blob: 01597b965b6ce16e2584b640eee76336050988d8 [file] [log] [blame]
Kyle Moffettf8bbb4d2011-12-07 16:39:16 -05001/*
2 * Copyright 2009-2010 eXMeritus, A Boeing Company
3 *
4 * See file CREDITS for list of people who contributed to this
5 * project.
6 *
7 * This program is free software; you can redistribute it and/or
8 * modify it under the terms of the GNU General Public License as
9 * published by the Free Software Foundation; either version 2 of
10 * the License, or (at your option) any later version.
11 *
12 * This program is distributed in the hope that it will be useful,
13 * but WITHOUT ANY WARRANTY; without even the implied warranty of
14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
15 * GNU General Public License for more details.
16 *
17 * You should have received a copy of the GNU General Public License
18 * along with this program; if not, write to the Free Software
19 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
20 * MA 02111-1307 USA
21 */
22
23/*
24 * HardwareWall HWW-1U-1A airborne unit configuration file
25 */
26#ifndef __CONFIG_H
27#define __CONFIG_H
28
29/* High-level system configuration options */
30#define CONFIG_BOOKE /* Power/PowerPC Book-E */
31#define CONFIG_E500 /* e500 (Power ISA v2.03 with SPE) */
32#define CONFIG_MPC85xx /* MPC8540/60/55/41/48 family */
33#define CONFIG_FSL_ELBC /* FreeScale Enhanced LocalBus Cntlr */
34#define CONFIG_FSL_LAW /* FreeScale Local Access Window */
35#define CONFIG_P2020 /* FreeScale P2020 */
36#define CONFIG_HWW1U1A /* eXMeritus HardwareWall HWW-1U-1A */
37#define CONFIG_MP /* Multiprocessing support */
38#define CONFIG_HWCONFIG /* Use hwconfig from environment */
39
40#define CONFIG_L2_CACHE /* L2 cache enabled */
41#define CONFIG_BTB /* Branch predition enabled */
42
43#define CONFIG_PANIC_HANG /* No board reset on panic */
44#define CONFIG_BOARD_EARLY_INIT_R /* Call board_early_init_r() */
45#define CONFIG_CMD_REGINFO /* Dump various CPU regs */
46
47/*
48 * Allow the use of 36-bit physical addresses. Device-trees with 64-bit
49 * addresses have known compatibility issues with some existing kernels.
50 */
51#define CONFIG_ENABLE_36BIT_PHYS
52#define CONFIG_PHYS_64BIT
53#define CONFIG_ADDR_MAP
54#define CONFIG_SYS_NUM_ADDR_MAP 16 /* Number of entries in TLB1 */
55
56/* Reserve plenty of RAM for malloc (we have 2GB+) */
57#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
58
59/* How much L2 cache do we map so we can use it as RAM */
60#define CONFIG_SYS_INIT_RAM_LOCK
61#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
62
63/* This is our temporary global data area just above the stack */
64#define CONFIG_SYS_GBL_DATA_OFFSET \
65 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
66
67/* The stack grows down from the global data area */
68#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
69
70/* Enable IRQs and watchdog with a 1000Hz system decrementer */
71#define CONFIG_CMD_IRQ
72#define CONFIG_SYS_HZ 1000
73
74
75/* -------------------------------------------------------------------- */
76
77/*
78 * Clock crystal configuration:
79 * (1) SYS: 66.666MHz +/- 50ppm (drives CPU/PCI/DDR)
80 * (2) CCB: Multiplier from SYS_CLK
81 * (3) RTC: 25.000MHz +/- 50ppm (sampled against CCB clock)
82 */
83#define CONFIG_SYS_CLK_FREQ 66666000/*Hz*/
84#define CONFIG_DDR_CLK_FREQ 66666000/*Hz*/
85
86
87/* -------------------------------------------------------------------- */
88
89/*
90 * Memory map
91 *
92 * 0x0000_0000 0x7fff_ffff 2G DDR2 ECC SDRAM
93 * 0x8000_0000 0x9fff_ffff 512M PCI-E Bus 1
94 * 0xa000_0000 0xbfff_ffff 512M PCI-E Bus 2 (unused)
95 * 0xc000_0000 0xdfff_ffff 512M PCI-E Bus 3
96 * 0xe000_0000 0xe7ff_ffff 128M Spansion FLASH
97 * 0xe800_0000 0xefff_ffff 128M Spansion FLASH
98 * 0xffd0_0000 0xffd0_3fff 16K L1 boot stack (TLB0)
99 * 0xffe0_0000 0xffef_ffff 1M CCSR
100 * 0xffe0_5000 0xffe0_5fff 4K Enhanced LocalBus Controller
101 */
102
103/* Virtual Memory Map */
104#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
105#define CONFIG_SYS_SDRAM_BASE 0x00000000
106#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
107#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
108#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
109#define CONFIG_SYS_FLASH_BASE 0xe0000000
110#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000
