| /* |
| * (C) Copyright 2003-2005 |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. |
| * |
| * (C) Copyright 2006 |
| * Eric Schumann, Phytec Messatechnik GmbH |
| * |
| * (C) Copyright 2009 |
| * Jon Smirl <jonsmirl@gmail.com> |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #define CONFIG_BOARDINFO "phyCORE-MPC5200B-tiny" |
| |
| /*----------------------------------------------------------------------------- |
| High Level Configuration Options |
| (easy to change) |
| -----------------------------------------------------------------------------*/ |
| #define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ |
| #define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */ |
| #define CONFIG_MPC5200_DDR 1 /* (with DDR-SDRAM) */ |
| #define CONFIG_PHYCORE_MPC5200B_TINY 1 /* phyCORE-MPC5200B -> */ |
| /* FEC configuration and IDE */ |
| |
| /* |
| * Valid values for CONFIG_SYS_TEXT_BASE are: |
| * 0xFFF00000 boot high (standard configuration) |
| * 0xFF000000 boot low |
| * 0x00100000 boot from RAM (for testing only) |
| */ |
| #ifndef CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_TEXT_BASE 0xFFF00000 |
| #endif |
| |
| #define CONFIG_SYS_MPC5XXX_CLKIN 33333333 /* ... running at 33.333333MHz */ |
| #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ |
| #define BOOTFLAG_WARM 0x02 /* Software reboot */ |
| |
| /*----------------------------------------------------------------------------- |
| Serial console configuration |
| -----------------------------------------------------------------------------*/ |
| #define CONFIG_PSC_CONSOLE 3 /* console is on PSC3 -> */ |
| /*define gps port conf. */ |
| /* register later on to */ |
| /*enable UART function! */ |
| #define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ |
| #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_EEPROM |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_JFFS2 |
| #define CONFIG_CMD_MII |
| #define CONFIG_CMD_NFS |
| #define CONFIG_CMD_PCI |
| |
| #define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */ |
| |
| #if (CONFIG_SYS_TEXT_BASE == 0xFF000000) /* Boot low */ |
| #define CONFIG_SYS_LOWBOOT 1 |
| #endif |
| /* RAMBOOT will be defined automatically in memory section */ |
| |
| #define CONFIG_JFFS2_CMDLINE |
| #define MTDIDS_DEFAULT "nor0=physmap-flash.0" |
| #define MTDPARTS_DEFAULT "mtdparts=physmap-flash.0:256k(ubootl)," \ |
| "1792k(kernel),13312k(jffs2),256k(uboot)ro,256k(oftree),-(space)" |
| |
| /*----------------------------------------------------------------------------- |
| Autobooting |
| -----------------------------------------------------------------------------*/ |
| #define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ |
| #define CONFIG_ZERO_BOOTDELAY_CHECK /* allow stopping of boot process */ |
| /* even with bootdelay=0 */ |
| #undef CONFIG_BOOTARGS |
| |
| |
| #define CONFIG_PREBOOT "echo;" \ |
| "echo Type \"run bootcmd_net\" to load Kernel over TFTP and to "\ |
| "mount root filesystem over NFS;" \ |
| "echo" |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "netdev=eth0\0" \ |
| "uimage=uImage-pcm030\0" \ |
| "oftree=oftree-pcm030.dtb\0" \ |
| "jffs2=root-pcm030.jffs2\0" \ |
| "uboot=u-boot-pcm030.bin\0" \ |
| "bargs_base=setenv bootargs console=ttyPSC0,$(baudrate)" \ |
| " $(mtdparts) rw\0" \ |
| "bargs_flash=setenv bootargs $(bootargs) root=/dev/mtdblock2" \ |
| " rootfstype=jffs2\0" \ |
| "bargs_nfs=setenv bootargs $(bootargs) root=/dev/nfs" \ |
| " ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)::" \ |
| "$(netdev):off nfsroot=$(serverip):$(nfsrootfs),v3,tcp\0" \ |
| "bcmd_net=run bargs_base bargs_nfs; tftpboot 0x500000 $(uimage);" \ |
| " tftp 0x400000 $(oftree); bootm 0x500000 - 0x400000\0" \ |
| "bcmd_flash=run bargs_base bargs_flash; bootm 0xff040000 - " \ |
| "0xfff40000\0" \ |
| " cp.b 0x400000 0xff040000 $(filesize)\0" \ |
