blob: 33428803eb77882ee1c69d5b8952cd0618c046f4 [file] [log] [blame]
Peter Tyser1f03cbf2008-12-23 16:32:00 -06001/*
2 * Copyright 2008 Extreme Engineering Solutions, Inc.
3 * Copyright 2004-2008 Freescale Semiconductor, Inc.
4 *
Wolfgang Denk1a459662013-07-08 09:37:19 +02005 * SPDX-License-Identifier: GPL-2.0+
Peter Tyser1f03cbf2008-12-23 16:32:00 -06006 */
7
8/*
Peter Tyserc00ac252010-10-22 00:20:26 -05009 * xpedite520x board configuration file
Peter Tyser1f03cbf2008-12-23 16:32:00 -060010 */
11#ifndef __CONFIG_H
12#define __CONFIG_H
13
14/*
15 * High Level Configuration Options
16 */
17#define CONFIG_BOOKE 1 /* BOOKE */
18#define CONFIG_E500 1 /* BOOKE e500 family */
19#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */
20#define CONFIG_MPC8548 1
21#define CONFIG_XPEDITE5200 1
22#define CONFIG_SYS_BOARD_NAME "XPedite5200"
John Schmoller92af65492010-10-22 00:20:24 -050023#define CONFIG_SYS_FORM_PMC_XMC 1
Peter Tyser1f03cbf2008-12-23 16:32:00 -060024#define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */
Peter Tyser1f03cbf2008-12-23 16:32:00 -060025
Wolfgang Denk2ae18242010-10-06 09:05:45 +020026#ifndef CONFIG_SYS_TEXT_BASE
27#define CONFIG_SYS_TEXT_BASE 0xfff80000
28#endif
29
Peter Tyser1f03cbf2008-12-23 16:32:00 -060030#define CONFIG_PCI 1 /* Enable PCI/PCIE */
31#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */
32#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
33#define CONFIG_PCI1 1 /* PCI controller 1 */
34#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
Gabor Juhos842033e2013-05-30 07:06:12 +000035#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
Peter Tyser1f03cbf2008-12-23 16:32:00 -060036#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
37#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
38
39/*
40 * DDR config
41 */
42#define CONFIG_FSL_DDR2
43#undef CONFIG_FSL_DDR_INTERACTIVE
44#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
45#define CONFIG_DDR_SPD
46#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
47#define SPD_EEPROM_ADDRESS 0x54
48#define CONFIG_NUM_DDR_CONTROLLERS 1
49#define CONFIG_DIMM_SLOTS_PER_CTLR 1
50#define CONFIG_CHIP_SELECTS_PER_CTRL 2
51#define CONFIG_DDR_ECC
52#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
53#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
54#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
55#define CONFIG_VERY_BIG_RAM
56
57#define CONFIG_SYS_CLK_FREQ 66666666
58
59/*
60 * These can be toggled for performance analysis, otherwise use default.
61 */
62#define CONFIG_L2_CACHE /* toggle L2 cache */
63#define CONFIG_BTB /* toggle branch predition */
64#define CONFIG_ENABLE_36BIT_PHYS 1
65
Timur Tabie46fedf2011-08-04 18:03:41 -050066#define CONFIG_SYS_CCSRBAR 0xef000000
67#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
Peter Tyser1f03cbf2008-12-23 16:32:00 -060068
69/*
70 * Diagnostics
71 */
72#define CONFIG_SYS_ALT_MEMTEST
73#define CONFIG_SYS_MEMTEST_START 0x10000000
74#define CONFIG_SYS_MEMTEST_END 0x20000000
Peter Tyser66a8b442010-10-22 00:20:33 -050075#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
76 CONFIG_SYS_POST_I2C)
77#define I2C_ADDR_LIST {CONFIG_SYS_I2C_MAX1237_ADDR, \
78 CONFIG_SYS_I2C_EEPROM_ADDR, \
79 CONFIG_SYS_I2C_PCA953X_ADDR0, \
80 CONFIG_SYS_I2C_PCA953X_ADDR1, \
81 CONFIG_SYS_I2C_RTC_ADDR}
Peter Tyser1f03cbf2008-12-23 16:32:00 -060082
83/*
84 * Memory map
85 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
86 * 0x8000_0000 0xbfff_ffff PCI1 Mem 1G non-cacheable
87 * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable
88 * 0xe800_0000 0xe87f_ffff PCI1 IO 8M non-cacheable
89 * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable
90 * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable
91 * 0xf800_0000 0xfbff_ffff NOR Flash 2 64M non-cacheable
92 * 0xfc00_0000 0xffff_ffff NOR Flash 1 64M non-cacheable
93 */
94
