| Stefan Roese | 6e7fb6e | 2005-11-29 18:18:21 +0100 | [diff] [blame] | 1 | #define EPLD0_FSEL_FB2 0x80 |
| 2 | #define EPLD0_BOOT_SMALL_FLASH 0x40 /* 0 boot from large flash, 1 from small flash */ |
| 3 | #define EPLD0_RAW_CARD_BIT0 0x20 /* raw card EC level */ |
| 4 | #define EPLD0_RAW_CARD_BIT1 0x10 |
| 5 | #define EPLD0_RAW_CARD_BIT2 0x08 |
| 6 | #define EPLD0_EXT_ARB_SEL_N 0x04 /* 0 select on-board ext PCI-X, 1 internal arbiter */ |
| 7 | #define EPLD0_FLASH_ONBRD_N 0x02 /* 0 small flash/SRAM active, 1 block access */ |
| 8 | #define EPLD0_FLASH_SRAM_SEL_N 0x01 /* 0 SRAM at mem top, 1 small flash at mem top */ |
| 9 | |
| 10 | #define EPLD1_CLK_CNTL0 0x80 /* FSEL-FB1 of MPC9772 */ |
| 11 | #define EPLD1_PCIX0_CNTL1 0x40 /* S*0 of 9531 */ |
| 12 | #define EPLD1_PCIX0_CNTL2 0x20 /* S*1 of 9531 */ |
| 13 | #define EPLD1_CLK_CNTL3 0x10 /* FSEL-B1 of MPC9772 */ |
| 14 | #define EPLD1_CLK_CNTL4 0x08 /* FSEL-B0 of MPC9772 */ |
| 15 | #define EPLD1_MASTER_CLOCK6 0x04 /* clock source select 6 */ |
| 16 | #define EPLD1_MASTER_CLOCK7 0x02 /* clock source select 7 */ |
| 17 | #define EPLD1_MASTER_CLOCK8 0x01 /* clock source select 8 */ |
| 18 | |
| 19 | #define EPLD2_ETH_MODE_10 0x80 /* Ethernet mode 10 (default = 1) */ |
| 20 | #define EPLD2_ETH_MODE_100 0x40 /* Ethernet mode 100 (default = 1) */ |
| 21 | #define EPLD2_ETH_MODE_1000 0x20 /* Ethernet mode 1000 (default = 1) */ |
| 22 | #define EPLD2_ETH_DUPLEX_MODE 0x10 /* Ethernet force full duplex mode */ |
| 23 | #define EPLD2_RESET_ETH_N 0x08 /* Ethernet reset (default = 1) */ |
| 24 | #define EPLD2_ETH_AUTO_NEGO 0x04 /* Ethernet auto negotiation */ |
| 25 | #define EPLD2_DEFAULT_UART_N 0x01 /* 0 select DSR DTR for UART1 */ |
| 26 | |
| 27 | #define EPLD3_STATUS_LED4 0x08 /* status LED 8 (1 = LED on) */ |
| 28 | #define EPLD3_STATUS_LED3 0x04 /* status LED 4 (1 = LED on) */ |
| 29 | #define EPLD3_STATUS_LED2 0x02 /* status LED 2 (1 = LED on) */ |
| 30 | #define EPLD3_STATUS_LED1 0x01 /* status LED 1 (1 = LED on) */ |
| 31 | |
| 32 | #define EPLD4_PCIX0_VTH1 0x80 /* PCI-X 0 VTH1 status */ |
| 33 | #define EPLD4_PCIX0_VTH2 0x40 /* PCI-X 0 VTH2 status */ |
| 34 | #define EPLD4_PCIX0_VTH3 0x20 /* PCI-X 0 VTH3 status */ |
| 35 | #define EPLD4_PCIX0_VTH4 0x10 /* PCI-X 0 VTH4 status */ |
| 36 | #define EPLD4_PCIX1_VTH1 0x08 /* PCI-X 1 VTH1 status */ |
| 37 | #define EPLD4_PCIX1_VTH2 0x04 /* PCI-X 1 VTH2 status */ |
| 38 | #define EPLD4_PCIX1_VTH3 0x02 /* PCI-X 1 VTH3 status */ |
| 39 | #define EPLD4_PCIX1_VTH4 0x01 /* PCI-X 1 VTH4 status */ |
| 40 | |
| 41 | #define EPLD5_PCIX0_INT0 0x80 /* PCIX0 INT0 status, write 0 to reset */ |