| "prg_jffs2=tftp 0x400000 $(jffs2); erase 0xff200000 0xffefffff; " \ |
| "cp.b 0x400000 0xff200000 $(filesize)\0" \ |
| "prg_oftree=tftp 0x400000 $(oftree); erase 0xfff40000 0xfff5ffff;" \ |
| " cp.b 0x400000 0xfff40000 $(filesize)\0" \ |
| "update=tftpboot 0x400000 $(uboot);erase 0xFFF00000 0xfff3ffff;" \ |
| " cp.b 0x400000 0xFFF00000 $(filesize)\0" \ |
| "unlock=yes\0" \ |
| "" |
| |
| #define CONFIG_BOOTCOMMAND "run bcmd_flash" |
| |
| /*-------------------------------------------------------------------------- |
| IPB Bus clocking configuration. |
| ---------------------------------------------------------------------------*/ |
| #define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ |
| |
| /*------------------------------------------------------------------------- |
| * PCI Mapping: |
| * 0x40000000 - 0x4fffffff - PCI Memory |
| * 0x50000000 - 0x50ffffff - PCI IO Space |
| * -----------------------------------------------------------------------*/ |
| #define CONFIG_PCI 1 |
| #define CONFIG_PCI_PNP 1 |
| #define CONFIG_PCI_SCAN_SHOW 1 |
| #define CONFIG_PCI_MEM_BUS 0x40000000 |
| #define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS |
| #define CONFIG_PCI_MEM_SIZE 0x10000000 |
| #define CONFIG_PCI_IO_BUS 0x50000000 |
| #define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS |
| #define CONFIG_PCI_IO_SIZE 0x01000000 |
| #define CONFIG_SYS_XLB_PIPELINING 1 |
| |
| /*--------------------------------------------------------------------------- |
| I2C configuration |
| ---------------------------------------------------------------------------*/ |
| #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ |
| #define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ |
| #define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ |
| #define CONFIG_SYS_I2C_SLAVE 0x7F |
| |
| /*--------------------------------------------------------------------------- |
| EEPROM CAT24WC32 configuration |
| ---------------------------------------------------------------------------*/ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010100x */ |
| #define CONFIG_SYS_I2C_FACT_ADDR 0x52 /* EEPROM CAT24WC32 */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ |
| #define CONFIG_SYS_EEPROM_SIZE 2048 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 15 |
| |
| /*--------------------------------------------------------------------------- |
| RTC configuration |
| ---------------------------------------------------------------------------*/ |
| #define RTC |
| #define CONFIG_RTC_PCF8563 1 |
| #define CONFIG_SYS_I2C_RTC_ADDR 0x51 |
| |
| /*--------------------------------------------------------------------------- |
| Flash configuration |
| ---------------------------------------------------------------------------*/ |
| |
| #define CONFIG_SYS_FLASH_BASE 0xff000000 |
| #define CONFIG_SYS_FLASH_SIZE 0x01000000 |
| #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } |
| |
| #define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ |
| #define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| #define CONFIG_SYS_MAX_FLASH_SECT 260 /* max num of sects on one chip */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ |
| /* (= chip selects) */ |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE |
| |
| /* |
| * Use also hardware protection. This seems required, as the BDI uses |
| * hardware protection. Without this, U-Boot can't work with this sectors, |
| * as its protection is software only by default |
| */ |
| #define CONFIG_SYS_FLASH_PROTECTION 1 |
| |
| /*--------------------------------------------------------------------------- |
| Environment settings |
| ---------------------------------------------------------------------------*/ |
| |
| /* pcm030 ships with environment is EEPROM by default */ |
| #define CONFIG_ENV_IS_IN_EEPROM 1 |
