blob: 7c7690ff555be6f0319d18ec4c7347fcf38eddff [file] [log] [blame]
wdenk7d393ae2002-10-25 21:08:05 +00001/*
2 * (C) Copyright 2001
3 * Denis Peter, MPL AG Switzerland, d.peter@mpl.ch
4 *
Wolfgang Denk1a459662013-07-08 09:37:19 +02005 * SPDX-License-Identifier: GPL-2.0+
wdenk7d393ae2002-10-25 21:08:05 +00006 *
7 * TODO: clean-up
8 */
9
10#include <common.h>
11#include "pip405.h"
12#include <asm/processor.h>
13#include <i2c.h>
Jean-Christophe PLAGNIOL-VILLARD28c34502009-05-16 12:14:56 +020014#include <stdio_dev.h>
wdenk7d393ae2002-10-25 21:08:05 +000015#include "../common/isa.h"
16#include "../common/common_util.h"
17
Wolfgang Denkd87080b2006-03-31 18:32:53 +020018DECLARE_GLOBAL_DATA_PTR;
19
wdenk7d393ae2002-10-25 21:08:05 +000020#undef SDRAM_DEBUG
21
wdenk7d393ae2002-10-25 21:08:05 +000022/* stdlib.h causes some compatibility problems; should fixe these! -- wd */
23#ifndef __ldiv_t_defined
24typedef struct {
25 long int quot; /* Quotient */
26 long int rem; /* Remainder */
27} ldiv_t;
28extern ldiv_t ldiv (long int __numer, long int __denom);
29
30# define __ldiv_t_defined 1
31#endif
32
33
34typedef enum {
35 SDRAM_NO_ERR,
36 SDRAM_SPD_COMM_ERR,
37 SDRAM_SPD_CHKSUM_ERR,
38 SDRAM_UNSUPPORTED_ERR,
39 SDRAM_UNKNOWN_ERR
40} SDRAM_ERR;
41
42typedef struct {
43 const unsigned char mode;
44 const unsigned char row;
45 const unsigned char col;
46 const unsigned char bank;
47} SDRAM_SETUP;
48
49static const SDRAM_SETUP sdram_setup_table[] = {
50 {1, 11, 9, 2},
51 {1, 11, 10, 2},
52 {2, 12, 9, 4},
53 {2, 12, 10, 4},
54 {3, 13, 9, 4},
55 {3, 13, 10, 4},
56 {3, 13, 11, 4},
57 {4, 12, 8, 2},
58 {4, 12, 8, 4},
59 {5, 11, 8, 2},
60 {5, 11, 8, 4},
61 {6, 13, 8, 2},
62 {6, 13, 8, 4},
63 {7, 13, 9, 2},
64 {7, 13, 10, 2},
65 {0, 0, 0, 0}
66};
67
68static const unsigned char cal_indextable[] = {
69 9, 23, 25
70};
71
72
73/*
74 * translate ns.ns/10 coding of SPD timing values
75 * into 10 ps unit values
76 */
77
78unsigned short NS10to10PS (unsigned char spd_byte, unsigned char spd_version)
79{
80 unsigned short ns, ns10;
81
82 /* isolate upper nibble */
83 ns = (spd_byte >> 4) & 0x0F;
84 /* isolate lower nibble */
85 ns10 = (spd_byte & 0x0F);
86
87 return (ns * 100 + ns10 * 10);
88}
89
90/*
91 * translate ns.ns/4 coding of SPD timing values
92 * into 10 ps unit values
93 */
94
95unsigned short NS4to10PS (unsigned char spd_byte, unsigned char spd_version)
96{
97 unsigned short ns, ns4;
98
99 /* isolate upper 6 bits */
100 ns = (spd_byte >> 2) & 0x3F;
101 /* isloate lower 2 bits */
102 ns4 = (spd_byte & 0x03);
103
104 return (ns * 100 + ns4 * 25);
105}
106
107/*
108 * translate ns coding of SPD timing values
109 * into 10 ps unit values
110 */
111
112unsigned short NSto10PS (unsigned char spd_byte)
113{
114 return (spd_byte * 100);
115}
116
117void SDRAM_err (const char *s)
118{
119#ifndef SDRAM_DEBUG
wdenk7d393ae2002-10-25 21:08:05 +0000120 (void) get_clocks ();
121 gd->baudrate = 9600;
122 serial_init ();
123#endif
124 serial_puts ("\n");
125 serial_puts (s);
126 serial_puts ("\n enable SDRAM_DEBUG for more info\n");
127 for (;;);
128}
129
130
131#ifdef SDRAM_DEBUG
132
133void write_hex (unsigned char i)
134{
135 char cc;
136
137 cc = i >> 4;
138 cc &= 0xf;
139 if (cc > 9)
140 serial_putc (cc + 55);
141 else
142 serial_putc (cc + 48);
143 cc = i & 0xf;
144 if (cc > 9)
145 serial_putc (cc + 55);
146 else
147 serial_putc (cc + 48);
148}
149
150void write_4hex (unsigned long val)
151{
152 write_hex ((unsigned char) (val >> 24));
153 write_hex ((unsigned char) (val >> 16));
154 write_hex ((unsigned char) (val >> 8));
155 write_hex ((unsigned char) val);
156}
157
158#endif
159
wdenkc837dcb2004-01-20 23:12:12 +0000160int board_early_init_f (void)
wdenk7d393ae2002-10-25 21:08:05 +0000161{
wdenk7d393ae2002-10-25 21:08:05 +0000162 unsigned char datain[128];
