blob: 911203d85c17aad983ab51421cab3ba01b8ab7e7 [file] [log] [blame]
Xie Xiaobo49f5bef2013-06-24 15:01:30 +08001/*
2 * Copyright 2013 Freescale Semiconductor, Inc.
3 *
York Sun3aab0cd2013-08-12 14:57:12 -07004 * SPDX-License-Identifier: GPL-2.0+
Xie Xiaobo49f5bef2013-06-24 15:01:30 +08005 */
6
7/*
8 * QorIQ P1 Tower boards configuration file
9 */
10#ifndef __CONFIG_H
11#define __CONFIG_H
12
13#if defined(CONFIG_TWR_P1025)
14#define CONFIG_BOARDNAME "TWR-P1025"
15#define CONFIG_P1025
16#define CONFIG_PHY_ATHEROS
17#define CONFIG_QE
18#define CONFIG_SYS_LBC_LBCR 0x00080000 /* Conversion of LBC addr */
19#define CONFIG_SYS_LBC_LCRR 0x80000002 /* LB clock ratio reg */
20#endif
21
22#ifdef CONFIG_SDCARD
23#define CONFIG_RAMBOOT_SDCARD
24#define CONFIG_SYS_RAMBOOT
25#define CONFIG_SYS_EXTRA_ENV_RELOC
26#define CONFIG_SYS_TEXT_BASE 0x11000000
Prabhakar Kushwahae222b1f2014-01-14 11:34:26 +053027#define CONFIG_RESET_VECTOR_ADDRESS 0x110bfffc
Xie Xiaobo49f5bef2013-06-24 15:01:30 +080028#endif
29
30#ifndef CONFIG_SYS_TEXT_BASE
Prabhakar Kushwahae222b1f2014-01-14 11:34:26 +053031#define CONFIG_SYS_TEXT_BASE 0xeff40000
Xie Xiaobo49f5bef2013-06-24 15:01:30 +080032#endif
33
34#ifndef CONFIG_RESET_VECTOR_ADDRESS
35#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
36#endif
37
38#ifndef CONFIG_SYS_MONITOR_BASE
39#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
40#endif
41
42/* High Level Configuration Options */
43#define CONFIG_BOOKE
44#define CONFIG_E500
Xie Xiaobo49f5bef2013-06-24 15:01:30 +080045
46#define CONFIG_MP
47
48#define CONFIG_FSL_ELBC
49#define CONFIG_PCI
50#define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */
51#define CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */
52#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
53#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
54#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
55#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
56
57#define CONFIG_FSL_LAW
58#define CONFIG_TSEC_ENET /* tsec ethernet support */
59#define CONFIG_ENV_OVERWRITE
60
61#define CONFIG_CMD_SATA
62#define CONFIG_SATA_SIL3114
63#define CONFIG_SYS_SATA_MAX_DEVICE 2
64#define CONFIG_LIBATA
65#define CONFIG_LBA48
66
67#ifndef __ASSEMBLY__
68extern unsigned long get_board_sys_clk(unsigned long dummy);
69#endif
70#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /*sysclk for TWR-P1025 */
71
72#define CONFIG_DDR_CLK_FREQ 66666666
73
74#define CONFIG_HWCONFIG
75/*
76 * These can be toggled for performance analysis, otherwise use default.