| #define CONFIG_ENV_OFFSET 0x00 /* environment starts at the */ |
| /*beginning of the EEPROM */ |
| #define CONFIG_ENV_SIZE CONFIG_SYS_EEPROM_SIZE |
| |
| #define CONFIG_ENV_OVERWRITE 1 |
| |
| /*----------------------------------------------------------------------------- |
| Memory map |
| -----------------------------------------------------------------------------*/ |
| #define CONFIG_SYS_MBAR 0xF0000000 /* MBAR has to be switched by other */ |
| /* bootloader or debugger config */ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_DEFAULT_MBAR 0x80000000 |
| /* Use SRAM until RAM will be available */ |
| #define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM |
| #define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used */ |
| /* area in DPRAM */ |
| #define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes */ |
| /* reserved for initial data */ |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - \ |
| CONFIG_SYS_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE |
| #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) |
| # define CONFIG_SYS_RAMBOOT 1 |
| #endif |
| |
| #define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ |
| #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /*----------------------------------------------------------------------------- |
| Ethernet configuration |
| -----------------------------------------------------------------------------*/ |
| #define CONFIG_MPC5xxx_FEC 1 |
| #define CONFIG_MPC5xxx_FEC_MII100 |
| #define CONFIG_PHY_ADDR 0x01 |
| |
| /*--------------------------------------------------------------------------- |
| GPIO configuration |
| ---------------------------------------------------------------------------*/ |
| |
| /* GPIO port configuration |
| * |
| * Pin mapping: |
| * |
| * [29:31] = 01x |
| * PSC1_0 -> AC97 SDATA out |
| * PSC1_1 -> AC97 SDTA in |
| * PSC1_2 -> AC97 SYNC out |
| * PSC1_3 -> AC97 bitclock out |
| * PSC1_4 -> AC97 reset out |
| * |
| * [25:27] = 001 |
| * PSC2_0 -> CAN 1 Tx out |
| * PSC2_1 -> CAN 1 Rx in |
| * PSC2_2 -> CAN 2 Tx out |
| * PSC2_3 -> CAN 2 Rx in |
| * PSC2_4 -> GPIO (claimed for ATA reset, active low) |
| * |
| * |
| * [20:23] = 1100 |
| * PSC3_0 -> UART Tx out |
| * PSC3_1 -> UART Rx in |
| * PSC3_2 -> UART RTS (in/out FIXME) |
| * PSC3_3 -> UART CTS (in/out FIXME) |
| * PSC3_4 -> LocalPlus Bus CS6 \ |
| * PSC3_5 -> LocalPlus Bus CS7 / --> see [4] and [5] |
| * PSC3_6 -> dedicated SPI MOSI out (master case) |
| * PSC3_7 -> dedicated SPI MISO in (master case) |
| * PSC3_8 -> dedicated SPI SS out (master case) |
| * PSC3_9 -> dedicated SPI CLK out (master case) |
| * |
| * [18:19] = 01 |
| * USB_0 -> USB OE out |
| * USB_1 -> USB Tx- out |
| * USB_2 -> USB Tx+ out |
| * USB_3 -> USB RxD (in/out FIXME) |
| * USB_4 -> USB Rx+ in |
| * USB_5 -> USB Rx- in |
| * USB_6 -> USB PortPower out |
| * USB_7 -> USB speed out |
| * USB_8 -> USB suspend (in/out FIXME) |
| * USB_9 -> USB overcurrent in |
| * |
| * [17] = 0 |
| * USB differential mode |
| * |
| * [16] = 0 |
| * PCI enabled |
| * |
| * [12:15] = 0101 |
| * ETH_0 -> ETH Txen |
| * ETH_1 -> ETH TxD0 |
| * ETH_2 -> ETH TxD1 |
| * ETH_3 -> ETH TxD2 |
| * ETH_4 -> ETH TxD3 |
| * ETH_5 -> ETH Txerr |
| * ETH_6 -> ETH MDC |
| * ETH_7 -> ETH MDIO |
| * ETH_8 -> ETH RxDv |
| * ETH_9 -> ETH RxCLK |
| * ETH_10 -> ETH Collision |
| * ETH_11 -> ETH TxD |
| * ETH_12 -> ETH RxD0 |
| * ETH_13 -> ETH RxD1 |
| * ETH_14 -> ETH RxD2 |
| * ETH_15 -> ETH RxD3 |
| * ETH_16 -> ETH Rxerr |
| * ETH_17 -> ETH CRS |
| * |
| * [9:11] = 101 |
| * PSC6_0 -> UART RxD in |
| * PSC6_1 -> UART CTS (in/out FIXME) |
| * PSC6_2 -> UART TxD out |
| * PSC6_3 -> UART RTS (in/out FIXME) |
| * |
| * [2:3/6:7] = 00/11 |
| * TMR_0 -> ATA_CS0 out |
| * TMR_1 -> ATA_CS1 out |
| * TMR_2 -> GPIO |
| * TMR_3 -> GPIO |
| * TMR_4 -> GPIO |
| * TMR_5 -> GPIO |
