board/xes/xpedite1000/xpedite1000.c

/*
 * Copyright (C) 2003 Travis B. Sawyer <travis.sawyer@sandburst.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <common.h>
#include <console.h>
#include <asm/processor.h>
#include <spd_sdram.h>
#include <i2c.h>
#include <net.h>

DECLARE_GLOBAL_DATA_PTR;

int board_early_init_f(void)
{
	unsigned long sdrreg;

	/*
	 * Enable GPIO for pins 18 - 24
	 * 18 = SEEPROM_WP
	 * 19 = #M_RST
	 * 20 = #MONARCH
	 * 21 = #LED_ALARM
	 * 22 = #LED_ACT
	 * 23 = #LED_STATUS1
	 * 24 = #LED_STATUS2
	 */
	mfsdr(SDR0_PFC0, sdrreg);
	mtsdr(SDR0_PFC0, (sdrreg & ~SDR0_PFC0_TRE_ENABLE) | 0x00003e00);
	out32(CONFIG_SYS_GPIO_BASE + 0x018, (USR_LED0 | USR_LED1 | USR_LED2 | USR_LED3));
	LED0_OFF();
	LED1_OFF();
	LED2_OFF();
	LED3_OFF();

	/* Setup the external bus controller/chip selects */
	mtebc(PB0AP, 0x04055200);	/* 16MB Strata FLASH */
	mtebc(PB0CR, 0xff098000);	/* BAS=0xff0 16MB R/W 8-bit */
	mtebc(PB1AP, 0x04055200);	/* 512KB Socketed AMD FLASH */
	mtebc(PB1CR, 0xfe018000);	/* BAS=0xfe0 1MB R/W 8-bit */
	mtebc(PB6AP, 0x05006400);	/* 32-64MB AMD MirrorBit FLASH */
	mtebc(PB6CR, 0xf00da000);	/* BAS=0xf00 64MB R/W i6-bit */
	mtebc(PB7AP, 0x05006400);	/* 32-64MB AMD MirrorBit FLASH */
	mtebc(PB7CR, 0xf40da000);	/* BAS=0xf40 64MB R/W 16-bit */

	/*
	 * Setup the interrupt controller polarities, triggers, etc.
	 *
	 * Because of the interrupt handling rework to handle 440GX interrupts
	 * with the common code, we needed to change names of the UIC registers.
	 * Here the new relationship:
	 *
	 * U-Boot name	440GX name
	 * -----------------------
	 * UIC0		UICB0
	 * UIC1		UIC0
	 * UIC2		UIC1
	 * UIC3		UIC2
	 */
	mtdcr(UIC1SR, 0xffffffff);	/* clear all */
	mtdcr(UIC1ER, 0x00000000);	/* disable all */
	mtdcr(UIC1CR, 0x00000003);	/* SMI & UIC1 crit are critical */
	mtdcr(UIC1PR, 0xfffffe00);	/* per ref-board manual */
	mtdcr(UIC1TR, 0x01c00000);	/* per ref-board manual */
	mtdcr(UIC1VR, 0x00000001);	/* int31 highest, base=0x000 */
	mtdcr(UIC1SR, 0xffffffff);	/* clear all */

	mtdcr(UIC2SR, 0xffffffff);	/* clear all */
	mtdcr(UIC2ER, 0x00000000);	/* disable all */
	mtdcr(UIC2CR, 0x00000000);	/* all non-critical */
	mtdcr(UIC2PR, 0xffffc0ff);	/* per ref-board manual */
	mtdcr(UIC2TR, 0x00ff8000);	/* per ref-board manual */
	mtdcr(UIC2VR, 0x00000001);	/* int31 highest, base=0x000 */
	mtdcr(UIC2SR, 0xffffffff);	/* clear all */

	mtdcr(UIC3SR, 0xffffffff);	/* clear all */
	mtdcr(UIC3ER, 0x00000000);	/* disable all */
	mtdcr(UIC3CR, 0x00000000);	/* all non-critical */
	mtdcr(UIC3PR, 0xffffffff);	/* per ref-board manual */
	mtdcr(UIC3TR, 0x00ff8c0f);	/* per ref-board manual */
	mtdcr(UIC3VR, 0x00000001);	/* int31 highest, base=0x000 */
	mtdcr(UIC3SR, 0xffffffff);	/* clear all */

	mtdcr(UIC0SR, 0xfc000000);	/* clear all */
	mtdcr(UIC0ER, 0x00000000);	/* disable all */
	mtdcr(UIC0CR, 0x00000000);	/* all non-critical */
	mtdcr(UIC0PR, 0xfc000000);	/* */
	mtdcr(UIC0TR, 0x00000000);	/* */
	mtdcr(UIC0VR, 0x00000001);	/* */

	LED0_ON();

	return 0;
}

int checkboard(void)
{
	char buf[64];
	int i;

	printf("Board: X-ES %s PMC SBC\n", CONFIG_SYS_BOARD_NAME);
	printf("       ");
	i = getenv_f("board_rev", buf, sizeof(buf));
	if (i > 0)
		printf("Rev %s, ", buf);
	i = getenv_f("serial#", buf, sizeof(buf));
	if (i > 0)
		printf("Serial# %s, ", buf);
	i = getenv_f("board_cfg", buf, sizeof(buf));
	if (i > 0)
		printf("Cfg %s", buf);
	printf("\n");

	return 0;
}

int dram_init(void)
{
	gd->ram_size = spd_sdram();

	return 0;
}

/*
 * Override weak pci_pre_init()
 *
 * This routine is called just prior to registering the hose and gives
 * the board the opportunity to check things. Returning a value of zero
 * indicates that things are bad & PCI initialization should be aborted.
 *
 * Different boards may wish to customize the pci controller structure
 * (add regions, override default access routines, etc) or perform
 * certain pre-initialization actions.
 */
#if defined(CONFIG_PCI)
int pci_pre_init(struct pci_controller * hose)
{
	unsigned long strap;

	/* See if we're supposed to setup the pci */
	mfsdr(SDR0_SDSTP1, strap);
	if ((strap & 0x00010000) == 0)
		return 0;

#if defined(CONFIG_SYS_PCI_FORCE_PCI_CONV)
	/* Setup System Device Register PCIL0_XCR */
	mfsdr(SDR0_XCR, strap);
	strap &= 0x0f000000;
	mtsdr(SDR0_XCR, strap);
#endif

	return 1;
}
#endif /* defined(CONFIG_PCI) */

#if defined(CONFIG_PCI)
/*
 * Override weak is_pci_host()
 *
 * This routine is called to determine if a pci scan should be
 * performed. With various hardware environments (especially cPCI and
 * PPMC) it's insufficient to depend on the state of the arbiter enable
 * bit in the strap register, or generic host/adapter assumptions.
 *
 * Rather than hard-code a bad assumption in the general 440 code, the
 * 440 pci code requires the board to decide at runtime.
 *
 * Return 0 for adapter mode, non-zero for host (monarch) mode.
 */
int is_pci_host(struct pci_controller *hose)
{
	return ((in32(CONFIG_SYS_GPIO_BASE + 0x1C) & 0x00000800) == 0);
}
#endif /* defined(CONFIG_PCI) */

#ifdef CONFIG_POST
/*
 * Returns 1 if keys pressed to start the power-on long-running tests
 * Called from board_init_f().
 */
int post_hotkeys_pressed(void)
{
	return ctrlc();
}
#endif