Kumar Gala202d9482009-09-15 22:21:58 -050095#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3)
Peter Tyser1f03cbf2008-12-23 16:32:00 -060096
97/*
98 * NAND flash configuration
99 */
100#define CONFIG_SYS_NAND_BASE 0xef800000
101#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */
102#define CONFIG_SYS_MAX_NAND_DEVICE 1
103#define CONFIG_NAND_ACTL
104#define CONFIG_SYS_NAND_ACTL_CLE (1 << 3) /* ADDR3 is CLE */
105#define CONFIG_SYS_NAND_ACTL_ALE (1 << 4) /* ADDR4 is ALE */
106#define CONFIG_SYS_NAND_ACTL_NCE (0) /* NCE not controlled by ADDR */
107#define CONFIG_SYS_NAND_ACTL_DELAY 25
108
109/*
110 * NOR flash configuration
111 */
112#define CONFIG_SYS_FLASH_BASE 0xfc000000
113#define CONFIG_SYS_FLASH_BASE2 0xf8000000
114#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
115#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
116#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
117#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
118#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
119#define CONFIG_FLASH_CFI_DRIVER
120#define CONFIG_SYS_FLASH_CFI
Peter Tyser5ff82102009-07-19 19:17:40 -0500121#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600122#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \
123 {0xfbf40000, 0xc0000} }
Wolfgang Denk14d0a022010-10-07 21:51:12 +0200124#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600125
126/*
127 * Chip select configuration
128 */
129/* NOR Flash 0 on CS0 */
130#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \
131 BR_PS_16 | \
132 BR_V)
133#define CONFIG_SYS_OR0_PRELIM (OR_AM_64MB | \
134 OR_GPCM_ACS_DIV4 | \
135 OR_GPCM_SCY_8)
136
137/* NOR Flash 1 on CS1 */
138#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \
139 BR_PS_16 | \
140 BR_V)
141#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
142
143/* NAND flash on CS2 */
144#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \
145 BR_PS_8 | \
146 BR_V)
147
148/* NAND flash on CS2 */
149#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \
150 OR_GPCM_BCTLD | \
151 OR_GPCM_CSNT | \
152 OR_GPCM_ACS_DIV4 | \
153 OR_GPCM_SCY_4 | \
154 OR_GPCM_TRLX | \
155 OR_GPCM_EHTR)
156
157/* NAND flash on CS3 */
158#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \
159 BR_PS_8 | \
160 BR_V)
161#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
162
163/*
164 * Use L1 as initial stack
165 */
166#define CONFIG_SYS_INIT_RAM_LOCK 1
167#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000
Wolfgang Denk553f0982010-10-26 13:32:32 +0200168#define CONFIG_SYS_INIT_RAM_SIZE 0x4000
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600169
Wolfgang Denk25ddd1f2010-10-26 14:34:52 +0200170#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600171#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
172
173#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
174#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
175
176/*
177 * Serial Port
178 */
179#define CONFIG_CONS_INDEX 1
180#define CONFIG_SYS_NS16550
181#define CONFIG_SYS_NS16550_SERIAL
182#define CONFIG_SYS_NS16550_REG_SIZE 1
183#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
184#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
185#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
186#define CONFIG_SYS_BAUDRATE_TABLE \
187 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
188#define CONFIG_BAUDRATE 115200
189#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
190#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
191
192/*
193 * Use the HUSH parser
194 */
195#define CONFIG_SYS_HUSH_PARSER
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600196
197/*
198 * Pass open firmware flat tree
199 */
200#define CONFIG_OF_LIBFDT 1
201#define CONFIG_OF_BOARD_SETUP 1
202#define CONFIG_OF_STDOUT_VIA_ALIAS 1
203
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600204/*
205 * I2C
206 */
