label = "x-loader";
74 reg = <0 0x80000>;
75 };
76
77 bootloaders@80000 {
78 label = "u-boot";
79 reg = <0x80000 0x1e0000>;
80 };
81
82 bootloaders_env@260000 {
83 label = "u-boot-env";
84 reg = <0x260000 0x20000>;
85 };
86
87 kernel@280000 {
88 label = "kernel";
89 reg = <0x280000 0x400000>;
90 };
91
92 filesystem@680000 {
93 label = "fs";
94 reg = <0x680000 0>; /* 0 = MTDPART_SIZ_FULL */
95 };
96 };
97};
98
99&i2c1 {
100 clock-frequency = <400000>;
101
102 twl: twl@48 {
103 reg = <0x48>;
104 interrupts = <7>; /* SYS_NIRQ cascaded to intc */
105 interrupt-parent = <&intc>;
106 twl_audio: audio {
107 compatible = "ti,twl4030-audio";
108 codec {
109 };
110 };
111 };
112};
113
114&i2c2 {
115 clock-frequency = <400000>;
116};
117
118&i2c3 {
119 clock-frequency = <400000>;
120};
121
122&mmc3 {
123 interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
124 pinctrl-0 = <&mmc3_pins>;
125 pinctrl-names = "default";
126 vmmc-supply = <&wl12xx_vmmc>;
127 non-removable;
128 bus-width = <4>;
129 cap-power-off-card;
130 #address-cells = <1>;
131 #size-cells = <0>;
132 wlcore: wlcore@2 {
133 compatible = "ti,wl1273";
134 reg = <2>;
135 interrupt-parent = <&gpio5>;
136 interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
137 ref-clock-frequency = <26000000>;
138 };
139};
140
141&usbhshost {
142 port2-mode = "ehci-phy";
143};
144
145&usbhsehci {
146 phys = <0 &hsusb2_phy>;
147};
148
149
150&omap3_pmx_core {
151 pinctrl-names = "default";
152 pinctrl-0 = <&hsusb2_pins>;
153
154 mmc3_pins: pinmux_mm3_pins {
155 pinctrl-single,pins = <
156 OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */
157 OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */
158 OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */
159 OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */
160 OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */
161 OMAP3_CORE1_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4) /* sys_boot1.gpio_3 */
162 OMAP3_CORE1_IOPAD(0x21d0, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.sdmmc3_cmd */
163 OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs2.sdmmc_clk */
164 >;
165 };
166 mcbsp2_pins: pinmux_mcbsp2_pins {
167 pinctrl-single,pins = <
168 OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */
169 OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0) /* mcbsp2_clkx */
170 OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0) /* mcbsp2_dr */
171 OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0) /* mcbsp2_dx */
172 >;
173 };
174 uart2_pins: pinmux_uart2_pins {
175 pinctrl-single,pins = <
176 OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0) /* uart2_cts.uart2_cts */
177 OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts .uart2_rts*/
178 OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */
179 OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */
180 OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* GPIO_162,BT_EN */
181 >;
182 };
183 mcspi1_pins: pinmux_mcspi1_pins {
184 pinctrl-single,pins = <
185 OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */
186 OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */
187 OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
188 OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */
189 >;
190 };
191
192 hsusb2_pins: pinmux_hsusb2_pins {
193 pinctrl-single,pins = <
194 OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
195 OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
196 OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
197 OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
198 OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
199 OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
200 >;
201 };
202
203 hsusb_otg_pins: pinmux_hsusb_otg_pins {
204 pinctrl-single,pins = <
205 OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */
206 OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */
207 OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */
208 OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */
209 OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */
210 OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */
211 OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */
212 OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */
213 OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */
214 OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */
215 OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */
216 OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */
217 >;
218 };
219
220
221};
222
223&omap3_pmx_wkup {
224 pinctrl-names = "default";
225 pinctrl-0 = <&hsusb2_reset_pin>;
226 hsusb2_reset_pin: pinmux_hsusb1_reset_pin {
227 pinctrl-single,pins = <
228 OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */
229 >;
230 };
231};
232
233&omap3_pmx_core2 {
234 pinctrl-names = "default";
235 pinctrl-0 = <&hsusb2_2_pins>;
236 hsusb2_2_pins: pinmux_hsusb2_2_pins {
237 pinctrl-single,pins = <
238 OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
239 OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
240 OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
241 OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
242 OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
243 OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
244 >;
245 };
246};
247
248&uart2 {
249 interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
250 pinctrl-names = "default";
251 pinctrl-0 = <&uart2_pins>;
252};
253
254&mcspi1 {
255 pinctrl-names = "default";
256 pinctrl-0 = <&mcspi1_pins>;
257};
258
259#include "twl4030.dtsi"
260#include "twl4030_omap3.dtsi"
261
262&twl {
263 twl_power: power {
264 compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle";
265 ti,use_poweroff;
266 };
267};
268
269&twl_gpio {
270 ti,use-leds;
271};