blob: 9a74064c98b5d13bb73cda2bb1a46f3aaf0cd643 [file] [log] [blame]
Masahiro Yamada4b0abf92014-10-03 19:21:03 +09001menu "NAND Device Support"
2
Masahiro Yamada65e41452014-11-13 20:31:50 +09003config SYS_NAND_SELF_INIT
4 bool
5 help
6 This option, if enabled, provides more flexible and linux-like
7 NAND initialization process.
8
Masahiro Yamada4b0abf92014-10-03 19:21:03 +09009config NAND_DENALI
10 bool "Support Denali NAND controller"
Masahiro Yamada65e41452014-11-13 20:31:50 +090011 select SYS_NAND_SELF_INIT
Masahiro Yamada4b0abf92014-10-03 19:21:03 +090012 help
13 Enable support for the Denali NAND controller.
14
15config SYS_NAND_DENALI_64BIT
16 bool "Use 64-bit variant of Denali NAND controller"
17 depends on NAND_DENALI
18 help
19 The Denali NAND controller IP has some variations in terms of
20 the bus interface. The DMA setup sequence is completely differenct
21 between 32bit / 64bit AXI bus variants.
22
23 If your Denali NAND controller is the 64-bit variant, say Y.
24 Otherwise (32 bit), say N.
25
26config NAND_DENALI_SPARE_AREA_SKIP_BYTES
27 int "Number of bytes skipped in OOB area"
28 depends on NAND_DENALI
29 range 0 63
30 help
31 This option specifies the number of bytes to skip from the beginning
32 of OOB area before last ECC sector data starts. This is potentially
33 used to preserve the bad block marker in the OOB area.
34
Stefan Agner55191942015-05-08 19:07:11 +020035config NAND_VF610_NFC
36 bool "Support for Freescale NFC for VF610/MPC5125"
37 select SYS_NAND_SELF_INIT
38 help
39 Enables support for NAND Flash Controller on some Freescale
40 processors like the VF610, MPC5125, MCF54418 or Kinetis K70.
41 The driver supports a maximum 2k page size. The driver
42 currently does not support hardware ECC.
43
Stefan Agner080a71e2015-05-08 19:07:12 +020044choice
45 prompt "Hardware ECC strength"
46 depends on NAND_VF610_NFC
47 default SYS_NAND_VF610_NFC_45_ECC_BYTES
48 help
49 Select the ECC strength used in the hardware BCH ECC block.
50
51config SYS_NAND_VF610_NFC_45_ECC_BYTES
52 bool "24-error correction (45 ECC bytes)"
53
54config SYS_NAND_VF610_NFC_60_ECC_BYTES
55 bool "32-error correction (60 ECC bytes)"
56
57endchoice
58
Stefan Roese873960c2015-07-23 10:26:16 +020059config NAND_PXA3XX
60 bool "Support for NAND on PXA3xx and Armada 370/XP/38x"
61 select SYS_NAND_SELF_INIT
62 help
63 This enables the driver for the NAND flash device found on
64 PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2).
65
Hans de Goedee5268612015-08-16 14:48:22 +020066config NAND_SUNXI
67 bool "Support for NAND on Allwinner SoCs in SPL"
68 depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
69 select SYS_NAND_SELF_INIT
70 ---help---
71 Enable support for NAND. This option allows SPL to read from
72 sunxi NAND using DMA transfers.
73
Stefan Agner55191942015-05-08 19:07:11 +020074comment "Generic NAND options"
75
76# Enhance depends when converting drivers to Kconfig which use this config
77# option (mxc_nand, ndfc, omap_gpmc).
78config SYS_NAND_BUSWIDTH_16BIT
79 bool "Use 16-bit NAND interface"
80 depends on NAND_VF610_NFC
81 help
82 Indicates that NAND device has 16-bit wide data-bus. In absence of this
83 config, bus-width of NAND device is assumed to be either 8-bit and later
84 determined by reading ONFI params.
85 Above config is useful when NAND device's bus-width information cannot
86 be determined from on-chip ONFI params, like in following scenarios:
87 - SPL boot does not support reading of ONFI parameters. This is done to
88 keep SPL code foot-print small.
89 - In current U-Boot flow using nand_init(), driver initialization
90 happens in board_nand_init() which is called before any device probe
91 (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are
92 not available while configuring controller. So a static CONFIG_NAND_xx
93 is needed to know the device's bus-width in advance.
94
Hans de Goeded90ba792015-08-21 21:49:51 +020095# Enhance depends when converting drivers to Kconfig which use this config
96config SYS_NAND_U_BOOT_OFFS
97 hex "Location in NAND to read U-Boot from"
98 default 0x8000 if NAND_SUNXI
99 depends on NAND_SUNXI
100 help
101 Set the offset from the start of the nand where u-boot should be
102 loaded from.
103
Masahiro Yamadae02ee252015-02-24 22:26:20 +0900104if SPL
Masahiro Yamada845034e2014-10-03 19:21:04 +0900105
106config SPL_NAND_DENALI
107 bool "Support Denali NAND controller for SPL"
108 help
109 This is a small implementation of the Denali NAND controller
110 for use on SPL.
111
112endif
113
Masahiro Yamada4b0abf92014-10-03 19:21:03 +0900114endmenu