Heiko Schocher00f792e2012-10-24 13:48:22 +0200207#define CONFIG_SYS_I2C
208#define CONFIG_SYS_I2C_FSL
209#define CONFIG_SYS_FSL_I2C_SPEED 400000
210#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
211#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
212#define CONFIG_SYS_FSL_I2C2_SPEED 400000
213#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
214#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600215
216/* I2C EEPROM */
217#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
218#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
219#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */
220#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */
221
222/* I2C RTC */
223#define CONFIG_RTC_M41T11 1
224#define CONFIG_SYS_I2C_RTC_ADDR 0x68
225#define CONFIG_SYS_M41T11_BASE_YEAR 2000
226
227/* GPIO */
228#define CONFIG_PCA953X
229#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18
230#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x19
231#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0
232
233/* PCA957 @ 0x18 */
234#define CONFIG_SYS_PCA953X_BRD_CFG0 0x01
235#define CONFIG_SYS_PCA953X_BRD_CFG1 0x02
236#define CONFIG_SYS_PCA953X_BRD_CFG2 0x04
237#define CONFIG_SYS_PCA953X_XMC_ROOT0 0x08
238#define CONFIG_SYS_PCA953X_FLASH_PASS_CS 0x10
John Schmoller72fb68d2010-10-22 00:20:25 -0500239#define CONFIG_SYS_PCA953X_NVM_WP 0x20
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600240#define CONFIG_SYS_PCA953X_MONARCH 0x40
241#define CONFIG_SYS_PCA953X_EREADY 0x80
242
243/* PCA957 @ 0x19 */
244#define CONFIG_SYS_PCA953X_P14_IO0 0x01
245#define CONFIG_SYS_PCA953X_P14_IO1 0x02
246#define CONFIG_SYS_PCA953X_P14_IO2 0x04
247#define CONFIG_SYS_PCA953X_P14_IO3 0x08
248#define CONFIG_SYS_PCA953X_P14_IO4 0x10
249#define CONFIG_SYS_PCA953X_P14_IO5 0x20
250#define CONFIG_SYS_PCA953X_P14_IO6 0x40
251#define CONFIG_SYS_PCA953X_P14_IO7 0x80
252
Peter Tyser66a8b442010-10-22 00:20:33 -0500253/* 12-bit ADC used to measure CPU diode */
254#define CONFIG_SYS_I2C_MAX1237_ADDR 0x34
255
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600256/*
257 * General PCI
258 * Memory space is mapped 1-1, but I/O space must start from 0.
259 */
Peter Tyser9660c5d2010-10-22 00:20:22 -0500260#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000
261#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BUS
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600262#define CONFIG_SYS_PCI1_MEM_SIZE 0x40000000 /* 1G */
Peter Tyser9660c5d2010-10-22 00:20:22 -0500263#define CONFIG_SYS_PCI1_IO_BUS 0x00000000
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600264#define CONFIG_SYS_PCI1_IO_PHYS 0xe8000000
265#define CONFIG_SYS_PCI1_IO_SIZE 0x00800000 /* 1M */
266
267/*
268 * Networking options
269 */
270#define CONFIG_TSEC_ENET /* tsec ethernet support */
271#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600272#define CONFIG_MII 1 /* MII PHY management */
273#define CONFIG_ETHPRIME "eTSEC1"
274
275#define CONFIG_TSEC1 1
276#define CONFIG_TSEC1_NAME "eTSEC1"
277#define TSEC1_FLAGS TSEC_GIGABIT
278#define TSEC1_PHY_ADDR 1
279#define TSEC1_PHYIDX 0
280#define CONFIG_HAS_ETH0
281
282#define CONFIG_TSEC2 1
283#define CONFIG_TSEC2_NAME "eTSEC2"
284#define TSEC2_FLAGS TSEC_GIGABIT
285#define TSEC2_PHY_ADDR 2
286#define TSEC2_PHYIDX 0
287#define CONFIG_HAS_ETH1
288
289#define CONFIG_TSEC3 1
290#define CONFIG_TSEC3_NAME "eTSEC3"
291#define TSEC3_FLAGS TSEC_GIGABIT
292#define TSEC3_PHY_ADDR 3
293#define TSEC3_PHYIDX 0
294#define CONFIG_HAS_ETH2
295
296#define CONFIG_TSEC4 1
297#define CONFIG_TSEC4_NAME "eTSEC4"
298#define TSEC4_FLAGS TSEC_GIGABIT
299#define TSEC4_PHY_ADDR 4
300#define TSEC4_PHYIDX 0
301#define CONFIG_HAS_ETH3
302
303/*
304 * BOOTP options
305 */
306#define CONFIG_BOOTP_BOOTFILESIZE
307#define CONFIG_BOOTP_BOOTPATH
308#define CONFIG_BOOTP_GATEWAY
309
310/*
311 * Command configuration.
