blob: 196989b3864f9b709f571e83e4959fef25e31eb0 [file] [log] [blame]
wdenk682011f2003-06-03 23:54:09 +00001/**************************************************************************
Andre Schwarzac3315c2008-03-06 16:45:44 +01002Intel Pro 1000 for ppcboot/das-u-boot
wdenk682011f2003-06-03 23:54:09 +00003Drivers are port from Intel's Linux driver e1000-4.3.15
4and from Etherboot pro 1000 driver by mrakes at vivato dot net
5tested on both gig copper and gig fiber boards
6***************************************************************************/
7/*******************************************************************************
8
wdenk8bde7f72003-06-27 21:31:46 +00009
wdenk682011f2003-06-03 23:54:09 +000010 Copyright(c) 1999 - 2002 Intel Corporation. All rights reserved.
wdenk8bde7f72003-06-27 21:31:46 +000011
Wolfgang Denk1a459662013-07-08 09:37:19 +020012 * SPDX-License-Identifier: GPL-2.0+
wdenk8bde7f72003-06-27 21:31:46 +000013
wdenk682011f2003-06-03 23:54:09 +000014 Contact Information:
15 Linux NICS <linux.nics@intel.com>
16 Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
17
18*******************************************************************************/
19/*
20 * Copyright (C) Archway Digital Solutions.
21 *
22 * written by Chrsitopher Li <cli at arcyway dot com> or <chrisl at gnuchina dot org>
23 * 2/9/2002
24 *
25 * Copyright (C) Linux Networx.
26 * Massive upgrade to work with the new intel gigabit NICs.
27 * <ebiederman at lnxi dot com>
Roy Zang2c2668f2011-01-21 11:29:38 +080028 *
29 * Copyright 2011 Freescale Semiconductor, Inc.
wdenk682011f2003-06-03 23:54:09 +000030 */
31
Simon Glassc752cd22015-08-19 09:33:38 -060032#include <common.h>
Simon Glassc6d80a12015-08-19 09:33:40 -060033#include <dm.h>
Simon Glass5c5e7072015-08-19 09:33:39 -060034#include <errno.h>
Simon Glasscf92e052015-09-02 17:24:58 -060035#include <memalign.h>
Simon Glass5c5e7072015-08-19 09:33:39 -060036#include <pci.h>
wdenk682011f2003-06-03 23:54:09 +000037#include "e1000.h"
38
wdenk682011f2003-06-03 23:54:09 +000039#define TOUT_LOOP 100000
40
Bin Meng81dab9a2016-02-02 05:58:01 -080041#ifdef CONFIG_DM_ETH
42#define virt_to_bus(devno, v) dm_pci_virt_to_mem(devno, (void *) (v))
43#define bus_to_phys(devno, a) dm_pci_mem_to_phys(devno, a)
44#else
Timur Tabif81ecb52009-08-17 15:55:38 -050045#define virt_to_bus(devno, v) pci_virt_to_mem(devno, (void *) (v))
wdenk682011f2003-06-03 23:54:09 +000046#define bus_to_phys(devno, a) pci_mem_to_phys(devno, a)
Bin Meng81dab9a2016-02-02 05:58:01 -080047#endif
wdenk682011f2003-06-03 23:54:09 +000048
Roy Zang9ea005f2009-08-22 03:49:52 +080049#define E1000_DEFAULT_PCI_PBA 0x00000030
50#define E1000_DEFAULT_PCIE_PBA 0x000a0026
wdenk682011f2003-06-03 23:54:09 +000051
52/* NIC specific static variables go here */
53
Marek Vasut873e8e02014-08-08 07:41:38 -070054/* Intel i210 needs the DMA descriptor rings aligned to 128b */
55#define E1000_BUFFER_ALIGN 128
wdenk682011f2003-06-03 23:54:09 +000056
Simon Glassc6d80a12015-08-19 09:33:40 -060057/*
58 * TODO(sjg@chromium.org): Even with driver model we share these buffers.
59 * Concurrent receiving on multiple active Ethernet devices will not work.
60 * Normally U-Boot does not support this anyway. To fix it in this driver,
61 * move these buffers and the tx/rx pointers to struct e1000_hw.
62 */
Marek Vasut873e8e02014-08-08 07:41:38 -070063DEFINE_ALIGN_BUFFER(struct e1000_tx_desc, tx_base, 16, E1000_BUFFER_ALIGN);
64DEFINE_ALIGN_BUFFER(struct e1000_rx_desc, rx_base, 16, E1000_BUFFER_ALIGN);
65DEFINE_ALIGN_BUFFER(unsigned char, packet, 4096, E1000_BUFFER_ALIGN);
wdenk682011f2003-06-03 23:54:09 +000066
67static int tx_tail;
68static int rx_tail, rx_last;
Simon Glassc6d80a12015-08-19 09:33:40 -060069#ifdef CONFIG_DM_ETH
70static int num_cards; /* Number of E1000 devices seen so far */
71#endif
wdenk682011f2003-06-03 23:54:09 +000072
Kyle Moffettd60626f82011-10-18 11:05:26 +000073static struct pci_device_id e1000_supported[] = {
Simon Glass5c5e7072015-08-19 09:33:39 -060074 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82542) },
75 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82543GC_FIBER) },
76 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82543GC_COPPER) },
77 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544EI_COPPER) },
78 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544EI_FIBER) },
79 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544GC_COPPER) },
80 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544GC_LOM) },
81 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82540EM) },
82 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82545EM_COPPER) },
83 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82545GM_COPPER) },
84 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546EB_COPPER) },
85 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82545EM_FIBER) },
86 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546EB_FIBER) },
87 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546GB_COPPER) },
88 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82540EM_LOM) },
89 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82541ER) },
90 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82541GI_LF) },
Roy Zangaa070782009-07-31 13:34:02 +080091 /* E1000 PCIe card */
Simon Glass5c5e7072015-08-19 09:33:39 -060092 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_COPPER) },
93 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_FIBER) },
94 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_SERDES) },
95 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_QUAD_COPPER) },
96 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571PT_QUAD_COPPER) },
97 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_QUAD_FIBER) },
98 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_QUAD_COPPER_LOWPROFILE) },
99 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_SERDES_DUAL) },
100 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_SERDES_QUAD) },
101 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI_COPPER) },
102 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI_FIBER) },
103 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI_SERDES) },
104 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI) },
105 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82573E) },
106 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82573E_IAMT) },
107 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82573L) },
108 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82574L) },
109 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546GB_QUAD_COPPER_KSP3) },
110 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_COPPER_DPT) },
111 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_SERDES_DPT) },
112 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_COPPER_SPT) },
113 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_SERDES_SPT) },
114 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_UNPROGRAMMED) },
115 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I211_UNPROGRAMMED) },
116 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_COPPER) },
117 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I211_COPPER) },
118 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_COPPER_FLASHLESS) },
119 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_SERDES) },
120 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_SERDES_FLASHLESS) },
121 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_1000BASEKX) },
Marek Vasut95186062014-08-08 07:41:39 -0700122
Stefan Althoefer1bc43432008-12-20 19:40:41 +0100123 {}
wdenk682011f2003-06-03 23:54:09 +0000124};
125
126/* Function forward declarations */
Simon Glass5c5e7072015-08-19 09:33:39 -0600127static int e1000_setup_link(struct e1000_hw *hw);
128static int e1000_setup_fiber_link(struct e1000_hw *hw);
129static int e1000_setup_copper_link(struct e1000_hw *hw);
wdenk682011f2003-06-03 23:54:09 +0000130static int e1000_phy_setup_autoneg(struct e1000_hw *hw);
131static void e1000_config_collision_dist(struct e1000_hw *hw);
132static int e1000_config_mac_to_phy(struct e1000_hw *hw);
133static int e1000_config_fc_after_link_up(struct e1000_hw *hw);
Simon Glass5c5e7072015-08-19 09:33:39 -0600134static int e1000_check_for_link(struct e1000_hw *hw);
wdenk682011f2003-06-03 23:54:09 +0000135static int e1000_wait_autoneg(struct e1000_hw *hw);
Roy Zangaa070782009-07-31 13:34:02 +0800136static int e1000_get_speed_and_duplex(struct e1000_hw *hw, uint16_t * speed,
wdenk682011f2003-06-03 23:54:09 +0000137 uint16_t * duplex);
138static int e1000_read_phy_reg(struct e1000_hw *hw, uint32_t reg_addr,
139 uint16_t * phy_data);
140static int e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr,
141 uint16_t phy_data);
Roy Zangaa070782009-07-31 13:34:02 +0800142static int32_t e1000_phy_hw_reset(struct e1000_hw *hw);
wdenk682011f2003-06-03 23:54:09 +0000143static int e1000_phy_reset(struct e1000_hw *hw);
144static int e1000_detect_gig_phy(struct e1000_hw *hw);
Roy Zangaa070782009-07-31 13:34:02 +0800145static void e1000_set_media_type(struct e1000_hw *hw);
wdenk682011f2003-06-03 23:54:09 +0000146
Roy Zangaa070782009-07-31 13:34:02 +0800147static int32_t e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask);
Tim Harvey7e2d9912015-05-19 10:01:18 -0700148static void e1000_swfw_sync_release(struct e1000_hw *hw, uint16_t mask);
Roy Zangaa070782009-07-31 13:34:02 +0800149static int32_t e1000_check_phy_reset_block(struct e1000_hw *hw);
wdenk682011f2003-06-03 23:54:09 +0000150
Rojhalat Ibrahim8712adf2013-10-07 18:30:39 +0200151#ifndef CONFIG_E1000_NO_NVM
152static void e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw);
Roy Zangecbd2072009-08-11 03:48:05 +0800153static int32_t e1000_read_eeprom(struct e1000_hw *hw, uint16_t offset,
154 uint16_t words,
155 uint16_t *data);
wdenk682011f2003-06-03 23:54:09 +0000156/******************************************************************************
157 * Raises the EEPROM's clock input.
158 *
159 * hw - Struct containing variables accessed by shared code
160 * eecd - EECD's current value
161 *****************************************************************************/
Kyle Moffett2326a942011-10-18 11:05:28 +0000162void e1000_raise_ee_clk(struct e1000_hw *hw, uint32_t * eecd)
wdenk682011f2003-06-03 23:54:09 +0000163{
164 /* Raise the clock input to the EEPROM (by setting the SK bit), and then
165 * wait 50 microseconds.
166 */
167 *eecd = *eecd | E1000_EECD_SK;
168 E1000_WRITE_REG(hw, EECD, *eecd);
169 E1000_WRITE_FLUSH(hw);
170 udelay(50);
171}
172
173/******************************************************************************
174 * Lowers the EEPROM's clock input.
175 *
wdenk8bde7f72003-06-27 21:31:46 +0000176 * hw - Struct containing variables accessed by shared code
wdenk682011f2003-06-03 23:54:09 +0000177 * eecd - EECD's current value
178 *****************************************************************************/
Kyle Moffett2326a942011-10-18 11:05:28 +0000179void e1000_lower_ee_clk(struct e1000_hw *hw, uint32_t * eecd)
wdenk682011f2003-06-03 23:54:09 +0000180{
wdenk8bde7f72003-06-27 21:31:46 +0000181 /* Lower the clock input to the EEPROM (by clearing the SK bit), and then
182 * wait 50 microseconds.
wdenk682011f2003-06-03 23:54:09 +0000183 */
184 *eecd = *eecd & ~E1000_EECD_SK;
185 E1000_WRITE_REG(hw, EECD, *eecd);
186 E1000_WRITE_FLUSH(hw);
187 udelay(50);
188}
189
190/******************************************************************************
191 * Shift data bits out to the EEPROM.
192 *
193 * hw - Struct containing variables accessed by shared code
194 * data - data to send to the EEPROM
195 * count - number of bits to shift out
196 *****************************************************************************/
197static void
198e1000_shift_out_ee_bits(struct e1000_hw *hw, uint16_t data, uint16_t count)
199{
200 uint32_t eecd;
201 uint32_t mask;
202
203 /* We need to shift "count" bits out to the EEPROM. So, value in the
204 * "data" parameter will be shifted out to the EEPROM one bit at a time.
wdenk8bde7f72003-06-27 21:31:46 +0000205 * In order to do this, "data" must be broken down into bits.
wdenk682011f2003-06-03 23:54:09 +0000206 */
207 mask = 0x01 << (count - 1);
208 eecd = E1000_READ_REG(hw, EECD);
209 eecd &= ~(E1000_EECD_DO | E1000_EECD_DI);
210 do {
211 /* A "1" is shifted out to the EEPROM by setting bit "DI" to a "1",
212 * and then raising and then lowering the clock (the SK bit controls
213 * the clock input to the EEPROM). A "0" is shifted out to the EEPROM
214 * by setting "DI" to "0" and then raising and then lowering the clock.