| * TMR_6 -> GPIO |
| * TMR_7 -> GPIO |
| * I2C_0 -> I2C 1 Clock out |
| * I2C_1 -> I2C 1 IO in/out |
| * I2C_2 -> I2C 2 Clock out |
| * I2C_3 -> I2C 2 IO in/out |
| * |
| * [4] = 1 |
| * PSC3_5 is used as CS7 |
| * |
| * [5] = 1 |
| * PSC3_4 is used as CS6 |
| * |
| * [1] = 0 |
| * gpio_wkup_7 is GPIO |
| * |
| * [0] = 0 |
| * gpio_wkup_6 is GPIO |
| * |
| */ |
| #define CONFIG_SYS_GPS_PORT_CONFIG 0x0f551c12 |
| |
| /*----------------------------------------------------------------------------- |
| Miscellaneous configurable options |
| -------------------------------------------------------------------------------*/ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_PROMPT "uboot> " /* Monitor Command Prompt */ |
| |
| #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ |
| |
| #define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ |
| #endif |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) |
| /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */ |
| #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ |
| |
| #define CONFIG_DISPLAY_BOARDINFO 1 |
| |
| /*----------------------------------------------------------------------------- |
| Various low-level settings |
| -----------------------------------------------------------------------------*/ |
| #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI |
| #define CONFIG_SYS_HID0_FINAL HID0_ICE |
| |
| /* no burst access on the LPB */ |
| #define CONFIG_SYS_CS_BURST 0x00000000 |
| /* one deadcycle for the 33MHz statemachine */ |
| #define CONFIG_SYS_CS_DEADCYCLE 0x33333331 |
| /* one additional waitstate for the 33MHz statemachine */ |
| #define CONFIG_SYS_BOOTCS_CFG 0x0001dd00 |
| #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE |
| #define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE |
| |
| #define CONFIG_SYS_RESET_ADDRESS 0xff000000 |
| |
| /*----------------------------------------------------------------------- |
| * USB stuff |
| *----------------------------------------------------------------------- |
| */ |
| #define CONFIG_USB_CLOCK 0x0001BBBB |
| #define CONFIG_USB_CONFIG 0x00001000 |
| |
| /*--------------------------------------------------------------------------- |
| IDE/ATA stuff Supports IDE harddisk |
| ----------------------------------------------------------------------------*/ |
| |
| #undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ |
| #undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ |
| #undef CONFIG_IDE_LED /* LED for ide not supported */ |
| #define CONFIG_SYS_ATA_CS_ON_TIMER01 |
| #define CONFIG_IDE_RESET 1 /* reset for ide supported */ |
| #define CONFIG_IDE_PREINIT |
| #define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ |
| #define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */ |
| #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 |
| #define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA |
| /* Offset for data I/O */ |
| #define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) |
| /* Offset for normal register accesses */ |
| #define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) |
| /* Offset for alternate registers */ |
| #define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) |
| /* Interval between registers */ |
| #define CONFIG_SYS_ATA_STRIDE 4 |
| #define CONFIG_ATAPI 1 |
| |
| /* we enable IDE and FAT support, so we also need partition support */ |
| #define CONFIG_DOS_PARTITION 1 |
| |
| /* USB */ |
| #define CONFIG_USB_OHCI |
| #define CONFIG_USB_STORAGE |
| |
| /* pass open firmware flat tree */ |
| #define CONFIG_OF_LIBFDT 1 |
| #define CONFIG_OF_BOARD_SETUP 1 |
| |
| #define OF_CPU "PowerPC,5200@0" |
| #define OF_TBCLK CONFIG_SYS_MPC5XXX_CLKIN |
| #define OF_SOC "soc5200@f0000000" |
| #define OF_STDOUT_PATH "/soc5200@f0000000/serial@2400" |
| |
| #endif /* __CONFIG_H */ |