Wolfgang Denk77ddac92005-10-13 16:45:02 +0200163 unsigned long sdram_size = 0;
wdenk7d393ae2002-10-25 21:08:05 +0000164 SDRAM_SETUP *t = (SDRAM_SETUP *) sdram_setup_table;
165 unsigned long memclk;
166 unsigned long tmemclk = 0;
167 unsigned long tmp, bank, baseaddr, bank_size;
168 unsigned short i;
169 unsigned char rows, cols, banks, sdram_banks, density;
170 unsigned char supported_cal, trp_clocks, trcd_clocks, tras_clocks,
Stefan Roese4e11c352011-11-15 08:03:45 +0000171 trc_clocks;
wdenk7d393ae2002-10-25 21:08:05 +0000172 unsigned char cal_index, cal_val, spd_version, spd_chksum;
173 unsigned char buf[8];
Stefan Roese4e11c352011-11-15 08:03:45 +0000174#ifdef SDRAM_DEBUG
175 unsigned char tctp_clocks;
176#endif
177
wdenk7205e402003-09-10 22:30:53 +0000178 /* set up the config port */
Stefan Roesed1c3b272009-09-09 16:25:29 +0200179 mtdcr (EBC0_CFGADDR, PB7AP);
180 mtdcr (EBC0_CFGDATA, CONFIG_PORT_AP);
181 mtdcr (EBC0_CFGADDR, PB7CR);
182 mtdcr (EBC0_CFGDATA, CONFIG_PORT_CR);
wdenk7d393ae2002-10-25 21:08:05 +0000183
184 memclk = get_bus_freq (tmemclk);
185 tmemclk = 1000000000 / (memclk / 100); /* in 10 ps units */
186
187#ifdef SDRAM_DEBUG
188 (void) get_clocks ();
189 gd->baudrate = 9600;
190 serial_init ();
191 serial_puts ("\nstart SDRAM Setup\n");
192#endif
193
194 /* Read Serial Presence Detect Information */
Dirk Eibach880540d2013-04-25 02:40:01 +0000195 i2c_set_bus_num(0);
wdenk7d393ae2002-10-25 21:08:05 +0000196 for (i = 0; i < 128; i++)
197 datain[i] = 127;
198 i2c_read(SPD_EEPROM_ADDRESS,0,1,datain,128);
199#ifdef SDRAM_DEBUG
200 serial_puts ("\ni2c_read returns ");
201 write_hex (i);
202 serial_puts ("\n");
203#endif
204
205#ifdef SDRAM_DEBUG
206 for (i = 0; i < 128; i++) {
207 write_hex (datain[i]);
208 serial_puts (" ");
209 if (((i + 1) % 16) == 0)
210 serial_puts ("\n");
211 }
212 serial_puts ("\n");
213#endif
214 spd_chksum = 0;
215 for (i = 0; i < 63; i++) {
216 spd_chksum += datain[i];
217 } /* endfor */
218 if (datain[63] != spd_chksum) {
219#ifdef SDRAM_DEBUG
220 serial_puts ("SPD chksum: 0x");
221 write_hex (datain[63]);
222 serial_puts (" != calc. chksum: 0x");
223 write_hex (spd_chksum);
224 serial_puts ("\n");
225#endif
226 SDRAM_err ("SPD checksum Error");
227 }
228 /* SPD seems to be ok, use it */
229
230 /* get SPD version */
231 spd_version = datain[62];
232
233 /* do some sanity checks on the kind of RAM */
234 if ((datain[0] < 0x80) || /* less than 128 valid bytes in SPD */
235 (datain[2] != 0x04) || /* if not SDRAM */
236 (!((datain[6] == 0x40) || (datain[6] == 0x48))) || /* or not (64 Bit or 72 Bit) */
237 (datain[7] != 0x00) || (datain[8] != 0x01) || /* or not LVTTL signal levels */
Wolfgang Denk8ed44d92008-10-19 02:35:50 +0200238 (datain[126] == 0x66)) /* or a 66MHz modules */
wdenk7d393ae2002-10-25 21:08:05 +0000239 SDRAM_err ("unsupported SDRAM");
240#ifdef SDRAM_DEBUG
241 serial_puts ("SDRAM sanity ok\n");
242#endif
243
244 /* get number of rows/cols/banks out of byte 3+4+5 */
245 rows = datain[3];
246 cols = datain[4];
247 banks = datain[5];
248
249 /* get number of SDRAM banks out of byte 17 and
250 supported CAS latencies out of byte 18 */
251 sdram_banks = datain[17];
252 supported_cal = datain[18] & ~0x81;
253
254 while (t->mode != 0) {
255 if ((t->row == rows) && (t->col == cols)
256 && (t->bank == sdram_banks))
257 break;
258 t++;
259 } /* endwhile */
260
261#ifdef SDRAM_DEBUG
262 serial_puts ("rows: ");
263 write_hex (rows);
264 serial_puts (" cols: ");
265 write_hex (cols);
266 serial_puts (" banks: ");
267 write_hex (banks);
268 serial_puts (" mode: ");
269 write_hex (t->mode);
270 serial_puts ("\n");
271#endif
272 if (t->mode == 0)
273 SDRAM_err ("unsupported SDRAM");
274 /* get tRP, tRCD, tRAS and density from byte 27+29+30+31 */
275#ifdef SDRAM_DEBUG