215 */
216 eecd &= ~E1000_EECD_DI;
217
218 if (data & mask)
219 eecd |= E1000_EECD_DI;
220
221 E1000_WRITE_REG(hw, EECD, eecd);
222 E1000_WRITE_FLUSH(hw);
223
224 udelay(50);
225
226 e1000_raise_ee_clk(hw, &eecd);
227 e1000_lower_ee_clk(hw, &eecd);
228
229 mask = mask >> 1;
230
231 } while (mask);
232
233 /* We leave the "DI" bit set to "0" when we leave this routine. */
234 eecd &= ~E1000_EECD_DI;
235 E1000_WRITE_REG(hw, EECD, eecd);
236}
237
238/******************************************************************************
239 * Shift data bits in from the EEPROM
240 *
241 * hw - Struct containing variables accessed by shared code
242 *****************************************************************************/
243static uint16_t
Roy Zangaa070782009-07-31 13:34:02 +0800244e1000_shift_in_ee_bits(struct e1000_hw *hw, uint16_t count)
wdenk682011f2003-06-03 23:54:09 +0000245{
246 uint32_t eecd;
247 uint32_t i;
248 uint16_t data;
249
Roy Zangaa070782009-07-31 13:34:02 +0800250 /* In order to read a register from the EEPROM, we need to shift 'count'
251 * bits in from the EEPROM. Bits are "shifted in" by raising the clock
252 * input to the EEPROM (setting the SK bit), and then reading the
253 * value of the "DO" bit. During this "shifting in" process the
254 * "DI" bit should always be clear.
wdenk682011f2003-06-03 23:54:09 +0000255 */
256
257 eecd = E1000_READ_REG(hw, EECD);
258
259 eecd &= ~(E1000_EECD_DO | E1000_EECD_DI);
260 data = 0;
261
Roy Zangaa070782009-07-31 13:34:02 +0800262 for (i = 0; i < count; i++) {
wdenk682011f2003-06-03 23:54:09 +0000263 data = data << 1;
264 e1000_raise_ee_clk(hw, &eecd);
265
266 eecd = E1000_READ_REG(hw, EECD);
267
268 eecd &= ~(E1000_EECD_DI);
269 if (eecd & E1000_EECD_DO)
270 data |= 1;
271
272 e1000_lower_ee_clk(hw, &eecd);
273 }
274
275 return data;
276}
277
278/******************************************************************************
wdenk682011f2003-06-03 23:54:09 +0000279 * Returns EEPROM to a "standby" state
wdenk8bde7f72003-06-27 21:31:46 +0000280 *
wdenk682011f2003-06-03 23:54:09 +0000281 * hw - Struct containing variables accessed by shared code
282 *****************************************************************************/
Kyle Moffett2326a942011-10-18 11:05:28 +0000283void e1000_standby_eeprom(struct e1000_hw *hw)
wdenk682011f2003-06-03 23:54:09 +0000284{
Roy Zangaa070782009-07-31 13:34:02 +0800285 struct e1000_eeprom_info *eeprom = &hw->eeprom;
wdenk682011f2003-06-03 23:54:09 +0000286 uint32_t eecd;
287
288 eecd = E1000_READ_REG(hw, EECD);
289
Roy Zangaa070782009-07-31 13:34:02 +0800290 if (eeprom->type == e1000_eeprom_microwire) {
291 eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
292 E1000_WRITE_REG(hw, EECD, eecd);
293 E1000_WRITE_FLUSH(hw);
294 udelay(eeprom->delay_usec);
wdenk682011f2003-06-03 23:54:09 +0000295
Roy Zangaa070782009-07-31 13:34:02 +0800296 /* Clock high */
297 eecd |= E1000_EECD_SK;
298 E1000_WRITE_REG(hw, EECD, eecd);
299 E1000_WRITE_FLUSH(hw);
300 udelay(eeprom->delay_usec);
wdenk682011f2003-06-03 23:54:09 +0000301
Roy Zangaa070782009-07-31 13:34:02 +0800302 /* Select EEPROM */
303 eecd |= E1000_EECD_CS;
304 E1000_WRITE_REG(hw, EECD, eecd);
305 E1000_WRITE_FLUSH(hw);
306 udelay(eeprom->delay_usec);
wdenk682011f2003-06-03 23:54:09 +0000307
Roy Zangaa070782009-07-31 13:34:02 +0800308 /* Clock low */
309 eecd &= ~E1000_EECD_SK;
310 E1000_WRITE_REG(hw, EECD, eecd);
311 E1000_WRITE_FLUSH(hw);
312 udelay(eeprom->delay_usec);
313 } else if (eeprom->type == e1000_eeprom_spi) {
314 /* Toggle CS to flush commands */
315 eecd |= E1000_EECD_CS;
316 E1000_WRITE_REG(hw, EECD, eecd);
317 E1000_WRITE_FLUSH(hw);
318 udelay(eeprom->delay_usec);
319 eecd &= ~E1000_EECD_CS;
320 E1000_WRITE_REG(hw, EECD, eecd);
321 E1000_WRITE_FLUSH(hw);
322 udelay(eeprom->delay_usec);
323 }
324}
325
326/***************************************************************************
327* Description: Determines if the onboard NVM is FLASH or EEPROM.
328*
329* hw - Struct containing variables accessed by shared code
330****************************************************************************/
York Sun472d5462013-04-01 11:29:11 -0700331static bool e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw)
Roy Zangaa070782009-07-31 13:34:02 +0800332{
333 uint32_t eecd = 0;
334
335 DEBUGFUNC();
336
337 if (hw->mac_type == e1000_ich8lan)
York Sun472d5462013-04-01 11:29:11 -0700338 return false;
Roy Zangaa070782009-07-31 13:34:02 +0800339
Roy Zang2c2668f2011-01-21 11:29:38 +0800340 if (hw->mac_type == e1000_82573 || hw->mac_type == e1000_82574) {
Roy Zangaa070782009-07-31 13:34:02 +0800341 eecd = E1000_READ_REG(hw, EECD);
342
343 /* Isolate bits 15 & 16 */
344 eecd = ((eecd >> 15) & 0x03);
345
346 /* If both bits are set, device is Flash type */
347 if (eecd == 0x03)
York Sun472d5462013-04-01 11:29:11 -0700348 return false;
Roy Zangaa070782009-07-31 13:34:02 +0800349 }
York Sun472d5462013-04-01 11:29:11 -0700350 return true;
Roy Zangaa070782009-07-31 13:34:02 +0800351}
352
353/******************************************************************************
354 * Prepares EEPROM for access
355 *
356 * hw - Struct containing variables accessed by shared code
357 *
358 * Lowers EEPROM clock. Clears input pin. Sets the chip select pin. This
359 * function should be called before issuing a command to the EEPROM.
360 *****************************************************************************/
Kyle Moffett2326a942011-10-18 11:05:28 +0000361int32_t e1000_acquire_eeprom(struct e1000_hw *hw)
Roy Zangaa070782009-07-31 13:34:02 +0800362{
363 struct e1000_eeprom_info *eeprom = &hw->eeprom;
364 uint32_t eecd, i = 0;
365
Timur Tabif81ecb52009-08-17 15:55:38 -0500366 DEBUGFUNC();
Roy Zangaa070782009-07-31 13:34:02 +0800367
368 if (e1000_swfw_sync_acquire(hw, E1000_SWFW_EEP_SM))
369 return -E1000_ERR_SWFW_SYNC;
370 eecd = E1000_READ_REG(hw, EECD);
371
Marek Vasut95186062014-08-08 07:41:39 -0700372 if (hw->mac_type != e1000_82573 && hw->mac_type != e1000_82574) {
Roy Zangaa070782009-07-31 13:34:02 +0800373 /* Request EEPROM Access */
374 if (hw->mac_type > e1000_82544) {
375 eecd |= E1000_EECD_REQ;
376 E1000_WRITE_REG(hw, EECD, eecd);
377 eecd = E1000_READ_REG(hw, EECD);
378 while ((!(eecd & E1000_EECD_GNT)) &&
379 (i < E1000_EEPROM_GRANT_ATTEMPTS)) {
380 i++;
381 udelay(5);
382 eecd = E1000_READ_REG(hw, EECD);
383 }
384 if (!(eecd & E1000_EECD_GNT)) {
385 eecd &= ~E1000_EECD_REQ;
386 E1000_WRITE_REG(hw, EECD, eecd);
387 DEBUGOUT("Could not acquire EEPROM grant\n");
388 return -E1000_ERR_EEPROM;
389 }
390 }
391 }
392
393 /* Setup EEPROM for Read/Write */
394
395 if (eeprom->type == e1000_eeprom_microwire) {
396 /* Clear SK and DI */
397 eecd &= ~(E1000_EECD_DI | E1000_EECD_SK);
398 E1000_WRITE_REG(hw, EECD, eecd);
399
400 /* Set CS */
401 eecd |= E1000_EECD_CS;
402 E1000_WRITE_REG(hw, EECD, eecd);
403 } else if (eeprom->type == e1000_eeprom_spi) {
404 /* Clear SK and CS */
405 eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
406 E1000_WRITE_REG(hw, EECD, eecd);
407 udelay(1);
408 }
409
410 return E1000_SUCCESS;
411}
412
413/******************************************************************************
414 * Sets up eeprom variables in the hw struct. Must be called after mac_type
415 * is configured. Additionally, if this is ICH8, the flash controller GbE
416 * registers must be mapped, or this will crash.
