| Tom Rini | 53633a8 | 2024-02-29 12:33:36 -0500 | [diff] [blame] | 1 | NXP LPC1850 Reset Generation Unit (RGU) |
| 2 | ======================================== |
| 3 | |
| 4 | Please also refer to reset.txt in this directory for common reset |
| 5 | controller binding usage. |
| 6 | |
| 7 | Required properties: |
| 8 | - compatible: Should be "nxp,lpc1850-rgu" |
| 9 | - reg: register base and length |
| 10 | - clocks: phandle and clock specifier to RGU clocks |
| 11 | - clock-names: should contain "delay" and "reg" |
| 12 | - #reset-cells: should be 1 |
| 13 | |
| 14 | See table below for valid peripheral reset numbers. Numbers not |
| 15 | in the table below are either reserved or not applicable for |
| 16 | normal operation. |
| 17 | |
| 18 | Reset Peripheral |
| 19 | 9 System control unit (SCU) |
| 20 | 12 ARM Cortex-M0 subsystem core (LPC43xx only) |
| 21 | 13 CPU core |
| 22 | 16 LCD controller |
| 23 | 17 USB0 |
| 24 | 18 USB1 |
| 25 | 19 DMA |
| 26 | 20 SDIO |
| 27 | 21 External memory controller (EMC) |
| 28 | 22 Ethernet |
| 29 | 25 Flash bank A |
| 30 | 27 EEPROM |
| 31 | 28 GPIO |
| 32 | 29 Flash bank B |
| 33 | 32 Timer0 |
| 34 | 33 Timer1 |
| 35 | 34 Timer2 |
| 36 | 35 Timer3 |
| 37 | 36 Repetitive Interrupt timer (RIT) |
| 38 | 37 State Configurable Timer (SCT) |
| 39 | 38 Motor control PWM (MCPWM) |
| 40 | 39 QEI |
| 41 | 40 ADC0 |
| 42 | 41 ADC1 |
| 43 | 42 DAC |
| 44 | 44 USART0 |
| 45 | 45 UART1 |
| 46 | 46 USART2 |
| 47 | 47 USART3 |
| 48 | 48 I2C0 |
| 49 | 49 I2C1 |
| 50 | 50 SSP0 |
| 51 | 51 SSP1 |
| 52 | 52 I2S0 and I2S1 |
| 53 | 53 Serial Flash Interface (SPIFI) |
| 54 | 54 C_CAN1 |
| 55 | 55 C_CAN0 |
| 56 | 56 ARM Cortex-M0 application core (LPC4370 only) |
| 57 | 57 SGPIO (LPC43xx only) |
| 58 | 58 SPI (LPC43xx only) |
| 59 | 60 ADCHS (12-bit ADC) (LPC4370 only) |
| 60 | |
| 61 | Refer to NXP LPC18xx or LPC43xx user manual for more details about |
| 62 | the reset signals and the connected block/peripheral. |
| 63 | |
| 64 | Reset provider example: |
| 65 | rgu: reset-controller@40053000 { |
| 66 | compatible = "nxp,lpc1850-rgu"; |
| 67 | reg = <0x40053000 0x1000>; |
| 68 | clocks = <&cgu BASE_SAFE_CLK>, <&ccu1 CLK_CPU_BUS>; |
| 69 | clock-names = "delay", "reg"; |
| 70 | #reset-cells = <1>; |
| 71 | }; |
| 72 | |
| 73 | Reset consumer example: |
| 74 | mac: ethernet@40010000 { |
| 75 | compatible = "nxp,lpc1850-dwmac", "snps,dwmac-3.611", "snps,dwmac"; |
| 76 | reg = <0x40010000 0x2000>; |
| 77 | interrupts = <5>; |
| 78 | interrupt-names = "macirq"; |
| 79 | clocks = <&ccu1 CLK_CPU_ETHERNET>; |
| 80 | clock-names = "stmmaceth"; |
| 81 | resets = <&rgu 22>; |
| 82 | reset-names = "stmmaceth"; |
| 83 | }; |