276 serial_puts ("tRP: ");
277 write_hex (datain[27]);
278 serial_puts ("\ntRCD: ");
279 write_hex (datain[29]);
280 serial_puts ("\ntRAS: ");
281 write_hex (datain[30]);
282 serial_puts ("\n");
283#endif
284
285 trp_clocks = (NSto10PS (datain[27]) + (tmemclk - 1)) / tmemclk;
286 trcd_clocks = (NSto10PS (datain[29]) + (tmemclk - 1)) / tmemclk;
287 tras_clocks = (NSto10PS (datain[30]) + (tmemclk - 1)) / tmemclk;
288 density = datain[31];
289
290 /* trc_clocks is sum of trp_clocks + tras_clocks */
291 trc_clocks = trp_clocks + tras_clocks;
Stefan Roese4e11c352011-11-15 08:03:45 +0000292
293#ifdef SDRAM_DEBUG
wdenk7d393ae2002-10-25 21:08:05 +0000294 /* ctp = ((trp + tras) - trp - trcd) => tras - trcd */
295 tctp_clocks =
296 ((NSto10PS (datain[30]) - NSto10PS (datain[29])) +
297 (tmemclk - 1)) / tmemclk;
298
wdenk7d393ae2002-10-25 21:08:05 +0000299 serial_puts ("c_RP: ");
300 write_hex (trp_clocks);
301 serial_puts ("\nc_RCD: ");
302 write_hex (trcd_clocks);
303 serial_puts ("\nc_RAS: ");
304 write_hex (tras_clocks);
305 serial_puts ("\nc_RC: (RP+RAS): ");
306 write_hex (trc_clocks);
307 serial_puts ("\nc_CTP: ((RP+RAS)-RP-RCD): ");
308 write_hex (tctp_clocks);
309 serial_puts ("\nt_CTP: RAS - RCD: ");
310 write_hex ((unsigned
311 char) ((NSto10PS (datain[30]) -
312 NSto10PS (datain[29])) >> 8));
313 write_hex ((unsigned char) (NSto10PS (datain[30]) - NSto10PS (datain[29])));
314 serial_puts ("\ntmemclk: ");
315 write_hex ((unsigned char) (tmemclk >> 8));
316 write_hex ((unsigned char) (tmemclk));
317 serial_puts ("\n");
318#endif
319
320
321 cal_val = 255;
322 for (i = 6, cal_index = 0; (i > 0) && (cal_index < 3); i--) {
323 /* is this CAS latency supported ? */
324 if ((supported_cal >> i) & 0x01) {
325 buf[0] = datain[cal_indextable[cal_index]];
326 if (cal_index < 2) {
327 if (NS10to10PS (buf[0], spd_version) <= tmemclk)
328 cal_val = i;
329 } else {
330 /* SPD bytes 25+26 have another format */
331 if (NS4to10PS (buf[0], spd_version) <= tmemclk)
332 cal_val = i;
333 } /* endif */
334 cal_index++;
335 } /* endif */
336 } /* endfor */
337#ifdef SDRAM_DEBUG
338 serial_puts ("CAL: ");
339 write_hex (cal_val + 1);
340 serial_puts ("\n");
341#endif
342
343 if (cal_val == 255)
344 SDRAM_err ("unsupported SDRAM");
345
346 /* get SDRAM timing register */
Stefan Roese95b602b2009-09-24 13:59:57 +0200347 mtdcr (SDRAM0_CFGADDR, SDRAM0_TR);
Stefan Roesed1c3b272009-09-09 16:25:29 +0200348 tmp = mfdcr (SDRAM0_CFGDATA) & ~0x018FC01F;
wdenk7d393ae2002-10-25 21:08:05 +0000349 /* insert CASL value */
350/* tmp |= ((unsigned long)cal_val) << 23; */
351 tmp |= ((unsigned long) cal_val) << 23;
352 /* insert PTA value */
353 tmp |= ((unsigned long) (trp_clocks - 1)) << 18;
354 /* insert CTP value */
355/* tmp |= ((unsigned long)(trc_clocks - trp_clocks - trcd_clocks - 1)) << 16; */
356 tmp |= ((unsigned long) (trc_clocks - trp_clocks - trcd_clocks)) << 16;
357 /* insert LDF (always 01) */
358 tmp |= ((unsigned long) 0x01) << 14;
359 /* insert RFTA value */
360 tmp |= ((unsigned long) (trc_clocks - 4)) << 2;
361 /* insert RCD value */
362 tmp |= ((unsigned long) (trcd_clocks - 1)) << 0;
363
364#ifdef SDRAM_DEBUG
365 serial_puts ("sdtr: ");
366 write_4hex (tmp);
367 serial_puts ("\n");
368#endif
369
370 /* write SDRAM timing register */
Stefan Roese95b602b2009-09-24 13:59:57 +0200371 mtdcr (SDRAM0_CFGADDR, SDRAM0_TR);
Stefan Roesed1c3b272009-09-09 16:25:29 +0200372 mtdcr (SDRAM0_CFGDATA, tmp);
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200373 baseaddr = CONFIG_SYS_SDRAM_BASE;
wdenk7d393ae2002-10-25 21:08:05 +0000374 bank_size = (((unsigned long) density) << 22) / 2;
375 /* insert AM value */
376 tmp = ((unsigned long) t->mode - 1) << 13;
377 /* insert SZ value; */
378 switch (bank_size) {
379 case 0x00400000:
380 tmp |= ((unsigned long) 0x00) << 17;
381 break;
382 case 0x00800000:
383 tmp |= ((unsigned long) 0x01) << 17;
384 break;
385 case 0x01000000:
386 tmp |= ((unsigned long) 0x02) << 17;
387 break;
388 case 0x02000000:
389 tmp |= ((unsigned long) 0x03) << 17;
390 break;
391 case 0x04000000:
392 tmp |= ((unsigned long) 0x04) << 17;
393 break;
394 case 0x08000000:
395 tmp |= ((unsigned long) 0x05) << 17;
396 break;
397 case 0x10000000:
398 tmp |= ((unsigned long) 0x06) << 17;
399 break;
400 default:
401 SDRAM_err ("unsupported SDRAM");
402 } /* endswitch */
403 /* get SDRAM bank 0 register */
Stefan Roese95b602b2009-09-24 13:59:57 +0200404 mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
Stefan Roesed1c3b272009-09-09 16:25:29 +0200405 bank = mfdcr (SDRAM0_CFGDATA) & ~0xFFCEE001;
wdenk7d393ae2002-10-25 21:08:05 +0000406 bank |= (baseaddr | tmp | 0x01);
407#ifdef SDRAM_DEBUG
408 serial_puts ("bank0: baseaddr: ");
409 write_4hex (baseaddr);
410 serial_puts (" banksize: ");
411 write_4hex (bank_size);
412 serial_puts (" mb0cf: ");
413 write_4hex (bank);
414 serial_puts ("\n");
415#endif
416 baseaddr += bank_size;
417 sdram_size += bank_size;
418
419 /* write SDRAM bank 0 register */
Stefan Roese95b602b2009-09-24 13:59:57 +0200420 mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
Stefan Roesed1c3b272009-09-09 16:25:29 +0200421 mtdcr (SDRAM0_CFGDATA, bank);
wdenk7d393ae2002-10-25 21:08:05 +0000422
423 /* get SDRAM bank 1 register */
Stefan Roese95b602b2009-09-24 13:59:57 +0200424 mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR);
Stefan Roesed1c3b272009-09-09 16:25:29 +0200425 bank = mfdcr (SDRAM0_CFGDATA) & ~0xFFCEE001;
wdenk7d393ae2002-10-25 21:08:05 +0000426 sdram_size = 0;
427
428#ifdef SDRAM_DEBUG
429 serial_puts ("bank1: baseaddr: ");
430 write_4hex (baseaddr);
431 serial_puts (" banksize: ");
432 write_4hex (bank_size);
433#endif
434 if (banks == 2) {
435 bank |= (baseaddr | tmp | 0x01);
436 baseaddr += bank_size;
437 sdram_size += bank_size;
438 } /* endif */
439#ifdef SDRAM_DEBUG
440 serial_puts (" mb1cf: ");
441 write_4hex (bank);
442 serial_puts ("\n");
443#endif
444 /* write SDRAM bank 1 register */
Stefan Roese95b602b2009-09-24 13:59:57 +0200445 mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR);
Stefan Roesed1c3b272009-09-09 16:25:29 +0200446 mtdcr (SDRAM0_CFGDATA, bank);
wdenk7d393ae2002-10-25 21:08:05 +0000447
448 /* get SDRAM bank 2 register */
Stefan Roese95b602b2009-09-24 13:59:57 +0200449 mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR);
Stefan Roesed1c3b272009-09-09 16:25:29 +0200450 bank = mfdcr (SDRAM0_CFGDATA) & ~0xFFCEE001;
wdenk7d393ae2002-10-25 21:08:05 +0000451
452 bank |= (baseaddr | tmp | 0x01);
453
454#ifdef SDRAM_DEBUG
455 serial_puts ("bank2: baseaddr: ");
456 write_4hex (baseaddr);
457 serial_puts (" banksize: ");
458 write_4hex (bank_size);
459 serial_puts (" mb2cf: ");
460 write_4hex (bank);
461 serial_puts ("\n");
462#endif
463
464 baseaddr += bank_size;
465 sdram_size += bank_size;
466
467 /* write SDRAM bank 2 register */
Stefan Roese95b602b2009-09-24 13:59:57 +0200468 mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR);
Stefan Roesed1c3b272009-09-09 16:25:29 +0200469 mtdcr (SDRAM0_CFGDATA, bank);
wdenk7d393ae2002-10-25 21:08:05 +0000470
471 /* get SDRAM bank 3 register */
Stefan Roese95b602b2009-09-24 13:59:57 +0200472 mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR);
Stefan Roesed1c3b272009-09-09 16:25:29 +0200473 bank = mfdcr (SDRAM0_CFGDATA) & ~0xFFCEE001;
wdenk7d393ae2002-10-25 21:08:05 +0000474
475#ifdef SDRAM_DEBUG
476 serial_puts ("bank3: baseaddr: ");
477 write_4hex (baseaddr);
478 serial_puts (" banksize: ");
479 write_4hex (bank_size);
480#endif
481
482 if (banks == 2) {
483 bank |= (baseaddr | tmp | 0x01);
484 baseaddr += bank_size;