312 */
313#include <config_cmd_default.h>
314
315#define CONFIG_CMD_ASKENV
316#define CONFIG_CMD_DATE
317#define CONFIG_CMD_DHCP
318#define CONFIG_CMD_EEPROM
319#define CONFIG_CMD_ELF
Mike Frysingerbdab39d2009-01-28 19:08:14 -0500320#define CONFIG_CMD_SAVEENV
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600321#define CONFIG_CMD_FLASH
322#define CONFIG_CMD_I2C
323#define CONFIG_CMD_JFFS2
324#define CONFIG_CMD_MII
325#define CONFIG_CMD_NAND
326#define CONFIG_CMD_NET
327#define CONFIG_CMD_PCA953X
328#define CONFIG_CMD_PCA953X_INFO
329#define CONFIG_CMD_PCI
John Schmoller96d61602010-10-22 00:20:23 -0500330#define CONFIG_CMD_PCI_ENUM
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600331#define CONFIG_CMD_PING
332#define CONFIG_CMD_SNTP
Becky Bruce199e2622010-06-17 11:37:25 -0500333#define CONFIG_CMD_REGINFO
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600334
335/*
336 * Miscellaneous configurable options
337 */
338#define CONFIG_SYS_LONGHELP /* undef to save memory */
339#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600340#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
341#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
342#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
343#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600344#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
Kim Phillips5be58f52010-07-14 19:47:18 -0500345#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600346#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */
347#define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */
348#define CONFIG_PANIC_HANG /* do not reset board on panic */
349#define CONFIG_PREBOOT /* enable preboot variable */
350#define CONFIG_FIT 1
351#define CONFIG_FIT_VERBOSE 1
352#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */
353#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
354
355/*
356 * For booting Linux, the board info and command line data
357 * have to be in the first 16 MB of memory, since this is
358 * the maximum mapped by the Linux kernel during initialization.
359 */
360#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
Peter Tyser39121c02009-07-21 13:51:07 -0500361#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600362
363/*
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600364 * Environment Configuration
365 */
366#define CONFIG_ENV_IS_IN_FLASH 1
367#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */
368#define CONFIG_ENV_SIZE 0x8000
369#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024))
370
371/*
372 * Flash memory map:
373 * fff80000 - ffffffff Pri U-Boot (512 KB)
374 * fff40000 - fff7ffff Pri U-Boot Environment (256 KB)
375 * fff00000 - fff3ffff Pri FDT (256KB)
376 * fef00000 - ffefffff Pri OS image (16MB)
377 * fc000000 - feefffff Pri OS Use/Filesystem (47MB)
378 *
379 * fbf80000 - fbffffff Sec U-Boot (512 KB)
380 * fbf40000 - fbf7ffff Sec U-Boot Environment (256 KB)
381 * fbf00000 - fbf3ffff Sec FDT (256KB)
382 * faf00000 - fbefffff Sec OS image (16MB)
383 * f8000000 - faefffff Sec OS Use/Filesystem (47MB)
384 */
Marek Vasut5368c552012-09-23 17:41:24 +0200385#define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000)
386#define CONFIG_UBOOT2_ENV_ADDR __stringify(0xfbf80000)
387#define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000)
388#define CONFIG_FDT2_ENV_ADDR __stringify(0xfbf00000)
389#define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000)
390#define CONFIG_OS2_ENV_ADDR __stringify(0xfaf00000)
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600391
392#define CONFIG_PROG_UBOOT1 \
393 "$download_cmd $loadaddr $ubootfile; " \
394 "if test $? -eq 0; then " \
395 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
396 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
397 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \
398 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
399 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \
400 "if test $? -ne 0; then " \
401 "echo PROGRAM FAILED; " \
402 "else; " \
403 "echo PROGRAM SUCCEEDED; " \
404 "fi; " \
405 "else; " \
