board/freescale/mpc837xemds/mpc837xemds.c

/*
 * Copyright (C) 2007 Freescale Semiconductor, Inc.
 * Dave Liu <daveliu@freescale.com>
 *
 * CREDITS: Kim Phillips contribute to LIBFDT code
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 */

#include <common.h>
#include <i2c.h>
#include <asm/io.h>
#include <asm/fsl_serdes.h>
#include <spd_sdram.h>
#include <tsec.h>
#if defined(CONFIG_OF_LIBFDT)
#include <libfdt.h>
#endif
#if defined(CONFIG_PQ_MDS_PIB)
#include "../common/pq-mds-pib.h"
#endif

int board_early_init_f(void)
{
	u8 *bcsr = (u8 *)CONFIG_SYS_BCSR;

	/* Enable flash write */
	bcsr[0x9] &= ~0x04;
	/* Clear all of the interrupt of BCSR */
	bcsr[0xe] = 0xff;

#ifdef CONFIG_FSL_SERDES
	immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
	u32 spridr = in_be32(&immr->sysconf.spridr);

	/* we check only part num, and don't look for CPU revisions */
	switch (PARTID_NO_E(spridr)) {
	case SPR_8377:
		fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SATA,
				 FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
		fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_PEX,
				 FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
		break;
	case SPR_8378:
		fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SGMII,
				 FSL_SERDES_CLK_125, FSL_SERDES_VDD_1V);
		fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_PEX,
				 FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
		break;
	case SPR_8379:
		fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SATA,
				 FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
		fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_SATA,
				 FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
		break;
	default:
		printf("serdes not configured: unknown CPU part number: "
		       "%04x\n", spridr >> 16);
		break;
	}
#endif /* CONFIG_FSL_SERDES */
	return 0;
}

#if defined(CONFIG_TSEC1) || defined(CONFIG_TSEC2)
int board_eth_init(bd_t *bd)
{
	struct tsec_info_struct tsec_info[2];
	struct immap __iomem *im = (struct immap __iomem *)CONFIG_SYS_IMMR;
	u32 rcwh = in_be32(&im->reset.rcwh);
	u32 tsec_mode;
	int num = 0;

	/* New line after Net: */
	printf("\n");

#ifdef CONFIG_TSEC1
	SET_STD_TSEC_INFO(tsec_info[num], 1);

	printf(CONFIG_TSEC1_NAME ": ");

	tsec_mode = rcwh & HRCWH_TSEC1M_MASK;
	if (tsec_mode == HRCWH_TSEC1M_IN_RGMII) {
		printf("RGMII\n");
		/* this is default, no need to fixup */
	} else if (tsec_mode == HRCWH_TSEC1M_IN_SGMII) {
		printf("SGMII\n");
		tsec_info[num].phyaddr = TSEC1_PHY_ADDR_SGMII;
		tsec_info[num].flags = TSEC_GIGABIT;
	} else {
		printf("unsupported PHY type\n");
	}
	num++;
#endif
#ifdef CONFIG_TSEC2
	SET_STD_TSEC_INFO(tsec_info[num], 2);

	printf(CONFIG_TSEC2_NAME ": ");

	tsec_mode = rcwh & HRCWH_TSEC2M_MASK;
	if (tsec_mode == HRCWH_TSEC2M_IN_RGMII) {
		printf("RGMII\n");
		/* this is default, no need to fixup */
	} else if (tsec_mode == HRCWH_TSEC2M_IN_SGMII) {
		printf("SGMII\n");
		tsec_info[num].phyaddr = TSEC2_PHY_ADDR_SGMII;
		tsec_info[num].flags = TSEC_GIGABIT;
	} else {
		printf("unsupported PHY type\n");
	}
	num++;
#endif
	return tsec_eth_init(bd, tsec_info, num);
}

static void __ft_tsec_fixup(void *blob, bd_t *bd, const char *alias,
			    int phy_addr)
{
	const char *phy_type = "sgmii";
	const u32 *ph;
	int off;
	int err;

	off = fdt_path_offset(blob, alias);
	if (off < 0) {
		printf("WARNING: could not find %s alias: %s.\n", alias,
			fdt_strerror(off));
		return;
	}

	err = fdt_setprop(blob, off, "phy-connection-type", phy_type,
			  strlen(phy_type) + 1);
	if (err) {
		printf("WARNING: could not set phy-connection-type for %s: "
			"%s.\n", alias, fdt_strerror(err));
		return;
	}

	ph = (u32 *)fdt_getprop(blob, off, "phy-handle", 0);
	if (!ph) {
		printf("WARNING: could not get phy-handle for %s.\n",
			alias);
		return;
	}

	off = fdt_node_offset_by_phandle(blob, *ph);
	if (off < 0) {
		printf("WARNING: could not get phy node for %s: %s\n", alias,
			fdt_strerror(off));
		return;
	}

	phy_addr = cpu_to_fdt32(phy_addr);
	err = fdt_setprop(blob, off, "reg", &phy_addr, sizeof(phy_addr));
	if (err < 0) {
		printf("WARNING: could not set phy node's reg for %s: "
			"%s.\n", alias, fdt_strerror(err));
		return;
	}
}

static void ft_tsec_fixup(void *blob, bd_t *bd)
{
	struct immap __iomem *im = (struct immap __iomem *)CONFIG_SYS_IMMR;
	u32 rcwh = in_be32(&im->reset.rcwh);
	u32 tsec_mode;