485 sdram_size += bank_size;
486 }
487 /* endif */
488#ifdef SDRAM_DEBUG
489 serial_puts (" mb3cf: ");
490 write_4hex (bank);
491 serial_puts ("\n");
492#endif
493
494 /* write SDRAM bank 3 register */
Stefan Roese95b602b2009-09-24 13:59:57 +0200495 mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR);
Stefan Roesed1c3b272009-09-09 16:25:29 +0200496 mtdcr (SDRAM0_CFGDATA, bank);
wdenk7d393ae2002-10-25 21:08:05 +0000497
498
499 /* get SDRAM refresh interval register */
Stefan Roese95b602b2009-09-24 13:59:57 +0200500 mtdcr (SDRAM0_CFGADDR, SDRAM0_RTR);
Stefan Roesed1c3b272009-09-09 16:25:29 +0200501 tmp = mfdcr (SDRAM0_CFGDATA) & ~0x3FF80000;
wdenk7d393ae2002-10-25 21:08:05 +0000502
503 if (tmemclk < NSto10PS (16))
504 tmp |= 0x05F00000;
505 else
506 tmp |= 0x03F80000;
507
508 /* write SDRAM refresh interval register */
Stefan Roese95b602b2009-09-24 13:59:57 +0200509 mtdcr (SDRAM0_CFGADDR, SDRAM0_RTR);
Stefan Roesed1c3b272009-09-09 16:25:29 +0200510 mtdcr (SDRAM0_CFGDATA, tmp);
wdenk7d393ae2002-10-25 21:08:05 +0000511
512 /* enable SDRAM controller with no ECC, 32-bit SDRAM width, 16 byte burst */
Stefan Roese95b602b2009-09-24 13:59:57 +0200513 mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
Stefan Roesed1c3b272009-09-09 16:25:29 +0200514 tmp = (mfdcr (SDRAM0_CFGDATA) & ~0xFFE00000) | 0x80E00000;
Stefan Roese95b602b2009-09-24 13:59:57 +0200515 mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
Stefan Roesed1c3b272009-09-09 16:25:29 +0200516 mtdcr (SDRAM0_CFGDATA, tmp);
wdenk7d393ae2002-10-25 21:08:05 +0000517
518
wdenk7d393ae2002-10-25 21:08:05 +0000519 /*-------------------------------------------------------------------------+
520 | Interrupt controller setup for the PIP405 board.
521 | Note: IRQ 0-15 405GP internally generated; active high; level sensitive
522 | IRQ 16 405GP internally generated; active low; level sensitive
523 | IRQ 17-24 RESERVED
524 | IRQ 25 (EXT IRQ 0) SouthBridg; active low; level sensitive
525 | IRQ 26 (EXT IRQ 1) NMI: active low; level sensitive
526 | IRQ 27 (EXT IRQ 2) SMI: active Low; level sensitive
527 | IRQ 28 (EXT IRQ 3) PCI SLOT 3; active low; level sensitive
528 | IRQ 29 (EXT IRQ 4) PCI SLOT 2; active low; level sensitive
529 | IRQ 30 (EXT IRQ 5) PCI SLOT 1; active low; level sensitive
530 | IRQ 31 (EXT IRQ 6) PCI SLOT 0; active low; level sensitive
531 | Note for PIP405 board:
532 | An interrupt taken for the SouthBridge (IRQ 25) indicates that
533 | the Interrupt Controller in the South Bridge has caused the
534 | interrupt. The IC must be read to determine which device
535 | caused the interrupt.
536 |
537 +-------------------------------------------------------------------------*/
Stefan Roese952e7762009-09-24 09:55:50 +0200538 mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */
539 mtdcr (UIC0ER, 0x00000000); /* disable all ints */
540 mtdcr (UIC0CR, 0x00000000); /* set all to be non-critical (for now) */
541 mtdcr (UIC0PR, 0xFFFFFF80); /* set int polarities */
542 mtdcr (UIC0TR, 0x10000000); /* set int trigger levels */
543 mtdcr (UIC0VCR, 0x00000001); /* set vect base=0,INT0 highest priority */
544 mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */
wdenk7d393ae2002-10-25 21:08:05 +0000545
546 return 0;
547}
548
David Müller21be3092011-12-22 13:38:20 +0100549int board_early_init_r(void)
550{
551 int mode;
wdenk7d393ae2002-10-25 21:08:05 +0000552
David Müller21be3092011-12-22 13:38:20 +0100553 /*
554 * since we are relocated, we can finally enable i-cache
555 * and set up the flash CS correctly
556 */
557 icache_enable();
558 setup_cs_reloc();
559 /* get and display boot mode */
560 mode = get_boot_mode();
561 if (mode & BOOT_PCI)
562 printf("PCI Boot %s Map\n", (mode & BOOT_MPS) ?
563 "MPS" : "Flash");
564 else
565 printf("%s Boot\n", (mode & BOOT_MPS) ?
