blob: 44c1952b51e710001d1b004d3aaf6c5f1ee5bcc8 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Configuation settings for the SAMA5D3xEK board.
*
* Copyright (C) 2012 - 2013 Atmel
*
* based on at91sam9m10g45ek.h by:
* Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include "at91-sama5_common.h"
/*
* This needs to be defined for the OHCI code to work but it is defined as
* ATMEL_ID_UHPHS in the CPU specific header files.
*/
#define ATMEL_ID_UHP 32
/*
* Specify the clock enable bit in the PMC_SCER register.
*/
#define ATMEL_PMC_UHP (1 << 6)
/* board specific (not enough SRAM) */
#define CONFIG_SAMA5D3_LCD_BASE 0x23E00000
/* NOR flash */
#ifdef CONFIG_MTD_NOR_FLASH
#define CONFIG_SYS_FLASH_BASE 0x10000000
#define CONFIG_SYS_MAX_FLASH_SECT 131
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#endif
/* SDRAM */
#define CONFIG_SYS_SDRAM_BASE 0x20000000
#define CONFIG_SYS_SDRAM_SIZE 0x20000000
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_INIT_SP_ADDR 0x318000
#else
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
#endif
/* SerialFlash */
/* NAND flash */
#ifdef CONFIG_CMD_NAND
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE 0x60000000
/* our ALE is AD21 */
#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
/* our CLE is AD22 */
#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
#define CONFIG_SYS_NAND_ONFI_DETECTION
#endif
/* USB */
#ifdef CONFIG_CMD_USB
#define CONFIG_USB_ATMEL_CLK_SEL_UPLL
#define CONFIG_USB_OHCI_NEW
#define CONFIG_SYS_USB_OHCI_CPU_INIT
#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_BASE_OHCI
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "sama5d3"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 3
#endif
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
/* SPL */
#define CONFIG_SPL_MAX_SIZE 0x18000
#define CONFIG_SPL_BSS_START_ADDR 0x20000000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
#define CONFIG_SYS_SPL_MALLOC_START 0x20080000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
#define CONFIG_SYS_MONITOR_LEN (512 << 10)
#ifdef CONFIG_SD_BOOT
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
#endif
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_SIZE 0x800
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_OOBSIZE 64
#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0
#endif