417 *
418 * hw - Struct containing variables accessed by shared code
419 *****************************************************************************/
420static int32_t e1000_init_eeprom_params(struct e1000_hw *hw)
421{
422 struct e1000_eeprom_info *eeprom = &hw->eeprom;
Marek Vasut95186062014-08-08 07:41:39 -0700423 uint32_t eecd;
Roy Zangaa070782009-07-31 13:34:02 +0800424 int32_t ret_val = E1000_SUCCESS;
425 uint16_t eeprom_size;
426
Marek Vasut95186062014-08-08 07:41:39 -0700427 if (hw->mac_type == e1000_igb)
428 eecd = E1000_READ_REG(hw, I210_EECD);
429 else
430 eecd = E1000_READ_REG(hw, EECD);
431
Timur Tabif81ecb52009-08-17 15:55:38 -0500432 DEBUGFUNC();
Roy Zangaa070782009-07-31 13:34:02 +0800433
434 switch (hw->mac_type) {
435 case e1000_82542_rev2_0:
436 case e1000_82542_rev2_1:
437 case e1000_82543:
438 case e1000_82544:
439 eeprom->type = e1000_eeprom_microwire;
440 eeprom->word_size = 64;
441 eeprom->opcode_bits = 3;
442 eeprom->address_bits = 6;
443 eeprom->delay_usec = 50;
York Sun472d5462013-04-01 11:29:11 -0700444 eeprom->use_eerd = false;
445 eeprom->use_eewr = false;
Roy Zangaa070782009-07-31 13:34:02 +0800446 break;
447 case e1000_82540:
448 case e1000_82545:
449 case e1000_82545_rev_3:
450 case e1000_82546:
451 case e1000_82546_rev_3:
452 eeprom->type = e1000_eeprom_microwire;
453 eeprom->opcode_bits = 3;
454 eeprom->delay_usec = 50;
455 if (eecd & E1000_EECD_SIZE) {
456 eeprom->word_size = 256;
457 eeprom->address_bits = 8;
458 } else {
459 eeprom->word_size = 64;
460 eeprom->address_bits = 6;
461 }
York Sun472d5462013-04-01 11:29:11 -0700462 eeprom->use_eerd = false;
463 eeprom->use_eewr = false;
Roy Zangaa070782009-07-31 13:34:02 +0800464 break;
465 case e1000_82541:
466 case e1000_82541_rev_2:
467 case e1000_82547:
468 case e1000_82547_rev_2:
469 if (eecd & E1000_EECD_TYPE) {
470 eeprom->type = e1000_eeprom_spi;
471 eeprom->opcode_bits = 8;
472 eeprom->delay_usec = 1;
473 if (eecd & E1000_EECD_ADDR_BITS) {
474 eeprom->page_size = 32;
475 eeprom->address_bits = 16;
476 } else {
477 eeprom->page_size = 8;
478 eeprom->address_bits = 8;
479 }
480 } else {
481 eeprom->type = e1000_eeprom_microwire;
482 eeprom->opcode_bits = 3;
483 eeprom->delay_usec = 50;
484 if (eecd & E1000_EECD_ADDR_BITS) {
485 eeprom->word_size = 256;
486 eeprom->address_bits = 8;
487 } else {
488 eeprom->word_size = 64;
489 eeprom->address_bits = 6;
490 }
491 }
York Sun472d5462013-04-01 11:29:11 -0700492 eeprom->use_eerd = false;
493 eeprom->use_eewr = false;
Roy Zangaa070782009-07-31 13:34:02 +0800494 break;
495 case e1000_82571:
496 case e1000_82572:
497 eeprom->type = e1000_eeprom_spi;
498 eeprom->opcode_bits = 8;
499 eeprom->delay_usec = 1;
500 if (eecd & E1000_EECD_ADDR_BITS) {
501 eeprom->page_size = 32;
502 eeprom->address_bits = 16;
503 } else {
504 eeprom->page_size = 8;
505 eeprom->address_bits = 8;
506 }
York Sun472d5462013-04-01 11:29:11 -0700507 eeprom->use_eerd = false;
508 eeprom->use_eewr = false;
Roy Zangaa070782009-07-31 13:34:02 +0800509 break;
510 case e1000_82573:
Roy Zang2c2668f2011-01-21 11:29:38 +0800511 case e1000_82574:
Roy Zangaa070782009-07-31 13:34:02 +0800512 eeprom->type = e1000_eeprom_spi;
513 eeprom->opcode_bits = 8;
514 eeprom->delay_usec = 1;
515 if (eecd & E1000_EECD_ADDR_BITS) {
516 eeprom->page_size = 32;
517 eeprom->address_bits = 16;
518 } else {
519 eeprom->page_size = 8;
520 eeprom->address_bits = 8;
521 }
York Sun472d5462013-04-01 11:29:11 -0700522 if (e1000_is_onboard_nvm_eeprom(hw) == false) {
Marek Vasut95186062014-08-08 07:41:39 -0700523 eeprom->use_eerd = true;
524 eeprom->use_eewr = true;
525
Roy Zangaa070782009-07-31 13:34:02 +0800526 eeprom->type = e1000_eeprom_flash;
527 eeprom->word_size = 2048;
528
529 /* Ensure that the Autonomous FLASH update bit is cleared due to
530 * Flash update issue on parts which use a FLASH for NVM. */
531 eecd &= ~E1000_EECD_AUPDEN;
532 E1000_WRITE_REG(hw, EECD, eecd);
533 }
534 break;
535 case e1000_80003es2lan:
536 eeprom->type = e1000_eeprom_spi;
537 eeprom->opcode_bits = 8;
538 eeprom->delay_usec = 1;
539 if (eecd & E1000_EECD_ADDR_BITS) {
540 eeprom->page_size = 32;
541 eeprom->address_bits = 16;
542 } else {
543 eeprom->page_size = 8;
544 eeprom->address_bits = 8;
545 }
York Sun472d5462013-04-01 11:29:11 -0700546 eeprom->use_eerd = true;
547 eeprom->use_eewr = false;
Roy Zangaa070782009-07-31 13:34:02 +0800548 break;
Marek Vasut95186062014-08-08 07:41:39 -0700549 case e1000_igb:
550 /* i210 has 4k of iNVM mapped as EEPROM */
551 eeprom->type = e1000_eeprom_invm;
552 eeprom->opcode_bits = 8;
553 eeprom->delay_usec = 1;
554 eeprom->page_size = 32;
555 eeprom->address_bits = 16;
556 eeprom->use_eerd = true;
557 eeprom->use_eewr = false;
558 break;
Roy Zangaa070782009-07-31 13:34:02 +0800559 default:
560 break;
561 }
562
Marek Vasut95186062014-08-08 07:41:39 -0700563 if (eeprom->type == e1000_eeprom_spi ||
564 eeprom->type == e1000_eeprom_invm) {
Roy Zangaa070782009-07-31 13:34:02 +0800565 /* eeprom_size will be an enum [0..8] that maps
566 * to eeprom sizes 128B to
567 * 32KB (incremented by powers of 2).
568 */
569 if (hw->mac_type <= e1000_82547_rev_2) {
570 /* Set to default value for initial eeprom read. */
571 eeprom->word_size = 64;
572 ret_val = e1000_read_eeprom(hw, EEPROM_CFG, 1,
573 &eeprom_size);
574 if (ret_val)
575 return ret_val;
576 eeprom_size = (eeprom_size & EEPROM_SIZE_MASK)
577 >> EEPROM_SIZE_SHIFT;
578 /* 256B eeprom size was not supported in earlier
579 * hardware, so we bump eeprom_size up one to
580 * ensure that "1" (which maps to 256B) is never
581 * the result used in the shifting logic below. */
582 if (eeprom_size)
583 eeprom_size++;
584 } else {
585 eeprom_size = (uint16_t)((eecd &
586 E1000_EECD_SIZE_EX_MASK) >>
587 E1000_EECD_SIZE_EX_SHIFT);
588 }
589
590 eeprom->word_size = 1 << (eeprom_size + EEPROM_WORD_SIZE_SHIFT);
591 }
592 return ret_val;
593}
594
595/******************************************************************************
596 * Polls the status bit (bit 1) of the EERD to determine when the read is done.
597 *
598 * hw - Struct containing variables accessed by shared code
599 *****************************************************************************/
600static int32_t
601e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd)
602{
603 uint32_t attempts = 100000;
604 uint32_t i, reg = 0;
605 int32_t done = E1000_ERR_EEPROM;
606
607 for (i = 0; i < attempts; i++) {
Marek Vasut95186062014-08-08 07:41:39 -0700608 if (eerd == E1000_EEPROM_POLL_READ) {
609 if (hw->mac_type == e1000_igb)
610 reg = E1000_READ_REG(hw, I210_EERD);
611 else
612 reg = E1000_READ_REG(hw, EERD);
613 } else {
614 if (hw->mac_type == e1000_igb)
615 reg = E1000_READ_REG(hw, I210_EEWR);
616 else
617 reg = E1000_READ_REG(hw, EEWR);
618 }
Roy Zangaa070782009-07-31 13:34:02 +0800619
620 if (reg & E1000_EEPROM_RW_REG_DONE) {
621 done = E1000_SUCCESS;
622 break;
623 }
624 udelay(5);
625 }
626
627 return done;
628}
629
630/******************************************************************************
631 * Reads a 16 bit word from the EEPROM using the EERD register.
632 *
633 * hw - Struct containing variables accessed by shared code
634 * offset - offset of word in the EEPROM to read
635 * data - word read from the EEPROM
636 * words - number of words to read
637 *****************************************************************************/
638static int32_t
639e1000_read_eeprom_eerd(struct e1000_hw *hw,
640 uint16_t offset,
641 uint16_t words,
642 uint16_t *data)
643{
644 uint32_t i, eerd = 0;
645 int32_t error = 0;
646
647 for (i = 0; i < words; i++) {
648 eerd = ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) +
649 E1000_EEPROM_RW_REG_START;
650
Marek Vasut95186062014-08-08 07:41:39 -0700651 if (hw->mac_type == e1000_igb)
652 E1000_WRITE_REG(hw, I210_EERD, eerd);
653 else
654 E1000_WRITE_REG(hw, EERD, eerd);
655
Roy Zangaa070782009-07-31 13:34:02 +0800656 error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_READ);
657
658 if (error)
659 break;
Marek Vasut95186062014-08-08 07:41:39 -0700660
661 if (hw->mac_type == e1000_igb) {
662 data[i] = (E1000_READ_REG(hw, I210_EERD) >>
Roy Zangaa070782009-07-31 13:34:02 +0800663 E1000_EEPROM_RW_REG_DATA);
Marek Vasut95186062014-08-08 07:41:39 -0700664 } else {
665 data[i] = (E1000_READ_REG(hw, EERD) >>
666 E1000_EEPROM_RW_REG_DATA);
667 }
Roy Zangaa070782009-07-31 13:34:02 +0800668
669 }
670
671 return error;
672}
673
Kyle Moffett2326a942011-10-18 11:05:28 +0000674void e1000_release_eeprom(struct e1000_hw *hw)
Roy Zangaa070782009-07-31 13:34:02 +0800675{
676 uint32_t eecd;
677
678 DEBUGFUNC();
679
680 eecd = E1000_READ_REG(hw, EECD);
681
682 if (hw->eeprom.type == e1000_eeprom_spi) {
683 eecd |= E1000_EECD_CS; /* Pull CS high */
684 eecd &= ~E1000_EECD_SK; /* Lower SCK */
685
686 E1000_WRITE_REG(hw, EECD, eecd);
687
688 udelay(hw->eeprom.delay_usec);
689 } else if (hw->eeprom.type == e1000_eeprom_microwire) {
690 /* cleanup eeprom */
691
692 /* CS on Microwire is active-high */
693 eecd &= ~(E1000_EECD_CS | E1000_EECD_DI);
694
695 E1000_WRITE_REG(hw, EECD, eecd);
696
697 /* Rising edge of clock */
698 eecd |= E1000_EECD_SK;
699 E1000_WRITE_REG(hw, EECD, eecd);
700 E1000_WRITE_FLUSH(hw);
701 udelay(hw->eeprom.delay_usec);
702
703 /* Falling edge of clock */
704 eecd &= ~E1000_EECD_SK;
705 E1000_WRITE_REG(hw, EECD, eecd);
706 E1000_WRITE_FLUSH(hw);
707 udelay(hw->eeprom.delay_usec);
708 }
709
710 /* Stop requesting EEPROM access */
711 if (hw->mac_type > e1000_82544) {
712 eecd &= ~E1000_EECD_REQ;
713 E1000_WRITE_REG(hw, EECD, eecd);
714 }
Tim Harvey7e2d9912015-05-19 10:01:18 -0700715
716 e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM);
Roy Zangaa070782009-07-31 13:34:02 +0800717}
Tim Harvey7e2d9912015-05-19 10:01:18 -0700718
Roy Zangaa070782009-07-31 13:34:02 +0800719/******************************************************************************
720 * Reads a 16 bit word from the EEPROM.
721 *
722 * hw - Struct containing variables accessed by shared code
723 *****************************************************************************/
724static int32_t
725e1000_spi_eeprom_ready(struct e1000_hw *hw)
726{
727 uint16_t retry_count = 0;
728 uint8_t spi_stat_reg;
729
730 DEBUGFUNC();
731
732 /* Read "Status Register" repeatedly until the LSB is cleared. The
733 * EEPROM will signal that the command has been completed by clearing
734 * bit 0 of the internal status register. If it's not cleared within
735 * 5 milliseconds, then error out.
736 */
737 retry_count = 0;
738 do {
739 e1000_shift_out_ee_bits(hw, EEPROM_RDSR_OPCODE_SPI,
740 hw->eeprom.opcode_bits);
741 spi_stat_reg = (uint8_t)e1000_shift_in_ee_bits(hw, 8);
742 if (!(spi_stat_reg & EEPROM_STATUS_RDY_SPI))
743 break;
744
745 udelay(5);
746 retry_count += 5;
747
748 e1000_standby_eeprom(hw);
749 } while (retry_count < EEPROM_MAX_RETRY_SPI);
750
751 /* ATMEL SPI write time could vary from 0-20mSec on 3.3V devices (and
752 * only 0-5mSec on 5V devices)
753 */
754 if (retry_count >= EEPROM_MAX_RETRY_SPI) {
755 DEBUGOUT("SPI EEPROM Status error\n");
756 return -E1000_ERR_EEPROM;
757 }
758
759 return E1000_SUCCESS;
wdenk682011f2003-06-03 23:54:09 +0000760}
761
762/******************************************************************************
763 * Reads a 16 bit word from the EEPROM.
764 *
765 * hw - Struct containing variables accessed by shared code
766 * offset - offset of word in the EEPROM to read
wdenk8bde7f72003-06-27 21:31:46 +0000767 * data - word read from the EEPROM
wdenk682011f2003-06-03 23:54:09 +0000768 *****************************************************************************/
Roy Zangaa070782009-07-31 13:34:02 +0800769static int32_t
770e1000_read_eeprom(struct e1000_hw *hw, uint16_t offset,
771 uint16_t words, uint16_t *data)
wdenk682011f2003-06-03 23:54:09 +0000772{
Roy Zangaa070782009-07-31 13:34:02 +0800773 struct e1000_eeprom_info *eeprom = &hw->eeprom;
wdenk682011f2003-06-03 23:54:09 +0000774 uint32_t i = 0;
wdenk682011f2003-06-03 23:54:09 +0000775
Roy Zangaa070782009-07-31 13:34:02 +0800776 DEBUGFUNC();
777
778 /* If eeprom is not yet detected, do so now */
779 if (eeprom->word_size == 0)
780 e1000_init_eeprom_params(hw);
781
782 /* A check for invalid values: offset too large, too many words,
783 * and not enough words.