111#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
112#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000
113#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000
114#define CONFIG_SYS_CCSRBAR 0xffe00000 /* CCSRBAR @ runtime */
115
116#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
117#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
118#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
119#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
120#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
121#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
122
123/* Physical Memory Map */
124#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc00000000ull
125#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
126#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc40000000ull
127#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull
128#define CONFIG_SYS_PCIE3_IO_PHYS 0xfffc00000ull
129#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull
130#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc20000ull
131#define CONFIG_SYS_INIT_RAM_ADDR_PHYS 0xfffd00000ull
132#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf /* for ASM code */
133#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xffd00000 /* for ASM code */
134#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0xf /* for ASM code */
135#define CONFIG_SYS_CCSRBAR_PHYS_LOW 0xffe00000 /* for ASM code */
136
137
138/* -------------------------------------------------------------------- */
139
140/* U-Boot image (MONITOR_BASE == TEXT_BASE) */
141#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc /* Top address in flash */
142#define CONFIG_SYS_TEXT_BASE 0xeff80000 /* Start of U-Boot image */
143#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
144#define CONFIG_SYS_MONITOR_LEN 0x80000 /* 512kB (4 flash sectors) */
145
146/*
147 * U-Boot Environment Image: The two sectors immediately below U-Boot
148 * form the U-Boot environment (regular and redundant).
149 */
150#define CONFIG_ENV_IS_IN_FLASH /* The environment image is stored in FLASH */
151#define CONFIG_ENV_OVERWRITE /* Allow "protected" variables to be erased */
152#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128kB (1 flash sector) */
153#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
154#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE)
155
156/* Only use 8kB of each environment sector for data */
157#define CONFIG_ENV_SIZE 0x2000 /* 8kB */
158#define CONFIG_ENV_SIZE_REDUND 0x2000 /* 8kB */
159
160
161/* -------------------------------------------------------------------- */
162
163/* Serial Console Configuration */
164#define CONFIG_CONS_INDEX 1
165#define CONFIG_SYS_NS16550
166#define CONFIG_SYS_NS16550_SERIAL
167#define CONFIG_SYS_NS16550_REG_SIZE 1
168#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
169
170#define CONFIG_BAUDRATE 115200
171#define CONFIG_SYS_BAUDRATE_TABLE \
172 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
173
174#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
175#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
176
177/* Echo back characters received during a serial download */
178#define CONFIG_LOADS_ECHO
179
180/* Allow a serial-download to temporarily change baud */
181#define CONFIG_SYS_LOADS_BAUD_CHANGE
182
183
184/* -------------------------------------------------------------------- */
185
186/* PCI and PCI-Express Support */
187#define CONFIG_PCI /* Enable PCI/PCIE */
188#define CONFIG_PCI_PNP /* Scan PCI busses */
189#define CONFIG_CMD_PCI /* Enable the "pci" command */
190#define CONFIG_FSL_PCI_INIT /* Common FreeScale PCI initialization */
191#define CONFIG_FSL_PCIE_RESET /* We have PCI-E reset errata */
192#define CONFIG_SYS_PCI_64BIT /* PCI resources are 64-bit */
193#define CONFIG_PCI_SCAN_SHOW /* Display PCI scan during boot */
194
195/* Enable 2 of the 3 PCI-E controllers */
196#define CONFIG_PCIE3
197#undef CONFIG_PCIE2
198#define CONFIG_PCIE1
199
200/* Display human-readable names when initializing */
201#define CONFIG_SYS_PCIE3_NAME "Intel 82571EB"
202#define CONFIG_SYS_PCIE2_NAME "Unused"
203#define CONFIG_SYS_PCIE1_NAME "Silicon Image SIL3531"
204
205/*
206 * PCI bus addresses
207 * Memory space is mapped 1-1, but I/O space must start from 0.