#ifdef CONFIG_TSEC1
	tsec_mode = rcwh & HRCWH_TSEC1M_MASK;
	if (tsec_mode == HRCWH_TSEC1M_IN_SGMII)
		__ft_tsec_fixup(blob, bd, "ethernet0", TSEC1_PHY_ADDR_SGMII);
#endif

#ifdef CONFIG_TSEC2
	tsec_mode = rcwh & HRCWH_TSEC2M_MASK;
	if (tsec_mode == HRCWH_TSEC2M_IN_SGMII)
		__ft_tsec_fixup(blob, bd, "ethernet1", TSEC2_PHY_ADDR_SGMII);
#endif
}
#else
static inline void ft_tsec_fixup(void *blob, bd_t *bd) {}
#endif /* defined(CONFIG_TSEC1) || defined(CONFIG_TSEC2) */

int board_early_init_r(void)
{
#ifdef CONFIG_PQ_MDS_PIB
	pib_init();
#endif
	return 0;
}

#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC)
extern void ddr_enable_ecc(unsigned int dram_size);
#endif
int fixed_sdram(void);

phys_size_t initdram(int board_type)
{
	volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
	u32 msize = 0;

	if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32) im)
		return -1;

#if defined(CONFIG_SPD_EEPROM)
	msize = spd_sdram();
#else
	msize = fixed_sdram();
#endif

#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC)
	/* Initialize DDR ECC byte */
	ddr_enable_ecc(msize * 1024 * 1024);
#endif

	/* return total bus DDR size(bytes) */
	return (msize * 1024 * 1024);
}

#if !defined(CONFIG_SPD_EEPROM)
/*************************************************************************
 *  fixed sdram init -- doesn't use serial presence detect.
 ************************************************************************/
int fixed_sdram(void)
{
	volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
	u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024;
	u32 msize_log2 = __ilog2(msize);

	im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000;
	im->sysconf.ddrlaw[0].ar = LBLAWAR_EN | (msize_log2 - 1);

#if (CONFIG_SYS_DDR_SIZE != 512)
#warning Currenly any ddr size other than 512 is not supported
#endif
	im->sysconf.ddrcdr = CONFIG_SYS_DDRCDR_VALUE;
	udelay(50000);

	im->ddr.sdram_clk_cntl = CONFIG_SYS_DDR_SDRAM_CLK_CNTL;
	udelay(1000);

	im->ddr.csbnds[0].csbnds = CONFIG_SYS_DDR_CS0_BNDS;
	im->ddr.cs_config[0] = CONFIG_SYS_DDR_CS0_CONFIG;
	udelay(1000);

	im->ddr.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0;
	im->ddr.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
	im->ddr.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
	im->ddr.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3;
	im->ddr.sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG;
	im->ddr.sdram_cfg2 = CONFIG_SYS_DDR_SDRAM_CFG2;
	im->ddr.sdram_mode = CONFIG_SYS_DDR_MODE;
	im->ddr.sdram_mode2 = CONFIG_SYS_DDR_MODE2;
	im->ddr.sdram_interval = CONFIG_SYS_DDR_INTERVAL;
	__asm__ __volatile__("sync");
	udelay(1000);

	im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
	udelay(2000);
	return CONFIG_SYS_DDR_SIZE;
}
#endif /*!CONFIG_SYS_SPD_EEPROM */

int checkboard(void)
{
	puts("Board: Freescale MPC837xEMDS\n");
	return 0;
}

#ifdef CONFIG_PCI
int board_pci_host_broken(void)
{
	struct immap __iomem *im = (struct immap __iomem *)CONFIG_SYS_IMMR;
	const u32 rcw_mask = HRCWH_PCI1_ARBITER_ENABLE | HRCWH_PCI_HOST;
	const char *pci_ea = getenv("pci_external_arbiter");

	/* It's always OK in case of external arbiter. */
	if (pci_ea && !strcmp(pci_ea, "yes"))
		return 0;

	if ((in_be32(&im->reset.rcwh) & rcw_mask) != rcw_mask)
		return 1;

	return 0;
}

static void ft_pci_fixup(void *blob, bd_t *bd)
{
	const char *status = "broken (no arbiter)";
	int off;
	int err;

	off = fdt_path_offset(blob, "pci0");
	if (off < 0) {
		printf("WARNING: could not find pci0 alias: %s.\n",
			fdt_strerror(off));
		return;
	}

	err = fdt_setprop(blob, off, "status", status, strlen(status) + 1);
	if (err) {
		printf("WARNING: could not set status for pci0: %s.\n",
			fdt_strerror(err));
		return;
	}
}
#endif

#if defined(CONFIG_OF_BOARD_SETUP)
void ft_board_setup(void *blob, bd_t *bd)
{
	ft_cpu_setup(blob, bd);
	ft_tsec_fixup(blob, bd);
#ifdef CONFIG_PCI
	ft_pci_setup(blob, bd);
	if (board_pci_host_broken())
		ft_pci_fixup(blob, bd);
#endif
}
#endif /* CONFIG_OF_BOARD_SETUP */