566 "MPS" : "Flash");
567
568 return 0;
569}
wdenk7d393ae2002-10-25 21:08:05 +0000570/* ------------------------------------------------------------------------- */
571
572/*
573 * Check Board Identity:
574 */
575
576int checkboard (void)
577{
Wolfgang Denk77ddac92005-10-13 16:45:02 +0200578 char s[50];
wdenk7d393ae2002-10-25 21:08:05 +0000579 unsigned char bc;
580 int i;
581 backup_t *b = (backup_t *) s;
582
583 puts ("Board: ");
584
Wolfgang Denkcdb74972010-07-24 21:55:43 +0200585 i = getenv_f("serial#", (char *)s, 32);
Wolfgang Denk77ddac92005-10-13 16:45:02 +0200586 if ((i == 0) || strncmp ((char *)s, "PIP405", 6)) {
wdenk7d393ae2002-10-25 21:08:05 +0000587 get_backup_values (b);
588 if (strncmp (b->signature, "MPL\0", 4) != 0) {
589 puts ("### No HW ID - assuming PIP405");
590 } else {
591 b->serial_name[6] = 0;
592 printf ("%s SN: %s", b->serial_name,
593 &b->serial_name[7]);
594 }
595 } else {
596 s[6] = 0;
597 printf ("%s SN: %s", s, &s[7]);
598 }
599 bc = in8 (CONFIG_PORT_ADDR);
600 printf (" Boot Config: 0x%x\n", bc);
601 return (0);
602}
603
604
605/* ------------------------------------------------------------------------- */
606/* ------------------------------------------------------------------------- */
607/*
608 initdram(int board_type) reads EEPROM via I2c. EEPROM contains all of
609 the necessary info for SDRAM controller configuration
610*/
611/* ------------------------------------------------------------------------- */
612/* ------------------------------------------------------------------------- */
613static int test_dram (unsigned long ramsize);
614
Becky Bruce9973e3c2008-06-09 16:03:40 -0500615phys_size_t initdram (int board_type)
wdenk7d393ae2002-10-25 21:08:05 +0000616{
wdenk7d393ae2002-10-25 21:08:05 +0000617 unsigned long bank_reg[4], tmp, bank_size;
618 int i, ds;
619 unsigned long TotalSize;
620
621 ds = 0;
622 /* since the DRAM controller is allready set up,
623 * calculate the size with the bank registers
624 */
Stefan Roese95b602b2009-09-24 13:59:57 +0200625 mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
Stefan Roesed1c3b272009-09-09 16:25:29 +0200626 bank_reg[0] = mfdcr (SDRAM0_CFGDATA);
Stefan Roese95b602b2009-09-24 13:59:57 +0200627 mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR);
Stefan Roesed1c3b272009-09-09 16:25:29 +0200628 bank_reg[1] = mfdcr (SDRAM0_CFGDATA);
Stefan Roese95b602b2009-09-24 13:59:57 +0200629 mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR);
Stefan Roesed1c3b272009-09-09 16:25:29 +0200630 bank_reg[2] = mfdcr (SDRAM0_CFGDATA);
Stefan Roese95b602b2009-09-24 13:59:57 +0200631 mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR);
Stefan Roesed1c3b272009-09-09 16:25:29 +0200632 bank_reg[3] = mfdcr (SDRAM0_CFGDATA);
wdenk7d393ae2002-10-25 21:08:05 +0000633 TotalSize = 0;
634 for (i = 0; i < 4; i++) {
635 if ((bank_reg[i] & 0x1) == 0x1) {
636 tmp = (bank_reg[i] >> 17) & 0x7;
637 bank_size = 4 << tmp;
638 TotalSize += bank_size;
639 } else
640 ds = 1;
641 }
642 if (ds == 1)
643 printf ("single-sided DIMM ");
644 else
645 printf ("double-sided DIMM ");
646 test_dram (TotalSize * 1024 * 1024);
647 /* bank 2 (SDRAM Clock 2) is not usable if 133MHz SDRAM IF */
648 (void) get_clocks();
649 if (gd->cpu_clk > 220000000)
650 TotalSize /= 2;
651 return (TotalSize * 1024 * 1024);
652}
653
654/* ------------------------------------------------------------------------- */
655
656
657static int test_dram (unsigned long ramsize)
658{
659 /* not yet implemented */
660 return (1);
661}
662
wdenk7d393ae2002-10-25 21:08:05 +0000663int misc_init_r (void)
664{
wdenk7205e402003-09-10 22:30:53 +0000665 /* adjust flash start and size as well as the offset */
666 gd->bd->bi_flashstart=0-flash_info[0].size;
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200667 gd->bd->bi_flashsize=flash_info[0].size-CONFIG_SYS_MONITOR_LEN;
wdenk7205e402003-09-10 22:30:53 +0000668 gd->bd->bi_flashoffset=0;
669
670 /* if PIP405 has booted from PCI, reset CCR0[24] as described in errata PCI_18 */
Stefan Roesed1c3b272009-09-09 16:25:29 +0200671 if (mfdcr(CPC0_PSR) & PSR_ROM_LOC)
Matthias Fuchs58ea1422009-07-22 17:27:56 +0200672 mtspr(SPRN_CCR0, (mfspr(SPRN_CCR0) & ~0x80));