784 */
785 if ((offset >= eeprom->word_size) ||
786 (words > eeprom->word_size - offset) ||
787 (words == 0)) {
788 DEBUGOUT("\"words\" parameter out of bounds."
789 "Words = %d, size = %d\n", offset, eeprom->word_size);
790 return -E1000_ERR_EEPROM;
791 }
792
793 /* EEPROM's that don't use EERD to read require us to bit-bang the SPI
794 * directly. In this case, we need to acquire the EEPROM so that
795 * FW or other port software does not interrupt.
796 */
York Sun472d5462013-04-01 11:29:11 -0700797 if (e1000_is_onboard_nvm_eeprom(hw) == true &&
798 hw->eeprom.use_eerd == false) {
Roy Zangaa070782009-07-31 13:34:02 +0800799
800 /* Prepare the EEPROM for bit-bang reading */
801 if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
802 return -E1000_ERR_EEPROM;
803 }
804
805 /* Eerd register EEPROM access requires no eeprom aquire/release */
York Sun472d5462013-04-01 11:29:11 -0700806 if (eeprom->use_eerd == true)
Roy Zangaa070782009-07-31 13:34:02 +0800807 return e1000_read_eeprom_eerd(hw, offset, words, data);
808
Roy Zangaa070782009-07-31 13:34:02 +0800809 /* Set up the SPI or Microwire EEPROM for bit-bang reading. We have
810 * acquired the EEPROM at this point, so any returns should relase it */
811 if (eeprom->type == e1000_eeprom_spi) {
812 uint16_t word_in;
813 uint8_t read_opcode = EEPROM_READ_OPCODE_SPI;
814
815 if (e1000_spi_eeprom_ready(hw)) {
816 e1000_release_eeprom(hw);
wdenk682011f2003-06-03 23:54:09 +0000817 return -E1000_ERR_EEPROM;
818 }
Roy Zangaa070782009-07-31 13:34:02 +0800819
820 e1000_standby_eeprom(hw);
821
822 /* Some SPI eeproms use the 8th address bit embedded in
823 * the opcode */
824 if ((eeprom->address_bits == 8) && (offset >= 128))
825 read_opcode |= EEPROM_A8_OPCODE_SPI;
826
827 /* Send the READ command (opcode + addr) */
828 e1000_shift_out_ee_bits(hw, read_opcode, eeprom->opcode_bits);
829 e1000_shift_out_ee_bits(hw, (uint16_t)(offset*2),
830 eeprom->address_bits);
831
832 /* Read the data. The address of the eeprom internally
833 * increments with each byte (spi) being read, saving on the
834 * overhead of eeprom setup and tear-down. The address
835 * counter will roll over if reading beyond the size of
836 * the eeprom, thus allowing the entire memory to be read
837 * starting from any offset. */
838 for (i = 0; i < words; i++) {
839 word_in = e1000_shift_in_ee_bits(hw, 16);
840 data[i] = (word_in >> 8) | (word_in << 8);
841 }
842 } else if (eeprom->type == e1000_eeprom_microwire) {
843 for (i = 0; i < words; i++) {
844 /* Send the READ command (opcode + addr) */
845 e1000_shift_out_ee_bits(hw,
846 EEPROM_READ_OPCODE_MICROWIRE,
847 eeprom->opcode_bits);
848 e1000_shift_out_ee_bits(hw, (uint16_t)(offset + i),
849 eeprom->address_bits);
850
851 /* Read the data. For microwire, each word requires
852 * the overhead of eeprom setup and tear-down. */
853 data[i] = e1000_shift_in_ee_bits(hw, 16);
854 e1000_standby_eeprom(hw);
855 }
wdenk682011f2003-06-03 23:54:09 +0000856 }
857
wdenk682011f2003-06-03 23:54:09 +0000858 /* End this read operation */
Roy Zangaa070782009-07-31 13:34:02 +0800859 e1000_release_eeprom(hw);
wdenk682011f2003-06-03 23:54:09 +0000860
Roy Zangaa070782009-07-31 13:34:02 +0800861 return E1000_SUCCESS;
wdenk682011f2003-06-03 23:54:09 +0000862}
863
wdenk682011f2003-06-03 23:54:09 +0000864/******************************************************************************
865 * Verifies that the EEPROM has a valid checksum
wdenk8bde7f72003-06-27 21:31:46 +0000866 *
wdenk682011f2003-06-03 23:54:09 +0000867 * hw - Struct containing variables accessed by shared code
868 *
869 * Reads the first 64 16 bit words of the EEPROM and sums the values read.
870 * If the the sum of the 64 16 bit words is 0xBABA, the EEPROM's checksum is
871 * valid.
872 *****************************************************************************/
Kyle Moffett114d7fc2011-10-18 11:05:27 +0000873static int e1000_validate_eeprom_checksum(struct e1000_hw *hw)
wdenk682011f2003-06-03 23:54:09 +0000874{
Kyle Moffett114d7fc2011-10-18 11:05:27 +0000875 uint16_t i, checksum, checksum_reg, *buf;
wdenk682011f2003-06-03 23:54:09 +0000876
877 DEBUGFUNC();
878
Kyle Moffett114d7fc2011-10-18 11:05:27 +0000879 /* Allocate a temporary buffer */
880 buf = malloc(sizeof(buf[0]) * (EEPROM_CHECKSUM_REG + 1));
881 if (!buf) {
Simon Glass5c5e7072015-08-19 09:33:39 -0600882 E1000_ERR(hw, "Unable to allocate EEPROM buffer!\n");
wdenk682011f2003-06-03 23:54:09 +0000883 return -E1000_ERR_EEPROM;
884 }
Kyle Moffett114d7fc2011-10-18 11:05:27 +0000885
886 /* Read the EEPROM */
887 if (e1000_read_eeprom(hw, 0, EEPROM_CHECKSUM_REG + 1, buf) < 0) {
Simon Glass5c5e7072015-08-19 09:33:39 -0600888 E1000_ERR(hw, "Unable to read EEPROM!\n");
Kyle Moffett114d7fc2011-10-18 11:05:27 +0000889 return -E1000_ERR_EEPROM;
890 }
891
892 /* Compute the checksum */
Wolfgang Denk7a341062011-10-28 07:37:04 +0200893 checksum = 0;
Kyle Moffett114d7fc2011-10-18 11:05:27 +0000894 for (i = 0; i < EEPROM_CHECKSUM_REG; i++)
895 checksum += buf[i];
896 checksum = ((uint16_t)EEPROM_SUM) - checksum;
897 checksum_reg = buf[i];
898
899 /* Verify it! */
900 if (checksum == checksum_reg)
901 return 0;
902
903 /* Hrm, verification failed, print an error */
Simon Glass5c5e7072015-08-19 09:33:39 -0600904 E1000_ERR(hw, "EEPROM checksum is incorrect!\n");
905 E1000_ERR(hw, " ...register was 0x%04hx, calculated 0x%04hx\n",
906 checksum_reg, checksum);
Kyle Moffett114d7fc2011-10-18 11:05:27 +0000907
908 return -E1000_ERR_EEPROM;
wdenk682011f2003-06-03 23:54:09 +0000909}
Rojhalat Ibrahim8712adf2013-10-07 18:30:39 +0200910#endif /* CONFIG_E1000_NO_NVM */
Roy Zangecbd2072009-08-11 03:48:05 +0800911
912/*****************************************************************************
913 * Set PHY to class A mode
914 * Assumes the following operations will follow to enable the new class mode.
915 * 1. Do a PHY soft reset
916 * 2. Restart auto-negotiation or force link.
917 *
918 * hw - Struct containing variables accessed by shared code
919 ****************************************************************************/
920static int32_t
921e1000_set_phy_mode(struct e1000_hw *hw)
922{
Rojhalat Ibrahim8712adf2013-10-07 18:30:39 +0200923#ifndef CONFIG_E1000_NO_NVM
Roy Zangecbd2072009-08-11 03:48:05 +0800924 int32_t ret_val;
925 uint16_t eeprom_data;
926
927 DEBUGFUNC();
928
929 if ((hw->mac_type == e1000_82545_rev_3) &&
930 (hw->media_type == e1000_media_type_copper)) {
931 ret_val = e1000_read_eeprom(hw, EEPROM_PHY_CLASS_WORD,
932 1, &eeprom_data);
933 if (ret_val)
934 return ret_val;
935
936 if ((eeprom_data != EEPROM_RESERVED_WORD) &&
937 (eeprom_data & EEPROM_PHY_CLASS_A)) {
938 ret_val = e1000_write_phy_reg(hw,
939 M88E1000_PHY_PAGE_SELECT, 0x000B);
940 if (ret_val)
941 return ret_val;
942 ret_val = e1000_write_phy_reg(hw,
943 M88E1000_PHY_GEN_CONTROL, 0x8104);
944 if (ret_val)
945 return ret_val;
946
York Sun472d5462013-04-01 11:29:11 -0700947 hw->phy_reset_disable = false;
Roy Zangecbd2072009-08-11 03:48:05 +0800948 }
949 }
Rojhalat Ibrahim8712adf2013-10-07 18:30:39 +0200950#endif
Roy Zangecbd2072009-08-11 03:48:05 +0800951 return E1000_SUCCESS;
952}
wdenk682011f2003-06-03 23:54:09 +0000953
Rojhalat Ibrahim8712adf2013-10-07 18:30:39 +0200954#ifndef CONFIG_E1000_NO_NVM
Roy Zangaa070782009-07-31 13:34:02 +0800955/***************************************************************************
956 *
957 * Obtaining software semaphore bit (SMBI) before resetting PHY.
958 *
959 * hw: Struct containing variables accessed by shared code
960 *
961 * returns: - E1000_ERR_RESET if fail to obtain semaphore.
962 * E1000_SUCCESS at any other case.
963 *
964 ***************************************************************************/
965static int32_t
966e1000_get_software_semaphore(struct e1000_hw *hw)
967{
968 int32_t timeout = hw->eeprom.word_size + 1;
969 uint32_t swsm;
970
971 DEBUGFUNC();
972
973 if (hw->mac_type != e1000_80003es2lan)
974 return E1000_SUCCESS;
975
976 while (timeout) {
977 swsm = E1000_READ_REG(hw, SWSM);
978 /* If SMBI bit cleared, it is now set and we hold
979 * the semaphore */
980 if (!(swsm & E1000_SWSM_SMBI))
981 break;
982 mdelay(1);
983 timeout--;
984 }
985
986 if (!timeout) {
987 DEBUGOUT("Driver can't access device - SMBI bit is set.\n");
988 return -E1000_ERR_RESET;
989 }
990
991 return E1000_SUCCESS;
992}
Rojhalat Ibrahim8712adf2013-10-07 18:30:39 +0200993#endif
Roy Zangaa070782009-07-31 13:34:02 +0800994
995/***************************************************************************
996 * This function clears HW semaphore bits.
997 *
998 * hw: Struct containing variables accessed by shared code
999 *
1000 * returns: - None.
1001 *
1002 ***************************************************************************/
1003static void
1004e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw)
1005{
Rojhalat Ibrahim8712adf2013-10-07 18:30:39 +02001006#ifndef CONFIG_E1000_NO_NVM
Roy Zangaa070782009-07-31 13:34:02 +08001007 uint32_t swsm;
1008
1009 DEBUGFUNC();
1010
1011 if (!hw->eeprom_semaphore_present)
1012 return;
1013
1014 swsm = E1000_READ_REG(hw, SWSM);
1015 if (hw->mac_type == e1000_80003es2lan) {
1016 /* Release both semaphores. */
1017 swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI);
1018 } else
1019 swsm &= ~(E1000_SWSM_SWESMBI);
1020 E1000_WRITE_REG(hw, SWSM, swsm);
Rojhalat Ibrahim8712adf2013-10-07 18:30:39 +02001021#endif
Roy Zangaa070782009-07-31 13:34:02 +08001022}
1023
1024/***************************************************************************
1025 *
1026 * Using the combination of SMBI and SWESMBI semaphore bits when resetting
1027 * adapter or Eeprom access.
1028 *
1029 * hw: Struct containing variables accessed by shared code
1030 *
1031 * returns: - E1000_ERR_EEPROM if fail to access EEPROM.
1032 * E1000_SUCCESS at any other case.
