blob: 91d8091d258998d8bfa5b73a951ac6154f987ca8 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Maintainer : Steve Sakoman <steve@sakoman.com>
*
* Derived from Beagle Board, 3430 SDP, and OMAP3EVM code by
* Richard Woodruff <r-woodruff2@ti.com>
* Syed Mohammed Khasim <khasim@ti.com>
* Sunil Kumar <sunilsaini05@gmail.com>
* Shashi Ranjan <shashiranjanmca05@gmail.com>
*
* (C) Copyright 2004-2008
* Texas Instruments, <www.ti.com>
*/
#include <common.h>
#include <asm/io.h>
#include <asm/arch/mem.h>
#include <asm/arch/sys_proto.h>
#include "overo.h"
/*
* Routine: get_board_mem_timings
* Description: If we use SPL then there is no x-loader nor config header
* so we have to setup the DDR timings ourself on both banks.
*/
void get_board_mem_timings(struct board_sdrc_timings *timings)
{
timings->mr = MICRON_V_MR_165;
switch (get_board_revision()) {
case REVISION_0: /* Micron 1286MB/256MB, 1/2 banks of 128MB */
timings->mcfg = MICRON_V_MCFG_165(256 << 20);
timings->ctrla = MICRON_V_ACTIMA_165;
timings->ctrlb = MICRON_V_ACTIMB_165;
timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
break;
case REVISION_1: /* Micron 256MB/512MB, 1/2 banks of 256MB */
case REVISION_4:
timings->mcfg = MICRON_V_MCFG_200(256 << 20);
timings->ctrla = MICRON_V_ACTIMA_200;
timings->ctrlb = MICRON_V_ACTIMB_200;
timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
break;
case REVISION_2: /* Hynix 256MB/512MB, 1/2 banks of 256MB */
timings->mcfg = HYNIX_V_MCFG_200(256 << 20);
timings->ctrla = HYNIX_V_ACTIMA_200;
timings->ctrlb = HYNIX_V_ACTIMB_200;
timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
break;
case REVISION_3: /* Micron 512MB/1024MB, 1/2 banks of 512MB */
timings->mcfg = MCFG(512 << 20, 15);
timings->ctrla = MICRON_V_ACTIMA_200;
timings->ctrlb = MICRON_V_ACTIMB_200;
timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
break;
default:
timings->mcfg = MICRON_V_MCFG_165(128 << 20);
timings->ctrla = MICRON_V_ACTIMA_165;
timings->ctrlb = MICRON_V_ACTIMB_165;
timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
}
}