include/configs/mx6sabreauto.h

/*
 * Copyright (C) 2012 Freescale Semiconductor, Inc.
 *
 * Configuration settings for the Freescale i.MX6Q SabreAuto board.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __MX6SABREAUTO_CONFIG_H
#define __MX6SABREAUTO_CONFIG_H

#ifdef CONFIG_SPL
#include "imx6_spl.h"
#endif

#define CONFIG_MACH_TYPE	3529
#define CONFIG_MXC_UART_BASE	UART4_BASE
#define CONSOLE_DEV		"ttymxc3"

/* USB Configs */
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET	/* For OTG port */
#define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS	0

#define CONFIG_PCA953X
#define CONFIG_SYS_I2C_PCA953X_WIDTH	{ {0x30, 8}, {0x32, 8}, {0x34, 8} }

#include "mx6sabre_common.h"

/* Falcon Mode */
#ifdef CONFIG_SPL_OS_BOOT
#define CONFIG_SPL_FS_LOAD_ARGS_NAME	"args"
#define CONFIG_SPL_FS_LOAD_KERNEL_NAME	"uImage"
#define CONFIG_SYS_SPL_ARGS_ADDR       0x18000000

/* Falcon Mode - MMC support: args@1MB kernel@2MB */
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR  0x800   /* 1MB */
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (CONFIG_CMD_SPL_WRITE_SIZE / 512)
#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR        0x1000  /* 2MB */
#endif

#ifdef CONFIG_MTD_NOR_FLASH
#define CONFIG_SYS_FLASH_BASE           WEIM_ARB_BASE_ADDR
#define CONFIG_SYS_FLASH_SECT_SIZE      (128 * 1024)
#define CONFIG_SYS_MAX_FLASH_BANKS 1    /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 256   /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_CFI            /* Flash memory is CFI compliant */
#define CONFIG_FLASH_CFI_DRIVER         /* Use drivers/cfi_flash.c */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* Use buffered writes*/
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
#endif

#define CONFIG_SYS_FSL_USDHC_NUM	2
#if defined(CONFIG_ENV_IS_IN_MMC)
#define CONFIG_SYS_MMC_ENV_DEV		0
#endif

/* I2C Configs */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
#define CONFIG_SYS_I2C_SPEED		100000

/* NAND stuff */
#define CONFIG_NAND_MXS
#define CONFIG_SYS_MAX_NAND_DEVICE     1
#define CONFIG_SYS_NAND_BASE           0x40000000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_ONFI_DETECTION

/* DMA stuff, needed for GPMI/MXS NAND support */
#define CONFIG_APBH_DMA
#define CONFIG_APBH_DMA_BURST
#define CONFIG_APBH_DMA_BURST8

/* PMIC */
#define CONFIG_POWER
#define CONFIG_POWER_I2C
#define CONFIG_POWER_PFUZE100
#define CONFIG_POWER_PFUZE100_I2C_ADDR	0x08

#endif                         /* __MX6SABREAUTO_CONFIG_H */