1033 *
1034 ***************************************************************************/
1035static int32_t
1036e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw)
1037{
Rojhalat Ibrahim8712adf2013-10-07 18:30:39 +02001038#ifndef CONFIG_E1000_NO_NVM
Roy Zangaa070782009-07-31 13:34:02 +08001039 int32_t timeout;
1040 uint32_t swsm;
1041
1042 DEBUGFUNC();
1043
1044 if (!hw->eeprom_semaphore_present)
1045 return E1000_SUCCESS;
1046
1047 if (hw->mac_type == e1000_80003es2lan) {
1048 /* Get the SW semaphore. */
1049 if (e1000_get_software_semaphore(hw) != E1000_SUCCESS)
1050 return -E1000_ERR_EEPROM;
1051 }
1052
1053 /* Get the FW semaphore. */
1054 timeout = hw->eeprom.word_size + 1;
1055 while (timeout) {
1056 swsm = E1000_READ_REG(hw, SWSM);
1057 swsm |= E1000_SWSM_SWESMBI;
1058 E1000_WRITE_REG(hw, SWSM, swsm);
1059 /* if we managed to set the bit we got the semaphore. */
1060 swsm = E1000_READ_REG(hw, SWSM);
1061 if (swsm & E1000_SWSM_SWESMBI)
1062 break;
1063
1064 udelay(50);
1065 timeout--;
1066 }
1067
1068 if (!timeout) {
1069 /* Release semaphores */
1070 e1000_put_hw_eeprom_semaphore(hw);
1071 DEBUGOUT("Driver can't access the Eeprom - "
1072 "SWESMBI bit is set.\n");
1073 return -E1000_ERR_EEPROM;
1074 }
Rojhalat Ibrahim8712adf2013-10-07 18:30:39 +02001075#endif
Roy Zangaa070782009-07-31 13:34:02 +08001076 return E1000_SUCCESS;
1077}
1078
Tim Harvey7e2d9912015-05-19 10:01:18 -07001079/* Take ownership of the PHY */
Roy Zangaa070782009-07-31 13:34:02 +08001080static int32_t
1081e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask)
1082{
1083 uint32_t swfw_sync = 0;
1084 uint32_t swmask = mask;
1085 uint32_t fwmask = mask << 16;
1086 int32_t timeout = 200;
1087
1088 DEBUGFUNC();
1089 while (timeout) {
1090 if (e1000_get_hw_eeprom_semaphore(hw))
1091 return -E1000_ERR_SWFW_SYNC;
1092
Tim Harvey3c63dd52015-05-19 10:01:19 -07001093 swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC);
York Sun76f8cdb2014-10-17 13:44:06 -07001094 if (!(swfw_sync & (fwmask | swmask)))
Roy Zangaa070782009-07-31 13:34:02 +08001095 break;
1096
1097 /* firmware currently using resource (fwmask) */
1098 /* or other software thread currently using resource (swmask) */
1099 e1000_put_hw_eeprom_semaphore(hw);
1100 mdelay(5);
1101 timeout--;
1102 }
1103
1104 if (!timeout) {
1105 DEBUGOUT("Driver can't access resource, SW_FW_SYNC timeout.\n");
1106 return -E1000_ERR_SWFW_SYNC;
1107 }
1108
1109 swfw_sync |= swmask;
1110 E1000_WRITE_REG(hw, SW_FW_SYNC, swfw_sync);
1111
1112 e1000_put_hw_eeprom_semaphore(hw);
1113 return E1000_SUCCESS;
1114}
1115
Tim Harvey7e2d9912015-05-19 10:01:18 -07001116static void e1000_swfw_sync_release(struct e1000_hw *hw, uint16_t mask)
1117{
1118 uint32_t swfw_sync = 0;
1119
1120 DEBUGFUNC();
1121 while (e1000_get_hw_eeprom_semaphore(hw))
1122 ; /* Empty */
1123
1124 swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC);
1125 swfw_sync &= ~mask;
1126 E1000_WRITE_REG(hw, SW_FW_SYNC, swfw_sync);
1127
1128 e1000_put_hw_eeprom_semaphore(hw);
1129}
1130
York Sun472d5462013-04-01 11:29:11 -07001131static bool e1000_is_second_port(struct e1000_hw *hw)
Kyle Moffett987b43a2010-09-13 05:52:22 +00001132{
1133 switch (hw->mac_type) {
1134 case e1000_80003es2lan:
1135 case e1000_82546:
1136 case e1000_82571:
1137 if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)
York Sun472d5462013-04-01 11:29:11 -07001138 return true;
Kyle Moffett987b43a2010-09-13 05:52:22 +00001139 /* Fallthrough */
1140 default:
York Sun472d5462013-04-01 11:29:11 -07001141 return false;
Kyle Moffett987b43a2010-09-13 05:52:22 +00001142 }
1143}
1144
Rojhalat Ibrahim8712adf2013-10-07 18:30:39 +02001145#ifndef CONFIG_E1000_NO_NVM
wdenk682011f2003-06-03 23:54:09 +00001146/******************************************************************************
1147 * Reads the adapter's MAC address from the EEPROM and inverts the LSB for the
1148 * second function of dual function devices
1149 *
1150 * nic - Struct containing variables accessed by shared code
1151 *****************************************************************************/
1152static int
Simon Glass5c5e7072015-08-19 09:33:39 -06001153e1000_read_mac_addr(struct e1000_hw *hw, unsigned char enetaddr[6])
wdenk682011f2003-06-03 23:54:09 +00001154{
wdenk682011f2003-06-03 23:54:09 +00001155 uint16_t offset;
1156 uint16_t eeprom_data;
Marek Vasut95186062014-08-08 07:41:39 -07001157 uint32_t reg_data = 0;
wdenk682011f2003-06-03 23:54:09 +00001158 int i;
1159
1160 DEBUGFUNC();
1161
1162 for (i = 0; i < NODE_ADDRESS_SIZE; i += 2) {
1163 offset = i >> 1;
Marek Vasut95186062014-08-08 07:41:39 -07001164 if (hw->mac_type == e1000_igb) {
1165 /* i210 preloads MAC address into RAL/RAH registers */
1166 if (offset == 0)
1167 reg_data = E1000_READ_REG_ARRAY(hw, RA, 0);
1168 else if (offset == 1)
1169 reg_data >>= 16;
1170 else if (offset == 2)
1171 reg_data = E1000_READ_REG_ARRAY(hw, RA, 1);
1172 eeprom_data = reg_data & 0xffff;
1173 } else if (e1000_read_eeprom(hw, offset, 1, &eeprom_data) < 0) {
wdenk682011f2003-06-03 23:54:09 +00001174 DEBUGOUT("EEPROM Read Error\n");
1175 return -E1000_ERR_EEPROM;
1176 }
Simon Glass5c5e7072015-08-19 09:33:39 -06001177 enetaddr[i] = eeprom_data & 0xff;
1178 enetaddr[i + 1] = (eeprom_data >> 8) & 0xff;
wdenk682011f2003-06-03 23:54:09 +00001179 }
Kyle Moffett987b43a2010-09-13 05:52:22 +00001180
1181 /* Invert the last bit if this is the second device */
1182 if (e1000_is_second_port(hw))
Simon Glass5c5e7072015-08-19 09:33:39 -06001183 enetaddr[5] ^= 1;
Kyle Moffett987b43a2010-09-13 05:52:22 +00001184
wdenk682011f2003-06-03 23:54:09 +00001185 return 0;
1186}
Rojhalat Ibrahim8712adf2013-10-07 18:30:39 +02001187#endif
wdenk682011f2003-06-03 23:54:09 +00001188
1189/******************************************************************************
1190 * Initializes receive address filters.
1191 *
wdenk8bde7f72003-06-27 21:31:46 +00001192 * hw - Struct containing variables accessed by shared code
wdenk682011f2003-06-03 23:54:09 +00001193 *
1194 * Places the MAC address in receive address register 0 and clears the rest
1195 * of the receive addresss registers. Clears the multicast table. Assumes
1196 * the receiver is in reset when the routine is called.
1197 *****************************************************************************/
1198static void
Simon Glass5c5e7072015-08-19 09:33:39 -06001199e1000_init_rx_addrs(struct e1000_hw *hw, unsigned char enetaddr[6])
wdenk682011f2003-06-03 23:54:09 +00001200{
wdenk682011f2003-06-03 23:54:09 +00001201 uint32_t i;
1202 uint32_t addr_low;
1203 uint32_t addr_high;
1204
1205 DEBUGFUNC();
1206
1207 /* Setup the receive address. */
1208 DEBUGOUT("Programming MAC Address into RAR[0]\n");
Simon Glass5c5e7072015-08-19 09:33:39 -06001209 addr_low = (enetaddr[0] |
1210 (enetaddr[1] << 8) |
1211 (enetaddr[2] << 16) | (enetaddr[3] << 24));
wdenk682011f2003-06-03 23:54:09 +00001212
Simon Glass5c5e7072015-08-19 09:33:39 -06001213 addr_high = (enetaddr[4] | (enetaddr[5] << 8) | E1000_RAH_AV);
wdenk682011f2003-06-03 23:54:09 +00001214
1215 E1000_WRITE_REG_ARRAY(hw, RA, 0, addr_low);
1216 E1000_WRITE_REG_ARRAY(hw, RA, 1, addr_high);
1217
1218 /* Zero out the other 15 receive addresses. */
1219 DEBUGOUT("Clearing RAR[1-15]\n");
1220 for (i = 1; i < E1000_RAR_ENTRIES; i++) {
1221 E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0);
1222 E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0);
1223 }
1224}
1225
1226/******************************************************************************
1227 * Clears the VLAN filer table
1228 *
1229 * hw - Struct containing variables accessed by shared code
1230 *****************************************************************************/
1231static void
1232e1000_clear_vfta(struct e1000_hw *hw)
1233{
1234 uint32_t offset;
1235
1236 for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++)
1237 E1000_WRITE_REG_ARRAY(hw, VFTA, offset, 0);
1238}
1239
1240/******************************************************************************
1241 * Set the mac type member in the hw struct.