208 */
209#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
210#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
211#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
212#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
213#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
214#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
215
216
217/* -------------------------------------------------------------------- */
218
219/* Generic FreeScale hardware I2C support */
220#define CONFIG_HARD_I2C
221#define CONFIG_FSL_I2C
222#define CONFIG_CMD_I2C
223#define CONFIG_I2C_MULTI_BUS
224#define CONFIG_SYS_I2C_OFFSET 0x3000
225#define CONFIG_SYS_I2C2_OFFSET 0x3100
226
227/* I2C bus configuration */
228#define CONFIG_SYS_I2C_SPEED 400000
229#define CONFIG_SYS_I2C_SLAVE 0x7F
230
231/* DDR2 SO-RDIMM SPD EEPROM is at I2C0-0x51 */
232#define CONFIG_SYS_SPD_BUS_NUM 0
233#define SPD_EEPROM_ADDRESS 0x51
234
235/* DS1339 RTC is at I2C0-0x68 (I know it says "DS1337", it's a DS1339) */
236#define CONFIG_CMD_DATE
237#define CONFIG_RTC_DS1337
238#define CONFIG_SYS_RTC_BUS_NUM 0
239#define CONFIG_SYS_I2C_RTC_ADDR 0x68
240/* Turn off RTC square-wave output to save battery */
241#define CONFIG_SYS_RTC_DS1337_NOOSC
242
Kyle Moffett0ecb5512011-12-15 22:26:52 -0500243/*
244 * AT24C128N EEPROM at I2C0-0x53.
245 *
246 * That Atmel EEPROM has 128kbit of memory (16kByte) divided into 256 pages
247 * of 64 bytes per page. The chip uses 2-byte addresses and has a max write
248 * cycle time of 20ms according to the datasheet.
249 *
250 * NOTE: Our environment is stored on regular direct-attached FLASH, this
251 * chip is only used as a write-protected backup for certain key settings
252 * such as the serial# and macaddr values. (EG: "env import")
253 */
254#define CONFIG_CMD_EEPROM
255#define CONFIG_ENV_EEPROM_IS_ON_I2C
256#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53
257#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
258#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 1 << 6 == 64 byte pages */
259#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 21
260
261/*
262 * PCA9554 is at I2C1-0x3f (I know it says "PCA953X", it's a PCA9554). You
263 * must first select the I2C1 bus with "i2c dev 1" or the "pca953x" command
264 * will not be able to access the chip.
265 */
Kyle Moffettf8bbb4d2011-12-07 16:39:16 -0500266#define CONFIG_PCA953X
267#define CONFIG_CMD_PCA953X
268#define CONFIG_CMD_PCA953X_INFO
269#define CONFIG_SYS_I2C_PCA953X_ADDR 0x3f
270
271
272/* -------------------------------------------------------------------- */
273
274/* FreeScale DDR2/3 SDRAM Controller */
275#define CONFIG_FSL_DDR2 /* Our SDRAM slot is DDR2 */
276#define CONFIG_DDR_ECC /* Enable ECC by default */
277#define CONFIG_DDR_SPD /* Detect DDR config from SPD EEPROM */
278#define CONFIG_SPD_EEPROM /* ...why 2 config variables for this? */
279#define CONFIG_VERY_BIG_RAM /* Allow 2GB+ of RAM */
280#define CONFIG_CMD_SDRAM
281
282/* Standard P2020 DDR controller parameters */
283#define CONFIG_NUM_DDR_CONTROLLERS 1
284#define CONFIG_DIMM_SLOTS_PER_CTLR 1
285#define CONFIG_CHIP_SELECTS_PER_CTRL 2
286
287/* Make sure to tell the DDR controller to preinitialze all of RAM */
288#define CONFIG_MEM_INIT_VALUE 0xDEADBEEF
289#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
290
291
292/* -------------------------------------------------------------------- */
293
294/* FLASH Memory Configuration (2x 128MB SPANSION FLASH) */
295#define CONFIG_FLASH_CFI_DRIVER
296#define CONFIG_SYS_FLASH_CFI
297#define CONFIG_SYS_FLASH_EMPTY_INFO
298#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
299
300/* Flash banks (2x 128MB) */
301#define FLASH0_PHYS (CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000ull)
302#define FLASH1_PHYS (CONFIG_SYS_FLASH_BASE_PHYS + 0x0000000ull)
303#define CONFIG_SYS_MAX_FLASH_BANKS 2
304#define CONFIG_SYS_MAX_FLASH_SECT 1024
305#define CONFIG_SYS_FLASH_BANKS_LIST { FLASH0_PHYS, FLASH1_PHYS }
306
307/*
308 * Flash access modes and timings (values are the defaults after a RESET).
