include/configs/sama5d3_xplained.h

/*
 * Configuration settings for the SAMA5D3 Xplained board.
 *
 * Copyright (C) 2014 Atmel Corporation
 *		      Bo Shen <voice.shen@atmel.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/* No NOR flash, this definition should put before common header */
#define CONFIG_SYS_NO_FLASH

#include "at91-sama5_common.h"

/* serial console */
#define CONFIG_ATMEL_USART
#define CONFIG_USART_BASE		ATMEL_BASE_DBGU
#define CONFIG_USART_ID			ATMEL_ID_DBGU

/*
 * This needs to be defined for the OHCI code to work but it is defined as
 * ATMEL_ID_UHPHS in the CPU specific header files.
 */
#define ATMEL_ID_UHP			ATMEL_ID_UHPHS

/*
 * Specify the clock enable bit in the PMC_SCER register.
 */
#define ATMEL_PMC_UHP			AT91SAM926x_PMC_UHP

/* SDRAM */
#define CONFIG_NR_DRAM_BANKS		1
#define CONFIG_SYS_SDRAM_BASE           ATMEL_BASE_DDRCS
#define CONFIG_SYS_SDRAM_SIZE		0x10000000

#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_INIT_SP_ADDR		0x310000
#else
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
#endif

/* NAND flash */
#define CONFIG_CMD_NAND

#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_ATMEL
#define CONFIG_SYS_MAX_NAND_DEVICE	1
#define CONFIG_SYS_NAND_BASE		ATMEL_BASE_CS3
/* our ALE is AD21 */
#define CONFIG_SYS_NAND_MASK_ALE	(1 << 21)
/* our CLE is AD22 */
#define CONFIG_SYS_NAND_MASK_CLE	(1 << 22)
#define CONFIG_SYS_NAND_ONFI_DETECTION
/* PMECC & PMERRLOC */
#define CONFIG_ATMEL_NAND_HWECC
#define CONFIG_ATMEL_NAND_HW_PMECC
#define CONFIG_PMECC_CAP		4
#define CONFIG_PMECC_SECTOR_SIZE	512
#define CONFIG_CMD_NAND_TRIMFFS
#define CONFIG_CMD_MTDPARTS

#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
#define CONFIG_RBTREE
#define CONFIG_LZO
#define CONFIG_CMD_UBIFS
#endif

/* Ethernet Hardware */
#define CONFIG_MACB
#define CONFIG_RMII
#define CONFIG_NET_RETRY_COUNT		20
#define CONFIG_MACB_SEARCH_PHY
#define CONFIG_RGMII
#define CONFIG_PHYLIB

/* MMC */

#ifdef CONFIG_CMD_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_GENERIC_ATMEL_MCI
#define CONFIG_ATMEL_MCI_8BIT
#endif

/* USB */

#ifdef CONFIG_CMD_USB
#define CONFIG_USB_ATMEL
#define CONFIG_USB_ATMEL_CLK_SEL_UPLL
#define CONFIG_USB_OHCI_NEW
#define CONFIG_SYS_USB_OHCI_CPU_INIT
#define CONFIG_SYS_USB_OHCI_REGS_BASE		ATMEL_BASE_OHCI
#define CONFIG_SYS_USB_OHCI_SLOT_NAME		"SAMA5D3 Xplained"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	2
#define CONFIG_DOS_PARTITION
#endif

#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
#define CONFIG_FAT_WRITE
#endif

#define CONFIG_SYS_LOAD_ADDR			0x22000000 /* load address */

#if CONFIG_SYS_USE_NANDFLASH
/* override the bootcmd, bootargs and other configuration for nandflash env */
#elif CONFIG_SYS_USE_MMC
/* override the bootcmd, bootargs and other configuration for sd/mmc env */
#else
#define CONFIG_ENV_IS_NOWHERE
#endif

/* SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE		0x300000
#define CONFIG_SPL_MAX_SIZE		0x10000
#define CONFIG_SPL_BSS_START_ADDR	0x20000000
#define CONFIG_SPL_BSS_MAX_SIZE		0x80000
#define CONFIG_SYS_SPL_MALLOC_START	0x20080000
#define CONFIG_SYS_SPL_MALLOC_SIZE	0x80000

#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SYS_MONITOR_LEN		(512 << 10)

#ifdef CONFIG_SYS_USE_MMC
#define CONFIG_SPL_LDSCRIPT		arch/arm/mach-at91/armv7/u-boot-spl.lds
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME	"u-boot.img"

#elif CONFIG_SYS_USE_NANDFLASH
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SYS_NAND_U_BOOT_OFFS	0x40000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_SIZE	0x800
#define CONFIG_SYS_NAND_PAGE_COUNT	64
#define CONFIG_SYS_NAND_OOBSIZE		64
#define CONFIG_SYS_NAND_BLOCK_SIZE	0x20000
#define CONFIG_SYS_NAND_BAD_BLOCK_POS	0x0
#define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER

#endif

#endif