wdenk8bde7f72003-06-27 21:31:46 +00001242 *
wdenk682011f2003-06-03 23:54:09 +00001243 * hw - Struct containing variables accessed by shared code
1244 *****************************************************************************/
Roy Zangaa070782009-07-31 13:34:02 +08001245int32_t
wdenk682011f2003-06-03 23:54:09 +00001246e1000_set_mac_type(struct e1000_hw *hw)
1247{
1248 DEBUGFUNC();
1249
1250 switch (hw->device_id) {
1251 case E1000_DEV_ID_82542:
1252 switch (hw->revision_id) {
1253 case E1000_82542_2_0_REV_ID:
1254 hw->mac_type = e1000_82542_rev2_0;
1255 break;
1256 case E1000_82542_2_1_REV_ID:
1257 hw->mac_type = e1000_82542_rev2_1;
1258 break;
1259 default:
1260 /* Invalid 82542 revision ID */
1261 return -E1000_ERR_MAC_TYPE;
1262 }
1263 break;
1264 case E1000_DEV_ID_82543GC_FIBER:
1265 case E1000_DEV_ID_82543GC_COPPER:
1266 hw->mac_type = e1000_82543;
1267 break;
1268 case E1000_DEV_ID_82544EI_COPPER:
1269 case E1000_DEV_ID_82544EI_FIBER:
1270 case E1000_DEV_ID_82544GC_COPPER:
1271 case E1000_DEV_ID_82544GC_LOM:
1272 hw->mac_type = e1000_82544;
1273 break;
1274 case E1000_DEV_ID_82540EM:
1275 case E1000_DEV_ID_82540EM_LOM:
Roy Zangaa070782009-07-31 13:34:02 +08001276 case E1000_DEV_ID_82540EP:
1277 case E1000_DEV_ID_82540EP_LOM:
1278 case E1000_DEV_ID_82540EP_LP:
wdenk682011f2003-06-03 23:54:09 +00001279 hw->mac_type = e1000_82540;
1280 break;
1281 case E1000_DEV_ID_82545EM_COPPER:
1282 case E1000_DEV_ID_82545EM_FIBER:
1283 hw->mac_type = e1000_82545;
1284 break;
Roy Zangaa070782009-07-31 13:34:02 +08001285 case E1000_DEV_ID_82545GM_COPPER:
1286 case E1000_DEV_ID_82545GM_FIBER:
1287 case E1000_DEV_ID_82545GM_SERDES:
1288 hw->mac_type = e1000_82545_rev_3;
1289 break;
wdenk682011f2003-06-03 23:54:09 +00001290 case E1000_DEV_ID_82546EB_COPPER:
1291 case E1000_DEV_ID_82546EB_FIBER:
Roy Zangaa070782009-07-31 13:34:02 +08001292 case E1000_DEV_ID_82546EB_QUAD_COPPER:
wdenk682011f2003-06-03 23:54:09 +00001293 hw->mac_type = e1000_82546;
1294 break;
Roy Zangaa070782009-07-31 13:34:02 +08001295 case E1000_DEV_ID_82546GB_COPPER:
1296 case E1000_DEV_ID_82546GB_FIBER:
1297 case E1000_DEV_ID_82546GB_SERDES:
1298 case E1000_DEV_ID_82546GB_PCIE:
1299 case E1000_DEV_ID_82546GB_QUAD_COPPER:
1300 case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
1301 hw->mac_type = e1000_82546_rev_3;
1302 break;
1303 case E1000_DEV_ID_82541EI:
1304 case E1000_DEV_ID_82541EI_MOBILE:
1305 case E1000_DEV_ID_82541ER_LOM:
1306 hw->mac_type = e1000_82541;
1307 break;
Andre Schwarzac3315c2008-03-06 16:45:44 +01001308 case E1000_DEV_ID_82541ER:
Roy Zangaa070782009-07-31 13:34:02 +08001309 case E1000_DEV_ID_82541GI:
Wolfgang Grandeggeraa3b8bf2008-05-28 19:55:19 +02001310 case E1000_DEV_ID_82541GI_LF:
Roy Zangaa070782009-07-31 13:34:02 +08001311 case E1000_DEV_ID_82541GI_MOBILE:
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07001312 hw->mac_type = e1000_82541_rev_2;
1313 break;
Roy Zangaa070782009-07-31 13:34:02 +08001314 case E1000_DEV_ID_82547EI:
1315 case E1000_DEV_ID_82547EI_MOBILE:
1316 hw->mac_type = e1000_82547;
1317 break;
1318 case E1000_DEV_ID_82547GI:
1319 hw->mac_type = e1000_82547_rev_2;
1320 break;
1321 case E1000_DEV_ID_82571EB_COPPER:
1322 case E1000_DEV_ID_82571EB_FIBER:
1323 case E1000_DEV_ID_82571EB_SERDES:
1324 case E1000_DEV_ID_82571EB_SERDES_DUAL:
1325 case E1000_DEV_ID_82571EB_SERDES_QUAD:
1326 case E1000_DEV_ID_82571EB_QUAD_COPPER:
1327 case E1000_DEV_ID_82571PT_QUAD_COPPER:
1328 case E1000_DEV_ID_82571EB_QUAD_FIBER:
1329 case E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE:
1330 hw->mac_type = e1000_82571;
1331 break;
1332 case E1000_DEV_ID_82572EI_COPPER:
1333 case E1000_DEV_ID_82572EI_FIBER:
1334 case E1000_DEV_ID_82572EI_SERDES:
1335 case E1000_DEV_ID_82572EI:
1336 hw->mac_type = e1000_82572;
1337 break;
1338 case E1000_DEV_ID_82573E:
1339 case E1000_DEV_ID_82573E_IAMT:
1340 case E1000_DEV_ID_82573L:
1341 hw->mac_type = e1000_82573;
1342 break;
Roy Zang2c2668f2011-01-21 11:29:38 +08001343 case E1000_DEV_ID_82574L:
1344 hw->mac_type = e1000_82574;
1345 break;
Roy Zangaa070782009-07-31 13:34:02 +08001346 case E1000_DEV_ID_80003ES2LAN_COPPER_SPT:
1347 case E1000_DEV_ID_80003ES2LAN_SERDES_SPT:
1348 case E1000_DEV_ID_80003ES2LAN_COPPER_DPT:
1349 case E1000_DEV_ID_80003ES2LAN_SERDES_DPT:
1350 hw->mac_type = e1000_80003es2lan;
1351 break;
1352 case E1000_DEV_ID_ICH8_IGP_M_AMT:
1353 case E1000_DEV_ID_ICH8_IGP_AMT:
1354 case E1000_DEV_ID_ICH8_IGP_C:
1355 case E1000_DEV_ID_ICH8_IFE:
1356 case E1000_DEV_ID_ICH8_IFE_GT:
1357 case E1000_DEV_ID_ICH8_IFE_G:
1358 case E1000_DEV_ID_ICH8_IGP_M:
1359 hw->mac_type = e1000_ich8lan;
1360 break;
Marcel Ziswiler6c499ab2014-09-08 00:03:50 +02001361 case PCI_DEVICE_ID_INTEL_I210_UNPROGRAMMED:
1362 case PCI_DEVICE_ID_INTEL_I211_UNPROGRAMMED:
Marek Vasut95186062014-08-08 07:41:39 -07001363 case PCI_DEVICE_ID_INTEL_I210_COPPER:
Marcel Ziswiler6c499ab2014-09-08 00:03:50 +02001364 case PCI_DEVICE_ID_INTEL_I211_COPPER:
Marek Vasut95186062014-08-08 07:41:39 -07001365 case PCI_DEVICE_ID_INTEL_I210_COPPER_FLASHLESS:
1366 case PCI_DEVICE_ID_INTEL_I210_SERDES:
1367 case PCI_DEVICE_ID_INTEL_I210_SERDES_FLASHLESS:
1368 case PCI_DEVICE_ID_INTEL_I210_1000BASEKX:
1369 hw->mac_type = e1000_igb;
1370 break;
wdenk682011f2003-06-03 23:54:09 +00001371 default:
1372 /* Should never have loaded on this device */
1373 return -E1000_ERR_MAC_TYPE;
1374 }
1375 return E1000_SUCCESS;
1376}
1377
1378/******************************************************************************
1379 * Reset the transmit and receive units; mask and clear all interrupts.
1380 *
1381 * hw - Struct containing variables accessed by shared code
1382 *****************************************************************************/
1383void
1384e1000_reset_hw(struct e1000_hw *hw)
1385{
1386 uint32_t ctrl;
1387 uint32_t ctrl_ext;
wdenk682011f2003-06-03 23:54:09 +00001388 uint32_t manc;
Roy Zang9ea005f2009-08-22 03:49:52 +08001389 uint32_t pba = 0;
Marek Vasut95186062014-08-08 07:41:39 -07001390 uint32_t reg;
wdenk682011f2003-06-03 23:54:09 +00001391
1392 DEBUGFUNC();
1393
Roy Zang9ea005f2009-08-22 03:49:52 +08001394 /* get the correct pba value for both PCI and PCIe*/
1395 if (hw->mac_type < e1000_82571)
1396 pba = E1000_DEFAULT_PCI_PBA;
1397 else
1398 pba = E1000_DEFAULT_PCIE_PBA;
1399
wdenk682011f2003-06-03 23:54:09 +00001400 /* For 82542 (rev 2.0), disable MWI before issuing a device reset */
1401 if (hw->mac_type == e1000_82542_rev2_0) {
1402 DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
Bin Meng81dab9a2016-02-02 05:58:01 -08001403#ifdef CONFIG_DM_ETH
1404 dm_pci_write_config16(hw->pdev, PCI_COMMAND,
1405 hw->pci_cmd_word & ~PCI_COMMAND_INVALIDATE);
1406#else
wdenk682011f2003-06-03 23:54:09 +00001407 pci_write_config_word(hw->pdev, PCI_COMMAND,
Roy Zangaa070782009-07-31 13:34:02 +08001408 hw->pci_cmd_word & ~PCI_COMMAND_INVALIDATE);
Bin Meng81dab9a2016-02-02 05:58:01 -08001409#endif
wdenk682011f2003-06-03 23:54:09 +00001410 }
1411
1412 /* Clear interrupt mask to stop board from generating interrupts */
1413 DEBUGOUT("Masking off all interrupts\n");
Marek Vasut95186062014-08-08 07:41:39 -07001414 if (hw->mac_type == e1000_igb)
1415 E1000_WRITE_REG(hw, I210_IAM, 0);
wdenk682011f2003-06-03 23:54:09 +00001416 E1000_WRITE_REG(hw, IMC, 0xffffffff);
1417
1418 /* Disable the Transmit and Receive units. Then delay to allow
1419 * any pending transactions to complete before we hit the MAC with
1420 * the global reset.
1421 */
1422 E1000_WRITE_REG(hw, RCTL, 0);
1423 E1000_WRITE_REG(hw, TCTL, E1000_TCTL_PSP);
1424 E1000_WRITE_FLUSH(hw);
1425
1426 /* The tbi_compatibility_on Flag must be cleared when Rctl is cleared. */
York Sun472d5462013-04-01 11:29:11 -07001427 hw->tbi_compatibility_on = false;
wdenk682011f2003-06-03 23:54:09 +00001428
1429 /* Delay to allow any outstanding PCI transactions to complete before
1430 * resetting the device
1431 */
1432 mdelay(10);
1433
1434 /* Issue a global reset to the MAC. This will reset the chip's
1435 * transmit, receive, DMA, and link units. It will not effect
1436 * the current PCI configuration. The global reset bit is self-
1437 * clearing, and should clear within a microsecond.