wdenk7205e402003-09-10 22:30:53 +0000673
wdenk7d393ae2002-10-25 21:08:05 +0000674 return (0);
675}
676
677/***************************************************************************
678 * some helping routines
679 */
680
681int overwrite_console (void)
682{
York Sun472d5462013-04-01 11:29:11 -0700683 /* return true if console should be overwritten */
684 return in8(CONFIG_PORT_ADDR) & 0x1;
wdenk7d393ae2002-10-25 21:08:05 +0000685}
686
687
wdenk7d393ae2002-10-25 21:08:05 +0000688extern int isa_init (void);
689
690
691void print_pip405_rev (void)
692{
693 unsigned char part, vers, cfg;
694
695 part = in8 (PLD_PART_REG);
696 vers = in8 (PLD_VERS_REG);
697 cfg = in8 (PLD_BOARD_CFG_REG);
698 printf ("Rev: PIP405-%d Rev %c PLD%d %d PLD%d %d\n",
699 16 - ((cfg >> 4) & 0xf), (cfg & 0xf) + 'A', part & 0xf,
700 vers & 0xf, (part >> 4) & 0xf, (vers >> 4) & 0xf);
701}
702
703extern void check_env(void);
704
705
706int last_stage_init (void)
707{
708 print_pip405_rev ();
709 isa_init ();
Jean-Christophe PLAGNIOL-VILLARD28c34502009-05-16 12:14:56 +0200710 stdio_print_current_devices ();
wdenk7d393ae2002-10-25 21:08:05 +0000711 check_env();
712 return 0;
713}
714
715/************************************************************************
716* Print PIP405 Info
717************************************************************************/
718void print_pip405_info (void)
719{
720 unsigned char part, vers, cfg, ledu, sysman, flashcom, can, serpwr,
721 compwr, nicvga, scsirst;
722
723 part = in8 (PLD_PART_REG);
724 vers = in8 (PLD_VERS_REG);
725 cfg = in8 (PLD_BOARD_CFG_REG);
726 ledu = in8 (PLD_LED_USER_REG);
727 sysman = in8 (PLD_SYS_MAN_REG);
728 flashcom = in8 (PLD_FLASH_COM_REG);
729 can = in8 (PLD_CAN_REG);
730 serpwr = in8 (PLD_SER_PWR_REG);
731 compwr = in8 (PLD_COM_PWR_REG);
732 nicvga = in8 (PLD_NIC_VGA_REG);
733 scsirst = in8 (PLD_SCSI_RST_REG);
734 printf ("PLD Part %d version %d\n",
735 part & 0xf, vers & 0xf);
736 printf ("PLD Part %d version %d\n",
737 (part >> 4) & 0xf, (vers >> 4) & 0xf);
738 printf ("Board Revision %c\n", (cfg & 0xf) + 'A');
739 printf ("Population Options %d %d %d %d\n",
740 (cfg >> 4) & 0x1, (cfg >> 5) & 0x1,
741 (cfg >> 6) & 0x1, (cfg >> 7) & 0x1);
742 printf ("User LED0 %s User LED1 %s\n",
743 ((ledu & 0x1) == 0x1) ? "on" : "off",
744 ((ledu & 0x2) == 0x2) ? "on" : "off");
745 printf ("Additionally Options %d %d\n",
746 (ledu >> 2) & 0x1, (ledu >> 3) & 0x1);
747 printf ("User Config Switch %d %d %d %d\n",
748 (ledu >> 4) & 0x1, (ledu >> 5) & 0x1,
749 (ledu >> 6) & 0x1, (ledu >> 7) & 0x1);
750 switch (sysman & 0x3) {
751 case 0:
752 printf ("PCI Clocks are running\n");
753 break;
754 case 1:
755 printf ("PCI Clocks are stopped in POS State\n");
756 break;
757 case 2:
758 printf ("PCI Clocks are stopped when PCI_STP# is asserted\n");
759 break;
760 case 3:
761 printf ("PCI Clocks are stopped\n");
762 break;
763 }
764 switch ((sysman >> 2) & 0x3) {
765 case 0:
766 printf ("Main Clocks are running\n");
767 break;
768 case 1:
769 printf ("Main Clocks are stopped in POS State\n");
770 break;
771 case 2:
772 case 3:
773 printf ("PCI Clocks are stopped\n");
774 break;
775 }
776 printf ("INIT asserts %sINT2# (SMI)\n",
777 ((sysman & 0x10) == 0x10) ? "" : "not ");
778 printf ("INIT asserts %sINT1# (NMI)\n",
779 ((sysman & 0x20) == 0x20) ? "" : "not ");
780 printf ("INIT occured %d\n", (sysman >> 6) & 0x1);
781 printf ("SER1 is routed to %s\n",
782 ((flashcom & 0x1) == 0x1) ? "RS485" : "RS232");
783 printf ("COM2 is routed to %s\n",
784 ((flashcom & 0x2) == 0x2) ? "RS485" : "RS232");
785 printf ("RS485 is configured as %s duplex\n",
786 ((flashcom & 0x4) == 0x4) ? "full" : "half");
787 printf ("RS485 is connected to %s\n",
788 ((flashcom & 0x8) == 0x8) ? "COM1" : "COM2");
789 printf ("SER1 uses handshakes %s\n",
790 ((flashcom & 0x10) == 0x10) ? "DTR/DSR" : "RTS/CTS");
791 printf ("Bootflash is %swriteprotected\n",
792 ((flashcom & 0x20) == 0x20) ? "not " : "");
793 printf ("Bootflash VPP is %s\n",
794 ((flashcom & 0x40) == 0x40) ? "on" : "off");
795 printf ("Bootsector is %swriteprotected\n",
796 ((flashcom & 0x80) == 0x80) ? "not " : "");
797 switch ((can) & 0x3) {
798 case 0:
799 printf ("CAN Controller is on address 0x1000..0x10FF\n");
800 break;
801 case 1:
802 printf ("CAN Controller is on address 0x8000..0x80FF\n");
803 break;
804 case 2:
805 printf ("CAN Controller is on address 0xE000..0xE0FF\n");
806 break;
807 case 3:
808 printf ("CAN Controller is disabled\n");
809 break;
810 }
811 switch ((can >> 2) & 0x3) {
812 case 0:
813 printf ("CAN Controller Reset is ISA Reset\n");
814 break;
815 case 1:
816 printf ("CAN Controller Reset is ISA Reset and POS State\n");
817 break;
818 case 2:
819 case 3:
820 printf ("CAN Controller is in reset\n");
821 break;
822 }
823 if (((can >> 4) < 3) || ((can >> 4) == 8) || ((can >> 4) == 13))
824 printf ("CAN Interrupt is disabled\n");
825 else
826 printf ("CAN Interrupt is ISA INT%d\n", (can >> 4) & 0xf);
827 switch (serpwr & 0x3) {
828 case 0:
829 printf ("SER0 Drivers are enabled\n");
830 break;
831 case 1:
832 printf ("SER0 Drivers are disabled in the POS state\n");
833 break;
834 case 2:
835 case 3:
836 printf ("SER0 Drivers are disabled\n");
837 break;
838 }
839 switch ((serpwr >> 2) & 0x3) {
840 case 0:
841 printf ("SER1 Drivers are enabled\n");
842 break;
843 case 1:
844 printf ("SER1 Drivers are disabled in the POS state\n");
845 break;
846 case 2:
847 case 3:
848 printf ("SER1 Drivers are disabled\n");
849 break;
850 }
851 switch (compwr & 0x3) {
852 case 0:
853 printf ("COM1 Drivers are enabled\n");
854 break;
855 case 1:
856 printf ("COM1 Drivers are disabled in the POS state\n");
857 break;
858 case 2:
859 case 3:
860 printf ("COM1 Drivers are disabled\n");
861 break;
862 }
863 switch ((compwr >> 2) & 0x3) {
864 case 0:
865 printf ("COM2 Drivers are enabled\n");
866 break;
867 case 1:
868 printf ("COM2 Drivers are disabled in the POS state\n");
869 break;
870 case 2:
871 case 3:
872 printf ("COM2 Drivers are disabled\n");
873 break;
874 }
875 switch ((nicvga) & 0x3) {
876 case 0:
877 printf ("PHY is running\n");
878 break;
879 case 1:
880 printf ("PHY is in Power save mode in POS state\n");
881 break;
882 case 2:
883 case 3:
884 printf ("PHY is in Power save mode\n");
885 break;
886 }
887 switch ((nicvga >> 2) & 0x3) {
888 case 0:
889 printf ("VGA is running\n");
890 break;
891 case 1:
892 printf ("VGA is in Power save mode in POS state\n");
893 break;
894 case 2:
895 case 3:
896 printf ("VGA is in Power save mode\n");
897 break;
898 }
899 printf ("PHY is %sreseted\n", ((nicvga & 0x10) == 0x10) ? "" : "not ");
900 printf ("VGA is %sreseted\n", ((nicvga & 0x20) == 0x20) ? "" : "not ");
901 printf ("Reserved Configuration is %d %d\n", (nicvga >> 6) & 0x1,
902 (nicvga >> 7) & 0x1);
903 switch ((scsirst) & 0x3) {
904 case 0:
905 printf ("SCSI Controller is running\n");
906 break;
907 case 1:
908 printf ("SCSI Controller is in Power save mode in POS state\n");
909 break;
910 case 2:
911 case 3:
912 printf ("SCSI Controller is in Power save mode\n");
913 break;
914 }
915 printf ("SCSI termination is %s\n",
916 ((scsirst & 0x4) == 0x4) ? "disabled" : "enabled");
917 printf ("SCSI Controller is %sreseted\n",
918 ((scsirst & 0x10) == 0x10) ? "" : "not ");
919 printf ("IDE disks are %sreseted\n",
920 ((scsirst & 0x20) == 0x20) ? "" : "not ");
921 printf ("ISA Bus is %sreseted\n",
922 ((scsirst & 0x40) == 0x40) ? "" : "not ");
923 printf ("Super IO is %sreseted\n",
924 ((scsirst & 0x80) == 0x80) ? "" : "not ");
925}
926
927void user_led0 (unsigned char on)
928{
York Sun472d5462013-04-01 11:29:11 -0700929 if (on == true)
wdenk7d393ae2002-10-25 21:08:05 +0000930 out8 (PLD_LED_USER_REG, (in8 (PLD_LED_USER_REG) | 0x1));
931 else
932 out8 (PLD_LED_USER_REG, (in8 (PLD_LED_USER_REG) & 0xfe));
933}
934
935void user_led1 (unsigned char on)
936{
York Sun472d5462013-04-01 11:29:11 -0700937 if (on == true)
wdenk7d393ae2002-10-25 21:08:05 +0000938 out8 (PLD_LED_USER_REG, (in8 (PLD_LED_USER_REG) | 0x2));
939 else
940 out8 (PLD_LED_USER_REG, (in8 (PLD_LED_USER_REG) & 0xfd));
941}
942
943void ide_set_reset (int idereset)
944{
945 /* if reset = 1 IDE reset will be asserted */
946 unsigned char resreg;
947
948 resreg = in8 (PLD_SCSI_RST_REG);
949 if (idereset == 1)
950 resreg |= 0x20;
951 else {
952 udelay(10000);
953 resreg &= 0xdf;
954 }
955 out8 (PLD_SCSI_RST_REG, resreg);
956}