309 *
310 * NOTE: These could probably be optimized but are more than sufficient for
311 * this particular system for the moment.
312 */
313#define FLASH_BRx (BR_PS_16 | BR_MS_GPCM | BR_V)
314#define FLASH_ORx (OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | OR_GPCM_XACS \
315 | OR_GPCM_SCY_15 | OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
316
317/* Configure both flash banks */
318#define CONFIG_SYS_BR0_PRELIM (FLASH_BRx | BR_PHYS_ADDR(FLASH0_PHYS))
319#define CONFIG_SYS_BR1_PRELIM (FLASH_BRx | BR_PHYS_ADDR(FLASH1_PHYS))
320#define CONFIG_SYS_OR0_PRELIM (FLASH_ORx | OR_AM_128MB)
321#define CONFIG_SYS_OR1_PRELIM (FLASH_ORx | OR_AM_128MB)
322
323/* Flash timeouts (in ms) */
324#define CONFIG_SYS_FLASH_ERASE_TOUT 60000UL /* Erase (60s) */
325#define CONFIG_SYS_FLASH_WRITE_TOUT 500UL /* Write (0.5s) */
326
327/* Quiet flash testing */
328#define CONFIG_SYS_FLASH_QUIET_TEST
329
330/* Make program/erase count down from 45/5 (9....8....7....) */
331#define CONFIG_FLASH_SHOW_PROGRESS 45
332
333
334/* -------------------------------------------------------------------- */
335
336/* Ethernet Device Support */
337#define CONFIG_MII /* Enable MII PHY code */
338#define CONFIG_MII_DEFAULT_TSEC /* ??? Copied from P2020DS */
339#define CONFIG_PHY_GIGE /* Support Gigabit PHYs */
340#define CONFIG_ETHPRIME "e1000#0" /* Default to external ports */
341
342/* Turn on various helpful networking commands */
343#define CONFIG_CMD_DHCP
344#define CONFIG_CMD_MII
345#define CONFIG_CMD_NET
346#define CONFIG_CMD_PING
347
348/* On-chip FreeScale P2020 "tsec" Ethernet (oneway fibers and peer) */
349#define CONFIG_TSEC_ENET
350#define CONFIG_TSEC1
351#define CONFIG_TSEC2
352#define CONFIG_TSEC3
353#define CONFIG_TSEC1_NAME "owt0"
354#define CONFIG_TSEC2_NAME "owt1"
355#define CONFIG_TSEC3_NAME "peer"
356#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
357#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
358#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
359#define TSEC1_PHYIDX 0
360#define TSEC2_PHYIDX 0
361#define TSEC3_PHYIDX 0
362#define TSEC1_PHY_ADDR 2
363#define TSEC2_PHY_ADDR 3
364#define TSEC3_PHY_ADDR 4
365#define TSEC3_PHY_ADDR_CPUA 4
366#define TSEC3_PHY_ADDR_CPUB 5
367
368/* PCI-E dual-port E1000 (external ethernet ports) */
369#define CONFIG_E1000
370#define CONFIG_E1000_SPI
371#define CONFIG_E1000_SPI_GENERIC
372#define CONFIG_CMD_E1000
373
374/* We need the SPI infrastructure to poke the E1000's EEPROM */
375#define CONFIG_SPI
376#define CONFIG_SPI_X
377#define CONFIG_CMD_SPI
378#define MAX_SPI_BYTES 32
379
380
381/* -------------------------------------------------------------------- */
382
383/* USB Thumbdrive Device Support */
384#define CONFIG_USB_EHCI
385#define CONFIG_USB_EHCI_FSL
386#define CONFIG_USB_STORAGE
387#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
388#define CONFIG_CMD_USB
389
390/* Partition and Filesystem support */
391#define CONFIG_DOS_PARTITION
392#define CONFIG_EFI_PARTITION
393#define CONFIG_ISO_PARTITION
394#define CONFIG_CMD_EXT2
395#define CONFIG_CMD_FAT
396
397
398/* -------------------------------------------------------------------- */
399
400/* Command line configuration. */
401#define CONFIG_CMDLINE_EDITING /* Enable command editing */
402#define CONFIG_COMMAND_HISTORY /* Enable command history */