77 */
78#define CONFIG_L2_CACHE
79#define CONFIG_BTB
80
81#define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */
82
83#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
84#define CONFIG_SYS_MEMTEST_END 0x1fffffff
85#define CONFIG_PANIC_HANG /* do not reset board on panic */
86
87#define CONFIG_SYS_CCSRBAR 0xffe00000
88#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
89
90/* DDR Setup */
York Sun5614e712013-09-30 09:22:09 -070091#define CONFIG_SYS_FSL_DDR3
Xie Xiaobo49f5bef2013-06-24 15:01:30 +080092
93#define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_512M
94#define CONFIG_CHIP_SELECTS_PER_CTRL 1
95
96#define CONFIG_SYS_SDRAM_SIZE (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19))
97#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
98#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
99
100#define CONFIG_NUM_DDR_CONTROLLERS 1
101#define CONFIG_DIMM_SLOTS_PER_CTLR 1
102
103/* Default settings for DDR3 */
104#define CONFIG_SYS_DDR_CS0_BNDS 0x0000001f
105#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202
106#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000
107#define CONFIG_SYS_DDR_CS1_BNDS 0x00000000
108#define CONFIG_SYS_DDR_CS1_CONFIG 0x00000000
109#define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000
110
111#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
112#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000
113#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000
114#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000
115
116#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600
117#define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8655a608
118#define CONFIG_SYS_DDR_SR_CNTR 0x00000000
119#define CONFIG_SYS_DDR_RCW_1 0x00000000
120#define CONFIG_SYS_DDR_RCW_2 0x00000000
121#define CONFIG_SYS_DDR_CONTROL 0xc70c0000 /* Type = DDR3 */
122#define CONFIG_SYS_DDR_CONTROL_2 0x04401050
123#define CONFIG_SYS_DDR_TIMING_4 0x00220001
124#define CONFIG_SYS_DDR_TIMING_5 0x03402400
125
126#define CONFIG_SYS_DDR_TIMING_3 0x00020000
127#define CONFIG_SYS_DDR_TIMING_0 0x00220004
128#define CONFIG_SYS_DDR_TIMING_1 0x5c5b6544
129#define CONFIG_SYS_DDR_TIMING_2 0x0fa880de
130#define CONFIG_SYS_DDR_CLK_CTRL 0x03000000
131#define CONFIG_SYS_DDR_MODE_1 0x80461320
132#define CONFIG_SYS_DDR_MODE_2 0x00008000
133#define CONFIG_SYS_DDR_INTERVAL 0x09480000
134
135/*
136 * Memory map
137 *
138 * 0x0000_0000 0x1fff_ffff DDR Up to 512MB cacheable
139 * 0x8000_0000 0xdfff_ffff PCI Express Mem 1.5G non-cacheable(PCIe * 3)
140 * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable
141 *
142 * Localbus
143 * 0xe000_0000 0xe002_0000 SSD1289 128K non-cacheable
144 * 0xec00_0000 0xefff_ffff FLASH Up to 64M non-cacheable
145 *
146 * 0xff90_0000 0xff97_ffff L2 SRAM Up to 512K cacheable
147 * 0xffd0_0000 0xffd0_3fff init ram 16K Cacheable
148 * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
149 */
150
151/*
152 * Local Bus Definitions
153 */
154#define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */
155#define CONFIG_SYS_FLASH_BASE 0xec000000
156
157#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
158
159#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS)) \
160 | BR_PS_16 | BR_V)
161
162#define CONFIG_FLASH_OR_PRELIM 0xfc0000b1
163
164#define CONFIG_SYS_SSD_BASE 0xe0000000
165#define CONFIG_SYS_SSD_BASE_PHYS CONFIG_SYS_SSD_BASE
166#define CONFIG_SSD_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_SSD_BASE_PHYS) | \
167 BR_PS_16 | BR_V)
168#define CONFIG_SSD_OR_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
169 OR_GPCM_ACS_DIV2 | OR_GPCM_SCY | \
170 OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
171
172#define CONFIG_SYS_BR2_PRELIM CONFIG_SSD_BR_PRELIM
173#define CONFIG_SYS_OR2_PRELIM CONFIG_SSD_OR_PRELIM
174
175#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
176#define CONFIG_SYS_FLASH_QUIET_TEST
177#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
178
179#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
180
181#undef CONFIG_SYS_FLASH_CHECKSUM
182#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
