| menu "NAND Device Support" |
| |
| config SYS_NAND_SELF_INIT |
| bool |
| help |
| This option, if enabled, provides more flexible and linux-like |
| NAND initialization process. |
| |
| config NAND_DENALI |
| bool "Support Denali NAND controller" |
| select SYS_NAND_SELF_INIT |
| help |
| Enable support for the Denali NAND controller. |
| |
| config SYS_NAND_DENALI_64BIT |
| bool "Use 64-bit variant of Denali NAND controller" |
| depends on NAND_DENALI |
| help |
| The Denali NAND controller IP has some variations in terms of |
| the bus interface. The DMA setup sequence is completely differenct |
| between 32bit / 64bit AXI bus variants. |
| |
| If your Denali NAND controller is the 64-bit variant, say Y. |
| Otherwise (32 bit), say N. |
| |
| config NAND_DENALI_SPARE_AREA_SKIP_BYTES |
| int "Number of bytes skipped in OOB area" |
| depends on NAND_DENALI |
| range 0 63 |
| help |
| This option specifies the number of bytes to skip from the beginning |
| of OOB area before last ECC sector data starts. This is potentially |
| used to preserve the bad block marker in the OOB area. |
| |
| config NAND_VF610_NFC |
| bool "Support for Freescale NFC for VF610/MPC5125" |
| select SYS_NAND_SELF_INIT |
| help |
| Enables support for NAND Flash Controller on some Freescale |
| processors like the VF610, MPC5125, MCF54418 or Kinetis K70. |
| The driver supports a maximum 2k page size. The driver |
| currently does not support hardware ECC. |
| |
| choice |
| prompt "Hardware ECC strength" |
| depends on NAND_VF610_NFC |
| default SYS_NAND_VF610_NFC_45_ECC_BYTES |
| help |
| Select the ECC strength used in the hardware BCH ECC block. |
| |
| config SYS_NAND_VF610_NFC_45_ECC_BYTES |
| bool "24-error correction (45 ECC bytes)" |
| |
| config SYS_NAND_VF610_NFC_60_ECC_BYTES |
| bool "32-error correction (60 ECC bytes)" |
| |
| endchoice |
| |
| config NAND_PXA3XX |
| bool "Support for NAND on PXA3xx and Armada 370/XP/38x" |
| select SYS_NAND_SELF_INIT |
| help |
| This enables the driver for the NAND flash device found on |
| PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2). |
| |
| config NAND_SUNXI |
| bool "Support for NAND on Allwinner SoCs" |
| depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I |
| select SYS_NAND_SELF_INIT |
| ---help--- |
| Enable support for NAND. This option enables the standard and |
| SPL drivers. |
| The SPL driver only supports reading from the NAND using DMA |
| transfers. |
| |
| config NAND_ARASAN |
| bool "Configure Arasan Nand" |
| help |
| This enables Nand driver support for Arasan nand flash |
| controller. This uses the hardware ECC for read and |
| write operations. |
| |
| config NAND_MXS |
| bool "MXS NAND support" |
| depends on MX6 |
| help |
| This enables NAND driver for the NAND flash controller on the |
| MXS processors. |
| |
| config NAND_ZYNQ |
| bool "Support for Zynq Nand controller" |
| select SYS_NAND_SELF_INIT |
| help |
| This enables Nand driver support for Nand flash controller |
| found on Zynq SoC. |
| |
| comment "Generic NAND options" |
| |
| # Enhance depends when converting drivers to Kconfig which use this config |
| # option (mxc_nand, ndfc, omap_gpmc). |
| config SYS_NAND_BUSWIDTH_16BIT |
| bool "Use 16-bit NAND interface" |
| depends on NAND_VF610_NFC |
| help |
| Indicates that NAND device has 16-bit wide data-bus. In absence of this |
| config, bus-width of NAND device is assumed to be either 8-bit and later |
| determined by reading ONFI params. |
| Above config is useful when NAND device's bus-width information cannot |
| be determined from on-chip ONFI params, like in following scenarios: |
| - SPL boot does not support reading of ONFI parameters. This is done to |
| keep SPL code foot-print small. |
| - In current U-Boot flow using nand_init(), driver initialization |
| happens in board_nand_init() which is called before any device probe |
| (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are |
| not available while configuring controller. So a static CONFIG_NAND_xx |
| is needed to know the device's bus-width in advance. |
| |
| if SPL |
| |
| config SYS_NAND_U_BOOT_LOCATIONS |
| bool "Define U-boot binaries locations in NAND" |
| help |
| Enable CONFIG_SYS_NAND_U_BOOT_OFFS though Kconfig. |
| This option should not be enabled when compiling U-boot for boards |
| defining CONFIG_SYS_NAND_U_BOOT_OFFS in their include/configs/<board>.h |
| file. |
| |
| config SYS_NAND_U_BOOT_OFFS |
| hex "Location in NAND to read U-Boot from" |
| default 0x8000 if NAND_SUNXI |
| depends on SYS_NAND_U_BOOT_LOCATIONS |
| help |
| Set the offset from the start of the nand where u-boot should be |
| loaded from. |
| |
| config SYS_NAND_U_BOOT_OFFS_REDUND |
| hex "Location in NAND to read U-Boot from" |
| default SYS_NAND_U_BOOT_OFFS |
| depends on SYS_NAND_U_BOOT_LOCATIONS |
| help |
| Set the offset from the start of the nand where the redundant u-boot |
| should be loaded from. |
| |
| config SPL_NAND_DENALI |
| bool "Support Denali NAND controller for SPL" |
| help |
| This is a small implementation of the Denali NAND controller |
| for use on SPL. |
| |
| endif |
| |
| endmenu |