1438 */
1439 DEBUGOUT("Issuing a global reset to MAC\n");
1440 ctrl = E1000_READ_REG(hw, CTRL);
1441
Roy Zangaa070782009-07-31 13:34:02 +08001442 E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_RST));
wdenk682011f2003-06-03 23:54:09 +00001443
1444 /* Force a reload from the EEPROM if necessary */
Marek Vasut95186062014-08-08 07:41:39 -07001445 if (hw->mac_type == e1000_igb) {
1446 mdelay(20);
1447 reg = E1000_READ_REG(hw, STATUS);
1448 if (reg & E1000_STATUS_PF_RST_DONE)
1449 DEBUGOUT("PF OK\n");
1450 reg = E1000_READ_REG(hw, I210_EECD);
1451 if (reg & E1000_EECD_AUTO_RD)
1452 DEBUGOUT("EEC OK\n");
1453 } else if (hw->mac_type < e1000_82540) {
wdenk682011f2003-06-03 23:54:09 +00001454 /* Wait for reset to complete */
1455 udelay(10);
1456 ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
1457 ctrl_ext |= E1000_CTRL_EXT_EE_RST;
1458 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
1459 E1000_WRITE_FLUSH(hw);
1460 /* Wait for EEPROM reload */
1461 mdelay(2);
1462 } else {
1463 /* Wait for EEPROM reload (it happens automatically) */
1464 mdelay(4);
1465 /* Dissable HW ARPs on ASF enabled adapters */
1466 manc = E1000_READ_REG(hw, MANC);
1467 manc &= ~(E1000_MANC_ARP_EN);
1468 E1000_WRITE_REG(hw, MANC, manc);
1469 }
1470
1471 /* Clear interrupt mask to stop board from generating interrupts */
1472 DEBUGOUT("Masking off all interrupts\n");
Marek Vasut95186062014-08-08 07:41:39 -07001473 if (hw->mac_type == e1000_igb)
1474 E1000_WRITE_REG(hw, I210_IAM, 0);
wdenk682011f2003-06-03 23:54:09 +00001475 E1000_WRITE_REG(hw, IMC, 0xffffffff);
1476
1477 /* Clear any pending interrupt events. */
Zang Roy-R6191156b13b12011-11-06 22:22:36 +00001478 E1000_READ_REG(hw, ICR);
wdenk682011f2003-06-03 23:54:09 +00001479
1480 /* If MWI was previously enabled, reenable it. */
1481 if (hw->mac_type == e1000_82542_rev2_0) {
Bin Meng81dab9a2016-02-02 05:58:01 -08001482#ifdef CONFIG_DM_ETH
1483 dm_pci_write_config16(hw->pdev, PCI_COMMAND, hw->pci_cmd_word);
1484#else
wdenk682011f2003-06-03 23:54:09 +00001485 pci_write_config_word(hw->pdev, PCI_COMMAND, hw->pci_cmd_word);
Bin Meng81dab9a2016-02-02 05:58:01 -08001486#endif
wdenk682011f2003-06-03 23:54:09 +00001487 }
Marek Vasut95186062014-08-08 07:41:39 -07001488 if (hw->mac_type != e1000_igb)
1489 E1000_WRITE_REG(hw, PBA, pba);
Roy Zangaa070782009-07-31 13:34:02 +08001490}
1491
1492/******************************************************************************
1493 *
1494 * Initialize a number of hardware-dependent bits
1495 *
1496 * hw: Struct containing variables accessed by shared code
1497 *
1498 * This function contains hardware limitation workarounds for PCI-E adapters
1499 *
1500 *****************************************************************************/
1501static void
1502e1000_initialize_hardware_bits(struct e1000_hw *hw)
1503{
1504 if ((hw->mac_type >= e1000_82571) &&
1505 (!hw->initialize_hw_bits_disable)) {
1506 /* Settings common to all PCI-express silicon */
1507 uint32_t reg_ctrl, reg_ctrl_ext;
1508 uint32_t reg_tarc0, reg_tarc1;
1509 uint32_t reg_tctl;
1510 uint32_t reg_txdctl, reg_txdctl1;
1511
1512 /* link autonegotiation/sync workarounds */
1513 reg_tarc0 = E1000_READ_REG(hw, TARC0);
1514 reg_tarc0 &= ~((1 << 30)|(1 << 29)|(1 << 28)|(1 << 27));
1515
1516 /* Enable not-done TX descriptor counting */
1517 reg_txdctl = E1000_READ_REG(hw, TXDCTL);
1518 reg_txdctl |= E1000_TXDCTL_COUNT_DESC;
1519 E1000_WRITE_REG(hw, TXDCTL, reg_txdctl);
1520
1521 reg_txdctl1 = E1000_READ_REG(hw, TXDCTL1);
1522 reg_txdctl1 |= E1000_TXDCTL_COUNT_DESC;
1523 E1000_WRITE_REG(hw, TXDCTL1, reg_txdctl1);
1524
Marek Vasut95186062014-08-08 07:41:39 -07001525 /* IGB is cool */
1526 if (hw->mac_type == e1000_igb)
1527 return;
1528
Roy Zangaa070782009-07-31 13:34:02 +08001529 switch (hw->mac_type) {
1530 case e1000_82571:
1531 case e1000_82572:
1532 /* Clear PHY TX compatible mode bits */
1533 reg_tarc1 = E1000_READ_REG(hw, TARC1);
1534 reg_tarc1 &= ~((1 << 30)|(1 << 29));
1535
1536 /* link autonegotiation/sync workarounds */
1537 reg_tarc0 |= ((1 << 26)|(1 << 25)|(1 << 24)|(1 << 23));
1538
1539 /* TX ring control fixes */
1540 reg_tarc1 |= ((1 << 26)|(1 << 25)|(1 << 24));
1541
1542 /* Multiple read bit is reversed polarity */
1543 reg_tctl = E1000_READ_REG(hw, TCTL);
1544 if (reg_tctl & E1000_TCTL_MULR)
1545 reg_tarc1 &= ~(1 << 28);
1546 else
1547 reg_tarc1 |= (1 << 28);
1548
1549 E1000_WRITE_REG(hw, TARC1, reg_tarc1);
1550 break;
1551 case e1000_82573:
Roy Zang2c2668f2011-01-21 11:29:38 +08001552 case e1000_82574:
Roy Zangaa070782009-07-31 13:34:02 +08001553 reg_ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
1554 reg_ctrl_ext &= ~(1 << 23);
1555 reg_ctrl_ext |= (1 << 22);
1556
1557 /* TX byte count fix */
1558 reg_ctrl = E1000_READ_REG(hw, CTRL);
1559 reg_ctrl &= ~(1 << 29);
1560
1561 E1000_WRITE_REG(hw, CTRL_EXT, reg_ctrl_ext);
1562 E1000_WRITE_REG(hw, CTRL, reg_ctrl);
1563 break;
1564 case e1000_80003es2lan:
1565 /* improve small packet performace for fiber/serdes */
1566 if ((hw->media_type == e1000_media_type_fiber)
1567 || (hw->media_type ==
1568 e1000_media_type_internal_serdes)) {
1569 reg_tarc0 &= ~(1 << 20);
1570 }
1571
1572 /* Multiple read bit is reversed polarity */
1573 reg_tctl = E1000_READ_REG(hw, TCTL);
1574 reg_tarc1 = E1000_READ_REG(hw, TARC1);
1575 if (reg_tctl & E1000_TCTL_MULR)
1576 reg_tarc1 &= ~(1 << 28);
1577 else
1578 reg_tarc1 |= (1 << 28);
1579
1580 E1000_WRITE_REG(hw, TARC1, reg_tarc1);
1581 break;
1582 case e1000_ich8lan:
1583 /* Reduce concurrent DMA requests to 3 from 4 */
1584 if ((hw->revision_id < 3) ||
1585 ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) &&
1586 (hw->device_id != E1000_DEV_ID_ICH8_IGP_M)))
1587 reg_tarc0 |= ((1 << 29)|(1 << 28));
1588
1589 reg_ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
1590 reg_ctrl_ext |= (1 << 22);
1591 E1000_WRITE_REG(hw, CTRL_EXT, reg_ctrl_ext);
1592
1593 /* workaround TX hang with TSO=on */
1594 reg_tarc0 |= ((1 << 27)|(1 << 26)|(1 << 24)|(1 << 23));
1595
1596 /* Multiple read bit is reversed polarity */
1597 reg_tctl = E1000_READ_REG(hw, TCTL);
1598 reg_tarc1 = E1000_READ_REG(hw, TARC1);
1599 if (reg_tctl & E1000_TCTL_MULR)
1600 reg_tarc1 &= ~(1 << 28);
1601 else
1602 reg_tarc1 |= (1 << 28);
1603
1604 /* workaround TX hang with TSO=on */
1605 reg_tarc1 |= ((1 << 30)|(1 << 26)|(1 << 24));
1606
1607 E1000_WRITE_REG(hw, TARC1, reg_tarc1);
1608 break;
1609 default:
1610 break;
1611 }
1612
1613 E1000_WRITE_REG(hw, TARC0, reg_tarc0);
1614 }
wdenk682011f2003-06-03 23:54:09 +00001615}
1616
1617/******************************************************************************
1618 * Performs basic configuration of the adapter.
1619 *
1620 * hw - Struct containing variables accessed by shared code
wdenk8bde7f72003-06-27 21:31:46 +00001621 *
1622 * Assumes that the controller has previously been reset and is in a
wdenk682011f2003-06-03 23:54:09 +00001623 * post-reset uninitialized state. Initializes the receive address registers,
1624 * multicast table, and VLAN filter table. Calls routines to setup link
1625 * configuration and flow control settings. Clears all on-chip counters. Leaves
1626 * the transmit and receive units disabled and uninitialized.
1627 *****************************************************************************/
1628static int
Simon Glass5c5e7072015-08-19 09:33:39 -06001629e1000_init_hw(struct e1000_hw *hw, unsigned char enetaddr[6])
wdenk682011f2003-06-03 23:54:09 +00001630{
Roy Zangaa070782009-07-31 13:34:02 +08001631 uint32_t ctrl;
wdenk682011f2003-06-03 23:54:09 +00001632 uint32_t i;
1633 int32_t ret_val;
1634 uint16_t pcix_cmd_word;
1635 uint16_t pcix_stat_hi_word;
1636 uint16_t cmd_mmrbc;
1637 uint16_t stat_mmrbc;
Roy Zangaa070782009-07-31 13:34:02 +08001638 uint32_t mta_size;
1639 uint32_t reg_data;
1640 uint32_t ctrl_ext;
wdenk682011f2003-06-03 23:54:09 +00001641 DEBUGFUNC();
Roy Zangaa070782009-07-31 13:34:02 +08001642 /* force full DMA clock frequency for 10/100 on ICH8 A0-B0 */
1643 if ((hw->mac_type == e1000_ich8lan) &&
1644 ((hw->revision_id < 3) ||
1645 ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) &&
1646 (hw->device_id != E1000_DEV_ID_ICH8_IGP_M)))) {
1647 reg_data = E1000_READ_REG(hw, STATUS);
1648 reg_data &= ~0x80000000;
1649 E1000_WRITE_REG(hw, STATUS, reg_data);
wdenk682011f2003-06-03 23:54:09 +00001650 }
Roy Zangaa070782009-07-31 13:34:02 +08001651 /* Do not need initialize Identification LED */
wdenk682011f2003-06-03 23:54:09 +00001652
Roy Zangaa070782009-07-31 13:34:02 +08001653 /* Set the media type and TBI compatibility */
1654 e1000_set_media_type(hw);
1655
1656 /* Must be called after e1000_set_media_type
1657 * because media_type is used */
1658 e1000_initialize_hardware_bits(hw);
wdenk682011f2003-06-03 23:54:09 +00001659
1660 /* Disabling VLAN filtering. */
1661 DEBUGOUT("Initializing the IEEE VLAN\n");
Roy Zangaa070782009-07-31 13:34:02 +08001662 /* VET hardcoded to standard value and VFTA removed in ICH8 LAN */
1663 if (hw->mac_type != e1000_ich8lan) {
1664 if (hw->mac_type < e1000_82545_rev_3)
1665 E1000_WRITE_REG(hw, VET, 0);
1666 e1000_clear_vfta(hw);
1667 }
wdenk682011f2003-06-03 23:54:09 +00001668
1669 /* For 82542 (rev 2.0), disable MWI and put the receiver into reset */
1670 if (hw->mac_type == e1000_82542_rev2_0) {
1671 DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
Bin Meng81dab9a2016-02-02 05:58:01 -08001672#ifdef CONFIG_DM_ETH
1673 dm_pci_write_config16(hw->pdev, PCI_COMMAND,
1674 hw->
1675 pci_cmd_word & ~PCI_COMMAND_INVALIDATE);
1676#else
wdenk682011f2003-06-03 23:54:09 +00001677 pci_write_config_word(hw->pdev, PCI_COMMAND,
1678 hw->
1679 pci_cmd_word & ~PCI_COMMAND_INVALIDATE);
Bin Meng81dab9a2016-02-02 05:58:01 -08001680#endif
wdenk682011f2003-06-03 23:54:09 +00001681 E1000_WRITE_REG(hw, RCTL, E1000_RCTL_RST);
1682 E1000_WRITE_FLUSH(hw);
1683 mdelay(5);
1684 }
1685
1686 /* Setup the receive address. This involves initializing all of the Receive
1687 * Address Registers (RARs 0 - 15).