403#define CONFIG_AUTO_COMPLETE /* Enable command completion */
404#define CONFIG_SYS_LONGHELP /* Enable detailed command help */
405#define CONFIG_SYS_MAXARGS 128 /* Up to 128 command-line args */
406#define CONFIG_SYS_PBSIZE 8192 /* Allow up to 8k printed lines */
407#define CONFIG_SYS_CBSIZE 4096 /* Allow up to 4k command lines */
408#define CONFIG_SYS_BARGSIZE 4096 /* Allow up to 4k boot args */
409#define CONFIG_SYS_HUSH_PARSER /* Enable a fancier shell */
410#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " /* Command-line continuation */
411
412/* A little extra magic here for the prompt */
413#define CONFIG_SYS_PROMPT hww1u1a_get_ps1()
414#ifndef __ASSEMBLY__
415const char *hww1u1a_get_ps1(void);
416#endif
417
418/* Include a bunch of default commands we probably want */
419#include <config_cmd_default.h>
420
421/* Other helpful shell-like commands */
422#define CONFIG_MD5
423#define CONFIG_SHA1
424#define CONFIG_CMD_MD5SUM
425#define CONFIG_CMD_SHA1
426#define CONFIG_CMD_ASKENV
427#define CONFIG_CMD_SETEXPR
428
429
430/* -------------------------------------------------------------------- */
431
432/* Image manipulation and booting */
433
434/* We use the OpenFirmware-esque "Flattened Device Tree" */
435#define CONFIG_OF_LIBFDT
436#define CONFIG_OF_BOARD_SETUP
437#define CONFIG_OF_STDOUT_VIA_ALIAS
438
439/*
440 * For booting Linux, the board info and command line data
441 * have to be in the first 64 MB of memory, since this is
442 * the maximum mapped by the Linux kernel during initialization.
443 */
444#define CONFIG_CMD_ELF
445#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Maximum kernel memory map */
446#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Maximum kernel size of 64MB */
447
448/* This is the default address for commands with an optional address arg */
449#define CONFIG_LOADADDR 100000
450#define CONFIG_SYS_LOAD_ADDR 0x100000
451
452/* Test memory starting from the default load address to just below 2GB */
453#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_LOAD_ADDR
454#define CONFIG_SYS_MEMTEST_END 0x7f000000
455
456#define CONFIG_BOOTDELAY 20
457#define CONFIG_BOOTCOMMAND "echo Not yet flashed"
458#define CONFIG_BOOTARGS ""
459#define CONFIG_BOOTARGS_DYNAMIC "console=ttyS0,${baudrate}n1"
460
461/* Extra environment parameters */
462#define CONFIG_EXTRA_ENV_SETTINGS \
Kyle Moffett7985f7e2011-12-15 22:26:53 -0500463 "ethprime=e1000#0\0" \
464 "ethrotate=no\0" \
465 "setbootargs=setenv bootargs " \
466 "\"${bootargs} "CONFIG_BOOTARGS_DYNAMIC"\"\0" \
Kyle Moffettf8bbb4d2011-12-07 16:39:16 -0500467 "perf_mode=performance\0" \
468 "hwconfig=" "fsl_ddr:ctlr_intlv=bank,bank_intlv=cs0_cs1;" \
469 "usb1:dr_mode=host,phy_type=ulpi\0" \
Kyle Moffett7985f7e2011-12-15 22:26:53 -0500470 "flkernel=0xe8000000\0" \
Kyle Moffettf8bbb4d2011-12-07 16:39:16 -0500471 "flinitramfs=0xe8800000\0" \
472 "fldevicetree=0xeff20000\0" \
473 "flbootm=bootm ${flkernel} ${flinitramfs} ${fldevicetree}\0" \
Kyle Moffett0ecb5512011-12-15 22:26:52 -0500474 "flboot=run preboot; run flbootm\0" \
475 "restore_eeprom=i2c dev 0 && " \
476 "eeprom read $loadaddr 0x0000 0x2000 && " \
477 "env import -c $loadaddr 0x2000\0"
Kyle Moffettf8bbb4d2011-12-07 16:39:16 -0500478
479#endif /* __CONFIG_H */