| 42 | #define EPLD5_PCIX0_INT1 0x40 /* PCIX0 INT1 status, write 0 to reset */ |
| 43 | #define EPLD5_PCIX0_INT2 0x20 /* PCIX0 INT2 status, write 0 to reset */ |
| 44 | #define EPLD5_PCIX0_INT3 0x10 /* PCIX0 INT3 status, write 0 to reset */ |
| 45 | #define EPLD5_PCIX1_INT0 0x08 /* PCIX1 INT0 status, write 0 to reset */ |
| 46 | #define EPLD5_PCIX1_INT1 0x04 /* PCIX1 INT1 status, write 0 to reset */ |
| 47 | #define EPLD5_PCIX1_INT2 0x02 /* PCIX1 INT2 status, write 0 to reset */ |
| 48 | #define EPLD5_PCIX1_INT3 0x01 /* PCIX1 INT3 status, write 0 to reset */ |
| 49 | |
| 50 | #define EPLD6_PCIX0_RESET_CTL 0x80 /* 0=enable slot reset, 1=disable slot reset */ |
| 51 | #define EPLD6_PCIX1_RESET_CTL 0x40 /* 0=enable slot reset, 1=disable slot reset */ |
| 52 | #define EPLD6_ETH_INT_MODE 0x20 /* 0=IRQ5 recv's external eth int */ |
| 53 | #define EPLD6_PCIX2_RESET_CTL 0x10 /* 0=enable slot reset, 1=disable slot reset */ |
| 54 | #define EPLD6_PCI1_CLKCNTL1 0x80 /* PCI1 clock control S*0 of 9531 */ |
| 55 | #define EPLD6_PCI1_CLKCNTL2 0x40 /* PCI1 clock control S*1 of 9531 */ |
| 56 | #define EPLD6_PCI2_CLKCNTL1 0x20 /* PCI2 clock control S*0 of 9531 */ |
| 57 | #define EPLD6_PCI2_CLKCNTL2 0x10 /* PCI2 clock control S*1 of 9531 */ |
| 58 | |
| 59 | #define EPLD7_VTH1 0x80 /* PCI2 VTH1 status */ |
| 60 | #define EPLD7_VTH2 0x40 /* PCI2 VTH2 status */ |
| 61 | #define EPLD7_VTH3 0x20 /* PCI2 VTH3 status */ |
| 62 | #define EPLD7_VTH4 0x10 /* PCI2 VTH4 status */ |
| 63 | #define EPLD7_INTA_MODE 0x80 /* see S5 on SW2 for details */ |
| 64 | #define EPLD7_PCI_INT_MODE_N 0x40 /* see S1 on SW2 for details */ |
| 65 | #define EPLD7_WRITE_ENABLE_GPIO 0x20 /* see S2 on SW2 for details */ |
| 66 | #define EPLD7_WRITE_ENABLE_INT 0x10 /* see S3 on SW2 for details */ |
| 67 | |
| 68 | |
| 69 | typedef struct { |
| 70 | unsigned char status; /* misc status */ |
| 71 | unsigned char clock; /* clock status, PCI-X clock control */ |
| 72 | unsigned char ethuart; /* Ethernet, UART status */ |
| 73 | unsigned char leds; /* LED register */ |
| 74 | unsigned char vth01; /* PCI0, PCI1 VTH register */ |
| 75 | unsigned char pciints; /* PCI0, PCI1 interrupts */ |
| 76 | unsigned char pci2; /* PCI2 interrupts, clock control */ |
| 77 | unsigned char vth2; /* PCI2 VTH register */ |
| 78 | unsigned char filler1[4096-8]; |
| 79 | unsigned char gpio00; /* GPIO bits 0-7 */ |
| 80 | unsigned char gpio08; /* GPIO bits 8-15 */ |
| 81 | unsigned char gpio16; /* GPIO bits 16-23 */ |
| 82 | unsigned char gpio24; /* GPIO bits 24-31 */ |
| 83 | unsigned char filler2[4096-4]; |
| 84 | unsigned char version; /* EPLD version */ |
| 85 | } epld_t; |