183#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
184
185#define CONFIG_FLASH_CFI_DRIVER
186#define CONFIG_SYS_FLASH_CFI
187#define CONFIG_SYS_FLASH_EMPTY_INFO
188#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
189
190#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
191
192#define CONFIG_SYS_INIT_RAM_LOCK
193#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000
194/* Initial L1 address */
195#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR
196#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
197#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
198/* Size of used area in RAM */
199#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
200
201#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
202 GENERATED_GBL_DATA_SIZE)
203#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
204
Prabhakar Kushwaha9307cba2014-03-31 15:31:48 +0530205#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
Xie Xiaobo49f5bef2013-06-24 15:01:30 +0800206#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)/* Reserved for malloc */
207
208#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
209#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
210
211/* Serial Port
212 * open - index 2
213 * shorted - index 1
214 */
215#define CONFIG_CONS_INDEX 1
216#undef CONFIG_SERIAL_SOFTWARE_FIFO
217#define CONFIG_SYS_NS16550
218#define CONFIG_SYS_NS16550_SERIAL
219#define CONFIG_SYS_NS16550_REG_SIZE 1
220#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
221
222#define CONFIG_SYS_BAUDRATE_TABLE \
223 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
224
225#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
226#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
227
228/* Use the HUSH parser */
229#define CONFIG_SYS_HUSH_PARSER
230#ifdef CONFIG_SYS_HUSH_PARSER
231#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
232#endif
233
234/*
235 * Pass open firmware flat tree
236 */
237#define CONFIG_OF_LIBFDT
238#define CONFIG_OF_BOARD_SETUP
239#define CONFIG_OF_STDOUT_VIA_ALIAS
240
Xie Xiaobo49f5bef2013-06-24 15:01:30 +0800241/* new uImage format support */
242#define CONFIG_FIT
243#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
244
245/* I2C */
246#define CONFIG_SYS_I2C
247#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */
248#define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C spd and slave address */
249#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
250#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
251#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
252
253/*
254 * I2C2 EEPROM
255 */
256#define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C spd and slave address */
257#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
258#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
259
260#define CONFIG_SYS_I2C_PCA9555_ADDR 0x23
261
262/* enable read and write access to EEPROM */
263#define CONFIG_CMD_EEPROM
264#define CONFIG_SYS_I2C_MULTI_EEPROMS
265#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
266#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
267#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
268
269/*
270 * eSPI - Enhanced SPI
271 */
272#define CONFIG_HARD_SPI
273#define CONFIG_FSL_ESPI
274
275#if defined(CONFIG_PCI)
276/*
277 * General PCI
278 * Memory space is mapped 1-1, but I/O space must start from 0.
279 */
280
281/* controller 2, direct to uli, tgtid 2, Base address 9000 */
282#define CONFIG_SYS_PCIE2_NAME "TWR-ELEV PCIe SLOT"
283#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
284#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
285#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
286#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
287#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
288#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
289#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
290#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
291
292/* controller 1, tgtid 1, Base address a000 */
293#define CONFIG_SYS_PCIE1_NAME "mini PCIe SLOT"
294#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