406 "echo DOWNLOAD FAILED; " \
407 "fi;"
408
409#define CONFIG_PROG_UBOOT2 \
410 "$download_cmd $loadaddr $ubootfile; " \
411 "if test $? -eq 0; then " \
412 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
413 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
414 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \
415 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
416 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \
417 "if test $? -ne 0; then " \
418 "echo PROGRAM FAILED; " \
419 "else; " \
420 "echo PROGRAM SUCCEEDED; " \
421 "fi; " \
422 "else; " \
423 "echo DOWNLOAD FAILED; " \
424 "fi;"
425
426#define CONFIG_BOOT_OS_NET \
427 "$download_cmd $osaddr $osfile; " \
428 "if test $? -eq 0; then " \
429 "if test -n $fdtaddr; then " \
430 "$download_cmd $fdtaddr $fdtfile; " \
431 "if test $? -eq 0; then " \
432 "bootm $osaddr - $fdtaddr; " \
433 "else; " \
434 "echo FDT DOWNLOAD FAILED; " \
435 "fi; " \
436 "else; " \
437 "bootm $osaddr; " \
438 "fi; " \
439 "else; " \
440 "echo OS DOWNLOAD FAILED; " \
441 "fi;"
442
443#define CONFIG_PROG_OS1 \
444 "$download_cmd $osaddr $osfile; " \
445 "if test $? -eq 0; then " \
446 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \
447 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
448 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
449 "if test $? -ne 0; then " \
450 "echo OS PROGRAM FAILED; " \
451 "else; " \
452 "echo OS PROGRAM SUCCEEDED; " \
453 "fi; " \
454 "else; " \
455 "echo OS DOWNLOAD FAILED; " \
456 "fi;"
457
458#define CONFIG_PROG_OS2 \
459 "$download_cmd $osaddr $osfile; " \
460 "if test $? -eq 0; then " \
461 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \
462 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
463 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
464 "if test $? -ne 0; then " \
465 "echo OS PROGRAM FAILED; " \
466 "else; " \
467 "echo OS PROGRAM SUCCEEDED; " \
468 "fi; " \
469 "else; " \
470 "echo OS DOWNLOAD FAILED; " \
471 "fi;"
472
473#define CONFIG_PROG_FDT1 \
474 "$download_cmd $fdtaddr $fdtfile; " \
475 "if test $? -eq 0; then " \
476 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \
477 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
478 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
479 "if test $? -ne 0; then " \
480 "echo FDT PROGRAM FAILED; " \
481 "else; " \
482 "echo FDT PROGRAM SUCCEEDED; " \
483 "fi; " \
484 "else; " \
485 "echo FDT DOWNLOAD FAILED; " \
486 "fi;"
487
488#define CONFIG_PROG_FDT2 \
489 "$download_cmd $fdtaddr $fdtfile; " \
490 "if test $? -eq 0; then " \
491 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \
492 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
493 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
494 "if test $? -ne 0; then " \
495 "echo FDT PROGRAM FAILED; " \
496 "else; " \
497 "echo FDT PROGRAM SUCCEEDED; " \
498 "fi; " \
499 "else; " \
500 "echo FDT DOWNLOAD FAILED; " \
501 "fi;"
502
503#define CONFIG_EXTRA_ENV_SETTINGS \
504 "autoload=yes\0" \
505 "download_cmd=tftp\0" \
506 "console_args=console=ttyS0,115200\0" \
507 "root_args=root=/dev/nfs rw\0" \
508 "misc_args=ip=on\0" \
509 "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
510 "bootfile=/home/user/file\0" \
Peter Tyserc00ac252010-10-22 00:20:26 -0500511 "osfile=/home/user/board.uImage\0" \
512 "fdtfile=/home/user/board.dtb\0" \
Peter Tyser1f03cbf2008-12-23 16:32:00 -0600513 "ubootfile=/home/user/u-boot.bin\0" \
514 "fdtaddr=c00000\0" \
515 "osaddr=0x1000000\0" \
516 "loadaddr=0x1000000\0" \
517 "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \
518 "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \
519 "prog_os1="CONFIG_PROG_OS1"\0" \
520 "prog_os2="CONFIG_PROG_OS2"\0" \
521 "prog_fdt1="CONFIG_PROG_FDT1"\0" \
522 "prog_fdt2="CONFIG_PROG_FDT2"\0" \
523 "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \
524 "bootcmd_flash1=run set_bootargs; " \
525 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
526 "bootcmd_flash2=run set_bootargs; " \
527 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
528 "bootcmd=run bootcmd_flash1\0"
529#endif /* __CONFIG_H */