blob: 2070a9b1bdc059c1d7a0d729994d0e4d257d3585 [file] [log] [blame]
Albert ARIBAUD7202e8a2012-11-26 11:27:37 +00001/*
2 * Copyright (C) 2011 Albert ARIBAUD <albert.u.boot@aribaud.net>
3 *
4 * Based on the netspace_v2 code which is
5 * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
6 *
Wolfgang Denk1a459662013-07-08 09:37:19 +02007 * SPDX-License-Identifier: GPL-2.0+
Albert ARIBAUD7202e8a2012-11-26 11:27:37 +00008 */
9
10#ifndef _CONFIG_WIRELESS_SPACE_H
11#define _CONFIG_WIRELESS_SPACE_H
12
13/*
14 * Machine number definition
15 */
16#define MACH_TYPE_WIRELESS_SPACE 2500 /* is missing in mach-types.h */
17#define CONFIG_MACH_TYPE MACH_TYPE_WIRELESS_SPACE
18#define CONFIG_IDENT_STRING " Wireless Space"
19
20/*
21 * High Level Configuration Options (easy to change)
22 */
23#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */
24#define CONFIG_KIRKWOOD /* SoC Family Name */
25/* SoC name */
26#define CONFIG_KW88F6281
27#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
28
29/*
30 * Commands configuration
31 */
32#define CONFIG_SYS_NO_FLASH /* no NOR or SPI flash */
33#include <config_cmd_default.h>
34#define CONFIG_CMD_ENV
35#define CONFIG_CMD_DHCP
36#define CONFIG_CMD_PING
37#define CONFIG_CMD_NAND
38#define CONFIG_CMD_I2C
39#define CONFIG_CMD_IDE
40#define CONFIG_CMD_USB
41
42/*
43 * Core clock definition
44 */
45#define CONFIG_SYS_TCLK 166000000 /* 166MHz */
46
47/*
48 * SDRAM configuration
49 */
50#define CONFIG_NR_DRAM_BANKS 1
51
52/*
53 * Different SDRAM configuration and size for some of the boards derived
54 * from the Network Space v2
55 */
56
57/*
58 * mv-common.h should be defined after CMD configs since it used them
59 * to enable certain macros
60 */
61#include "mv-common.h"
62
63/* Remove or override few declarations from mv-common.h */
64#undef CONFIG_RBTREE
65#undef CONFIG_SYS_IDE_MAXBUS
66#undef CONFIG_SYS_IDE_MAXDEVICE
67#define CONFIG_SYS_IDE_MAXBUS 1
68#define CONFIG_SYS_IDE_MAXDEVICE 1
69#undef CONFIG_SYS_PROMPT
70#define CONFIG_SYS_PROMPT "ws> "
71
72/*
73 * Ethernet Driver configuration
74 */
75#ifdef CONFIG_CMD_NET
76#define CONFIG_MISC_INIT_R /* misc_init_r() initializes MAC address */
77#define CONFIG_MVGBE_PORTS {1, 0} /* enable only egiga0... */
78#define PORT_SERIAL_CONTROL_VALUE 0x00A4260E /* ... tied to the switch... */
79#define CONFIG_PHY_BASE_ADR 0xa /* ... through a 'fake' PHY */
80#define CONFIG_MII
81#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
82#define CONFIG_NETCONSOLE
83#define CONFIG_MV88E61XX_SWITCH
84#define CONFIG_MV88E61XX_MULTICHIP_ADRMODE
85#define CONFIG_MV88E61XX_CMD
86#define CONFIG_CMD_TFTPPUT
87#endif /* CONFIG_CMD_NET */
88
89/*
90 * SATA Driver configuration
91 */
92#ifdef CONFIG_MVSATA_IDE
93#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
94#endif /* CONFIG_MVSATA_IDE */
95
96/*
97 * Enable GPI0 support
98 */
99#define CONFIG_KIRKWOOD_GPIO
100
101/*
102 * Enable I2C support
103 */
104#ifdef CONFIG_CMD_I2C
105/* I2C EEPROM HT24LC04 (512B - 32 pages of 16 Bytes) */
106#define CONFIG_CMD_EEPROM
107#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
108#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-byte page size */
109#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* 8-bit device address */
110#endif /* CONFIG_CMD_I2C */
111
112/*
113 * Partition support
114 */
115#define CONFIG_DOS_PARTITION
116#define CONFIG_EFI_PARTITION
117
118/*
119 * File systems support
120 */
121#define CONFIG_CMD_EXT2
122#define CONFIG_CMD_FAT
123
124/*
125 * Use the HUSH parser
126 */
127#define CONFIG_SYS_HUSH_PARSER
128
129/*
130 * Console configuration
131 */
132#define CONFIG_CONSOLE_MUX
133#define CONFIG_SYS_CONSOLE_IS_IN_ENV
134
135/*
136 * Enable device tree support
137 */
138#define CONFIG_OF_LIBFDT
139
140/*
141 * Environment variables configurations
142 */
143
144#define CONFIG_ENV_IS_IN_NAND
145#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128KB */
146#define CONFIG_ENV_SIZE 0x20000 /* 128KB */
147#define CONFIG_ENV_OFFSET 0x80000 /* env starts here */
148
149/*
150 * Board-specific command to make using buttons etc easier
151 */
152
153#define CONFIG_WIRELESS_SPACE_CMD
154
155/*
156 * Default environment variables
157 */
158#define CONFIG_PREBOOT
159
160#define CONFIG_BOOTARGS "console=ttyS0,115200"
161
162#define CONFIG_BOOTCOMMAND \
163 "if run usbload || run diskload; then bootm; fi"
164
165#define CONFIG_EXTRA_ENV_SETTINGS \
166 "stdin=serial\0" \
167 "stdout=serial\0" \
168 "stderr=serial\0" \
169 "bootfile=uImage\0" \
170 "loadaddr=0x800000\0" \
171 "autoload=no\0" \
172 "netconsole=" \
173 "set stdin $stdin,nc; " \
174 "set stdout $stdout,nc; " \
175 "set stderr $stderr,nc;\0" \
176 "diskload=ide reset && " \
177 "ext2load ide 0:1 $loadaddr /boot/$bootfile\0" \
178 "usbload=usb start && " \
179 "fatload usb 0:1 $loadaddr /boot/$bootfile\0" \
180 "preboot=" \
181 "dhcp && run netconsole\0"
182
183#endif /* _CONFIG_WIRELESS_SPACE_H */