295#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
296#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000
297#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
298#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000
299#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
300#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000
301#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
302
303#define CONFIG_NET_MULTI
304#define CONFIG_PCI_PNP /* do pci plug-and-play */
305#define CONFIG_E1000 /* Defind e1000 pci Ethernet card*/
306#define CONFIG_CMD_PCI
307#define CONFIG_CMD_NET
308
309#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
310#define CONFIG_DOS_PARTITION
311#endif /* CONFIG_PCI */
312
313#if defined(CONFIG_TSEC_ENET)
314
315#ifndef CONFIG_NET_MULTI
316#define CONFIG_NET_MULTI
317#endif
318
319#define CONFIG_MII /* MII PHY management */
320#define CONFIG_TSEC1
321#define CONFIG_TSEC1_NAME "eTSEC1"
322#undef CONFIG_TSEC2
323#undef CONFIG_TSEC2_NAME
324#define CONFIG_TSEC3
325#define CONFIG_TSEC3_NAME "eTSEC3"
326
327#define TSEC1_PHY_ADDR 2
328#define TSEC2_PHY_ADDR 0
329#define TSEC3_PHY_ADDR 1
330
331#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
332#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
333#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
334
335#define TSEC1_PHYIDX 0
336#define TSEC2_PHYIDX 0
337#define TSEC3_PHYIDX 0
338
339#define CONFIG_ETHPRIME "eTSEC1"
340
341#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
342
343#define CONFIG_HAS_ETH0
344#define CONFIG_HAS_ETH1
345#undef CONFIG_HAS_ETH2
346#endif /* CONFIG_TSEC_ENET */
347
348#ifdef CONFIG_QE
349/* QE microcode/firmware address */
350#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
Zhao Qiangdcf1d772014-03-21 16:21:44 +0800351#define CONFIG_SYS_QE_FW_ADDR 0xefec0000
Xie Xiaobo49f5bef2013-06-24 15:01:30 +0800352#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
353#endif /* CONFIG_QE */
354
355#ifdef CONFIG_TWR_P1025
356/*
357 * QE UEC ethernet configuration
358 */
359#define CONFIG_MIIM_ADDRESS (CONFIG_SYS_CCSRBAR + 0x82120)
360
361#undef CONFIG_UEC_ETH
362#define CONFIG_PHY_MODE_NEED_CHANGE
363
364#define CONFIG_UEC_ETH1 /* ETH1 */
365#define CONFIG_HAS_ETH0
366
367#ifdef CONFIG_UEC_ETH1
368#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */
369#define CONFIG_SYS_UEC1_RX_CLK QE_CLK12 /* CLK12 for MII */
370#define CONFIG_SYS_UEC1_TX_CLK QE_CLK9 /* CLK9 for MII */
371#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
372#define CONFIG_SYS_UEC1_PHY_ADDR 0x18 /* 0x18 for MII */
373#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII
374#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
375#endif /* CONFIG_UEC_ETH1 */
376
377#define CONFIG_UEC_ETH5 /* ETH5 */
378#define CONFIG_HAS_ETH1
379
380#ifdef CONFIG_UEC_ETH5
381#define CONFIG_SYS_UEC5_UCC_NUM 4 /* UCC5 */
382#define CONFIG_SYS_UEC5_RX_CLK QE_CLK_NONE
383#define CONFIG_SYS_UEC5_TX_CLK QE_CLK13 /* CLK 13 for RMII */
384#define CONFIG_SYS_UEC5_ETH_TYPE FAST_ETH
385#define CONFIG_SYS_UEC5_PHY_ADDR 0x19 /* 0x19 for RMII */
386#define CONFIG_SYS_UEC5_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
387#define CONFIG_SYS_UEC5_INTERFACE_SPEED 100
388#endif /* CONFIG_UEC_ETH5 */
389#endif /* CONFIG_TWR-P1025 */
390
391/*
392 * Environment
393 */
394#ifdef CONFIG_SYS_RAMBOOT
395#ifdef CONFIG_RAMBOOT_SDCARD
396#define CONFIG_ENV_IS_IN_MMC
397#define CONFIG_ENV_SIZE 0x2000
398#define CONFIG_SYS_MMC_ENV_DEV 0
399#else
400#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
401#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
402#define CONFIG_ENV_SIZE 0x2000
403#endif
404#else
405#define CONFIG_ENV_IS_IN_FLASH
Xie Xiaobo49f5bef2013-06-24 15:01:30 +0800406#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
Xie Xiaobo49f5bef2013-06-24 15:01:30 +0800407#define CONFIG_ENV_SIZE 0x2000
408#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
409#endif
410
411#define CONFIG_LOADS_ECHO /* echo on for serial download */
412#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
413
414/*
415 * Command line configuration.
416 */
417#include <config_cmd_default.h>
418
419#define CONFIG_CMD_IRQ
420#define CONFIG_CMD_PING
421#define CONFIG_CMD_I2C
422#define CONFIG_CMD_MII
423#define CONFIG_CMD_ELF
424#define CONFIG_CMD_SETEXPR
425#define CONFIG_CMD_REGINFO
426
427/*
428 * USB
429 */
430#define CONFIG_HAS_FSL_DR_USB
431
432#if defined(CONFIG_HAS_FSL_DR_USB)
433#define CONFIG_USB_EHCI
434
435#ifdef CONFIG_USB_EHCI
436#define CONFIG_CMD_USB
437#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
438#define CONFIG_USB_EHCI_FSL
439#define CONFIG_USB_STORAGE
440#endif
441#endif
442
443#define CONFIG_MMC
444
445#ifdef CONFIG_MMC
446#define CONFIG_FSL_ESDHC
447#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
448#define CONFIG_CMD_MMC
449#define CONFIG_GENERIC_MMC
450#endif
451
452#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) \
453 || defined(CONFIG_FSL_SATA)
454#define CONFIG_CMD_EXT2
455#define CONFIG_CMD_FAT
456#define CONFIG_DOS_PARTITION
457#endif
458
459#undef CONFIG_WATCHDOG /* watchdog disabled */
460
461/*
462 * Miscellaneous configurable options
463 */
464#define CONFIG_SYS_LONGHELP /* undef to save memory */
465#define CONFIG_CMDLINE_EDITING /* Command-line editing */
466#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
Xie Xiaobo49f5bef2013-06-24 15:01:30 +0800467#if defined(CONFIG_CMD_KGDB)
468#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
469#else
470#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
471#endif
472#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
473 /* Print Buffer Size */
474#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
475#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
Xie Xiaobo49f5bef2013-06-24 15:01:30 +0800476
477/*
478 * For booting Linux, the board info and command line data
479 * have to be in the first 64 MB of memory, since this is
480 * the maximum mapped by the Linux kernel during initialization.
481 */
482#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux*/
483#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
484
485/*
486 * Environment Configuration
487 */
488#define CONFIG_HOSTNAME unknown
489#define CONFIG_ROOTPATH "/opt/nfsroot"
490#define CONFIG_BOOTFILE "uImage"
491#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
492
493/* default location for tftp and bootm */
494#define CONFIG_LOADADDR 1000000
495
496#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
497#define CONFIG_BOOTARGS /* the boot command will set bootargs */
498
499#define CONFIG_BAUDRATE 115200
500
501#define CONFIG_EXTRA_ENV_SETTINGS \
502"netdev=eth0\0" \
503"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
504"loadaddr=1000000\0" \
505"bootfile=uImage\0" \
506"dtbfile=twr-p1025twr.dtb\0" \
507"ramdiskfile=rootfs.ext2.gz.uboot\0" \
508"qefirmwarefile=fsl_qe_ucode_1021_10_A.bin\0" \
509"tftpflash=tftpboot $loadaddr $uboot; " \
510 "protect off " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
511 "erase " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
512 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize; " \
513 "protect on " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
514 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize\0" \
515"kernelflash=tftpboot $loadaddr $bootfile; " \
516 "protect off 0xefa80000 +$filesize; " \
517 "erase 0xefa80000 +$filesize; " \
518 "cp.b $loadaddr 0xefa80000 $filesize; " \
519 "protect on 0xefa80000 +$filesize; " \
520 "cmp.b $loadaddr 0xefa80000 $filesize\0" \
521"dtbflash=tftpboot $loadaddr $dtbfile; " \
522 "protect off 0xefe80000 +$filesize; " \
523 "erase 0xefe80000 +$filesize; " \
524 "cp.b $loadaddr 0xefe80000 $filesize; " \
525 "protect on 0xefe80000 +$filesize; " \
526 "cmp.b $loadaddr 0xefe80000 $filesize\0" \
527"ramdiskflash=tftpboot $loadaddr $ramdiskfile; " \
528 "protect off 0xeeb80000 +$filesize; " \
529 "erase 0xeeb80000 +$filesize; " \
530 "cp.b $loadaddr 0xeeb80000 $filesize; " \
531 "protect on 0xeeb80000 +$filesize; " \
532 "cmp.b $loadaddr 0xeeb80000 $filesize\0" \
533"qefirmwareflash=tftpboot $loadaddr $qefirmwarefile; " \
534 "protect off 0xefec0000 +$filesize; " \
535 "erase 0xefec0000 +$filesize; " \
536 "cp.b $loadaddr 0xefec0000 $filesize; " \
537 "protect on 0xefec0000 +$filesize; " \
538 "cmp.b $loadaddr 0xefec0000 $filesize\0" \
539"consoledev=ttyS0\0" \
540"ramdiskaddr=2000000\0" \
541"ramdiskfile=rootfs.ext2.gz.uboot\0" \
542"fdtaddr=c00000\0" \
543"bdev=sda1\0" \
544"norbootaddr=ef080000\0" \
545"norfdtaddr=ef040000\0" \
546"ramdisk_size=120000\0" \
547"usbboot=setenv bootargs root=/dev/sda1 rw rootdelay=5 " \
548"console=$consoledev,$baudrate $othbootargs ; bootm 0xefa80000 - 0xefe80000"
549
550#define CONFIG_NFSBOOTCOMMAND \
551"setenv bootargs root=/dev/nfs rw " \
552"nfsroot=$serverip:$rootpath " \
553"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
554"console=$consoledev,$baudrate $othbootargs;" \
555"tftp $loadaddr $bootfile&&" \
556"tftp $fdtaddr $fdtfile&&" \
557"bootm $loadaddr - $fdtaddr"
558
559#define CONFIG_HDBOOT \
560"setenv bootargs root=/dev/$bdev rw rootdelay=30 " \
561"console=$consoledev,$baudrate $othbootargs;" \
562"usb start;" \
563"ext2load usb 0:1 $loadaddr /boot/$bootfile;" \
564"ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \
565"bootm $loadaddr - $fdtaddr"
566
567#define CONFIG_USB_FAT_BOOT \
568"setenv bootargs root=/dev/ram rw " \
569"console=$consoledev,$baudrate $othbootargs " \
570"ramdisk_size=$ramdisk_size;" \
571"usb start;" \
572"fatload usb 0:2 $loadaddr $bootfile;" \
573"fatload usb 0:2 $fdtaddr $fdtfile;" \
574"fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \
575"bootm $loadaddr $ramdiskaddr $fdtaddr"
576
577#define CONFIG_USB_EXT2_BOOT \
578"setenv bootargs root=/dev/ram rw " \
579"console=$consoledev,$baudrate $othbootargs " \
580"ramdisk_size=$ramdisk_size;" \
581"usb start;" \
582"ext2load usb 0:4 $loadaddr $bootfile;" \
583"ext2load usb 0:4 $fdtaddr $fdtfile;" \
584"ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
585"bootm $loadaddr $ramdiskaddr $fdtaddr"
586
587#define CONFIG_NORBOOT \
588"setenv bootargs root=/dev/mtdblock3 rw " \
589"console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \
590"bootm $norbootaddr - $norfdtaddr"
591
592#define CONFIG_RAMBOOTCOMMAND_TFTP \
593"setenv bootargs root=/dev/ram rw " \
594"console=$consoledev,$baudrate $othbootargs " \
595"ramdisk_size=$ramdisk_size;" \
596"tftp $ramdiskaddr $ramdiskfile;" \
597"tftp $loadaddr $bootfile;" \
598"tftp $fdtaddr $fdtfile;" \
599"bootm $loadaddr $ramdiskaddr $fdtaddr"
600
601#define CONFIG_RAMBOOTCOMMAND \
602"setenv bootargs root=/dev/ram rw " \
603"console=$consoledev,$baudrate $othbootargs " \
604"ramdisk_size=$ramdisk_size;" \
605"bootm 0xefa80000 0xeeb80000 0xefe80000"
606
607#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
608
609#endif /* __CONFIG_H */