1688 */
Simon Glass5c5e7072015-08-19 09:33:39 -06001689 e1000_init_rx_addrs(hw, enetaddr);
wdenk682011f2003-06-03 23:54:09 +00001690
1691 /* For 82542 (rev 2.0), take the receiver out of reset and enable MWI */
1692 if (hw->mac_type == e1000_82542_rev2_0) {
1693 E1000_WRITE_REG(hw, RCTL, 0);
1694 E1000_WRITE_FLUSH(hw);
1695 mdelay(1);
Bin Meng81dab9a2016-02-02 05:58:01 -08001696#ifdef CONFIG_DM_ETH
1697 dm_pci_write_config16(hw->pdev, PCI_COMMAND, hw->pci_cmd_word);
1698#else
wdenk682011f2003-06-03 23:54:09 +00001699 pci_write_config_word(hw->pdev, PCI_COMMAND, hw->pci_cmd_word);
Bin Meng81dab9a2016-02-02 05:58:01 -08001700#endif
wdenk682011f2003-06-03 23:54:09 +00001701 }
1702
1703 /* Zero out the Multicast HASH table */
1704 DEBUGOUT("Zeroing the MTA\n");
Roy Zangaa070782009-07-31 13:34:02 +08001705 mta_size = E1000_MC_TBL_SIZE;
1706 if (hw->mac_type == e1000_ich8lan)
1707 mta_size = E1000_MC_TBL_SIZE_ICH8LAN;
1708 for (i = 0; i < mta_size; i++) {
wdenk682011f2003-06-03 23:54:09 +00001709 E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
Roy Zangaa070782009-07-31 13:34:02 +08001710 /* use write flush to prevent Memory Write Block (MWB) from
1711 * occuring when accessing our register space */
1712 E1000_WRITE_FLUSH(hw);
1713 }
Bin Menge97f7fb2015-11-16 01:19:16 -08001714
Roy Zangaa070782009-07-31 13:34:02 +08001715 switch (hw->mac_type) {
1716 case e1000_82545_rev_3:
1717 case e1000_82546_rev_3:
Marek Vasut95186062014-08-08 07:41:39 -07001718 case e1000_igb:
Roy Zangaa070782009-07-31 13:34:02 +08001719 break;
1720 default:
wdenk682011f2003-06-03 23:54:09 +00001721 /* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */
Roy Zangaa070782009-07-31 13:34:02 +08001722 if (hw->bus_type == e1000_bus_type_pcix) {
Bin Meng81dab9a2016-02-02 05:58:01 -08001723#ifdef CONFIG_DM_ETH
1724 dm_pci_read_config16(hw->pdev, PCIX_COMMAND_REGISTER,
1725 &pcix_cmd_word);
1726 dm_pci_read_config16(hw->pdev, PCIX_STATUS_REGISTER_HI,
1727 &pcix_stat_hi_word);
1728#else
wdenk682011f2003-06-03 23:54:09 +00001729 pci_read_config_word(hw->pdev, PCIX_COMMAND_REGISTER,
1730 &pcix_cmd_word);
1731 pci_read_config_word(hw->pdev, PCIX_STATUS_REGISTER_HI,
1732 &pcix_stat_hi_word);
Bin Meng81dab9a2016-02-02 05:58:01 -08001733#endif
wdenk682011f2003-06-03 23:54:09 +00001734 cmd_mmrbc =
1735 (pcix_cmd_word & PCIX_COMMAND_MMRBC_MASK) >>
1736 PCIX_COMMAND_MMRBC_SHIFT;
1737 stat_mmrbc =
1738 (pcix_stat_hi_word & PCIX_STATUS_HI_MMRBC_MASK) >>
1739 PCIX_STATUS_HI_MMRBC_SHIFT;
1740 if (stat_mmrbc == PCIX_STATUS_HI_MMRBC_4K)
1741 stat_mmrbc = PCIX_STATUS_HI_MMRBC_2K;
1742 if (cmd_mmrbc > stat_mmrbc) {
1743 pcix_cmd_word &= ~PCIX_COMMAND_MMRBC_MASK;
1744 pcix_cmd_word |= stat_mmrbc << PCIX_COMMAND_MMRBC_SHIFT;
Bin Meng81dab9a2016-02-02 05:58:01 -08001745#ifdef CONFIG_DM_ETH
1746 dm_pci_write_config16(hw->pdev, PCIX_COMMAND_REGISTER,
1747 pcix_cmd_word);
1748#else
wdenk682011f2003-06-03 23:54:09 +00001749 pci_write_config_word(hw->pdev, PCIX_COMMAND_REGISTER,
1750 pcix_cmd_word);
Bin Meng81dab9a2016-02-02 05:58:01 -08001751#endif
wdenk682011f2003-06-03 23:54:09 +00001752 }
1753 }
Roy Zangaa070782009-07-31 13:34:02 +08001754 break;
1755 }
1756
1757 /* More time needed for PHY to initialize */
1758 if (hw->mac_type == e1000_ich8lan)
1759 mdelay(15);
Marek Vasut95186062014-08-08 07:41:39 -07001760 if (hw->mac_type == e1000_igb)
1761 mdelay(15);
wdenk682011f2003-06-03 23:54:09 +00001762
1763 /* Call a subroutine to configure the link and setup flow control. */
Simon Glass5c5e7072015-08-19 09:33:39 -06001764 ret_val = e1000_setup_link(hw);
wdenk682011f2003-06-03 23:54:09 +00001765
1766 /* Set the transmit descriptor write-back policy */
1767 if (hw->mac_type > e1000_82544) {
1768 ctrl = E1000_READ_REG(hw, TXDCTL);
1769 ctrl =
1770 (ctrl & ~E1000_TXDCTL_WTHRESH) |
1771 E1000_TXDCTL_FULL_TX_DESC_WB;
1772 E1000_WRITE_REG(hw, TXDCTL, ctrl);
1773 }
Roy Zangaa070782009-07-31 13:34:02 +08001774
Ruchika Gupta776e66e2012-04-19 02:27:11 +00001775 /* Set the receive descriptor write back policy */
Ruchika Gupta776e66e2012-04-19 02:27:11 +00001776 if (hw->mac_type >= e1000_82571) {
1777 ctrl = E1000_READ_REG(hw, RXDCTL);
1778 ctrl =
1779 (ctrl & ~E1000_RXDCTL_WTHRESH) |
1780 E1000_RXDCTL_FULL_RX_DESC_WB;
1781 E1000_WRITE_REG(hw, RXDCTL, ctrl);
1782 }
1783
Roy Zangaa070782009-07-31 13:34:02 +08001784 switch (hw->mac_type) {
1785 default:
1786 break;
1787 case e1000_80003es2lan:
1788 /* Enable retransmit on late collisions */
1789 reg_data = E1000_READ_REG(hw, TCTL);
1790 reg_data |= E1000_TCTL_RTLC;
1791 E1000_WRITE_REG(hw, TCTL, reg_data);
1792
1793 /* Configure Gigabit Carry Extend Padding */
1794 reg_data = E1000_READ_REG(hw, TCTL_EXT);
1795 reg_data &= ~E1000_TCTL_EXT_GCEX_MASK;
1796 reg_data |= DEFAULT_80003ES2LAN_TCTL_EXT_GCEX;
1797 E1000_WRITE_REG(hw, TCTL_EXT, reg_data);
1798
1799 /* Configure Transmit Inter-Packet Gap */
1800 reg_data = E1000_READ_REG(hw, TIPG);
1801 reg_data &= ~E1000_TIPG_IPGT_MASK;
1802 reg_data |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000;
1803 E1000_WRITE_REG(hw, TIPG, reg_data);
1804
1805 reg_data = E1000_READ_REG_ARRAY(hw, FFLT, 0x0001);
1806 reg_data &= ~0x00100000;
1807 E1000_WRITE_REG_ARRAY(hw, FFLT, 0x0001, reg_data);
1808 /* Fall through */
1809 case e1000_82571:
1810 case e1000_82572:
1811 case e1000_ich8lan:
1812 ctrl = E1000_READ_REG(hw, TXDCTL1);
1813 ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH)
1814 | E1000_TXDCTL_FULL_TX_DESC_WB;
1815 E1000_WRITE_REG(hw, TXDCTL1, ctrl);
1816 break;
Roy Zang2c2668f2011-01-21 11:29:38 +08001817 case e1000_82573:
1818 case e1000_82574:
1819 reg_data = E1000_READ_REG(hw, GCR);
1820 reg_data |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX;
1821 E1000_WRITE_REG(hw, GCR, reg_data);
Marek Vasut95186062014-08-08 07:41:39 -07001822 case e1000_igb:
1823 break;
Roy Zangaa070782009-07-31 13:34:02 +08001824 }
1825
Roy Zangaa070782009-07-31 13:34:02 +08001826 if (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER ||
1827 hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) {
1828 ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
1829 /* Relaxed ordering must be disabled to avoid a parity
1830 * error crash in a PCI slot. */
1831 ctrl_ext |= E1000_CTRL_EXT_RO_DIS;
1832 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
1833 }
1834
wdenk682011f2003-06-03 23:54:09 +00001835 return ret_val;
1836}
1837
1838/******************************************************************************
1839 * Configures flow control and link settings.
wdenk8bde7f72003-06-27 21:31:46 +00001840 *
wdenk682011f2003-06-03 23:54:09 +00001841 * hw - Struct containing variables accessed by shared code
wdenk8bde7f72003-06-27 21:31:46 +00001842 *
wdenk682011f2003-06-03 23:54:09 +00001843 * Determines which flow control settings to use. Calls the apropriate media-
1844 * specific link configuration function. Configures the flow control settings.
1845 * Assuming the adapter has a valid link partner, a valid link should be
wdenk8bde7f72003-06-27 21:31:46 +00001846 * established. Assumes the hardware has previously been reset and the
wdenk682011f2003-06-03 23:54:09 +00001847 * transmitter and receiver are not enabled.
1848 *****************************************************************************/
1849static int
Simon Glass5c5e7072015-08-19 09:33:39 -06001850e1000_setup_link(struct e1000_hw *hw)
wdenk682011f2003-06-03 23:54:09 +00001851{
wdenk682011f2003-06-03 23:54:09 +00001852 int32_t ret_val;
Rojhalat Ibrahim8712adf2013-10-07 18:30:39 +02001853#ifndef CONFIG_E1000_NO_NVM
1854 uint32_t ctrl_ext;
wdenk682011f2003-06-03 23:54:09 +00001855 uint16_t eeprom_data;
Rojhalat Ibrahim8712adf2013-10-07 18:30:39 +02001856#endif
wdenk682011f2003-06-03 23:54:09 +00001857
1858 DEBUGFUNC();
1859
Roy Zangaa070782009-07-31 13:34:02 +08001860 /* In the case of the phy reset being blocked, we already have a link.
1861 * We do not have to set it up again. */
1862 if (e1000_check_phy_reset_block(hw))
1863 return E1000_SUCCESS;
1864
Rojhalat Ibrahim8712adf2013-10-07 18:30:39 +02001865#ifndef CONFIG_E1000_NO_NVM
wdenk682011f2003-06-03 23:54:09 +00001866 /* Read and store word 0x0F of the EEPROM. This word contains bits
1867 * that determine the hardware's default PAUSE (flow control) mode,
1868 * a bit that determines whether the HW defaults to enabling or
1869 * disabling auto-negotiation, and the direction of the
1870 * SW defined pins. If there is no SW over-ride of the flow
1871 * control setting, then the variable hw->fc will
1872 * be initialized based on a value in the EEPROM.
1873 */
Roy Zangaa070782009-07-31 13:34:02 +08001874 if (e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, 1,
1875 &eeprom_data) < 0) {
wdenk682011f2003-06-03 23:54:09 +00001876 DEBUGOUT("EEPROM Read Error\n");
1877 return -E1000_ERR_EEPROM;
1878 }
Rojhalat Ibrahim8712adf2013-10-07 18:30:39 +02001879#endif
wdenk682011f2003-06-03 23:54:09 +00001880 if (hw->fc == e1000_fc_default) {
Roy Zangaa070782009-07-31 13:34:02 +08001881 switch (hw->mac_type) {
1882 case e1000_ich8lan:
1883 case e1000_82573:
Roy Zang2c2668f2011-01-21 11:29:38 +08001884 case e1000_82574:
Marek Vasut95186062014-08-08 07:41:39 -07001885 case e1000_igb:
wdenk682011f2003-06-03 23:54:09 +00001886 hw->fc = e1000_fc_full;
Roy Zangaa070782009-07-31 13:34:02 +08001887 break;
1888 default:
Rojhalat Ibrahim8712adf2013-10-07 18:30:39 +02001889#ifndef CONFIG_E1000_NO_NVM
Roy Zangaa070782009-07-31 13:34:02 +08001890 ret_val = e1000_read_eeprom(hw,
1891 EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data);
1892 if (ret_val) {
1893 DEBUGOUT("EEPROM Read Error\n");
1894 return -E1000_ERR_EEPROM;
1895 }
Roy Zangaa070782009-07-31 13:34:02 +08001896 if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0)
1897 hw->fc = e1000_fc_none;
1898 else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) ==
1899 EEPROM_WORD0F_ASM_DIR)
1900 hw->fc = e1000_fc_tx_pause;
1901 else
Rojhalat Ibrahim8712adf2013-10-07 18:30:39 +02001902#endif
Roy Zangaa070782009-07-31 13:34:02 +08001903 hw->fc = e1000_fc_full;
1904 break;
1905 }
wdenk682011f2003-06-03 23:54:09 +00001906 }
1907
1908 /* We want to save off the original Flow Control configuration just
1909 * in case we get disconnected and then reconnected into a different
1910 * hub or switch with different Flow Control capabilities.
1911 */
1912 if (hw->mac_type == e1000_82542_rev2_0)
1913 hw->fc &= (~e1000_fc_tx_pause);
1914
1915 if ((hw->mac_type < e1000_82543) && (hw->report_tx_early == 1))
1916 hw->fc &= (~e1000_fc_rx_pause);
1917
1918 hw->original_fc = hw->fc;
1919
1920 DEBUGOUT("After fix-ups FlowControl is now = %x\n", hw->fc);
1921
Rojhalat Ibrahim8712adf2013-10-07 18:30:39 +02001922#ifndef CONFIG_E1000_NO_NVM
wdenk682011f2003-06-03 23:54:09 +00001923 /* Take the 4 bits from EEPROM word 0x0F that determine the initial
1924 * polarity value for the SW controlled pins, and setup the
1925 * Extended Device Control reg with that info.
1926 * This is needed because one of the SW controlled pins is used for
1927 * signal detection. So this should be done before e1000_setup_pcs_link()
1928 * or e1000_phy_setup() is called.
1929 */
1930 if (hw->mac_type == e1000_82543) {
1931 ctrl_ext = ((eeprom_data & EEPROM_WORD0F_SWPDIO_EXT) <<
1932 SWDPIO__EXT_SHIFT);
1933 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
1934 }
Rojhalat Ibrahim8712adf2013-10-07 18:30:39 +02001935#endif
wdenk682011f2003-06-03 23:54:09 +00001936
1937 /* Call the necessary subroutine to configure the link. */
1938 ret_val = (hw->media_type == e1000_media_type_fiber) ?
Simon Glass5c5e7072015-08-19 09:33:39 -06001939 e1000_setup_fiber_link(hw) : e1000_setup_copper_link(hw);
wdenk682011f2003-06-03 23:54:09 +00001940 if (ret_val < 0) {
1941 return ret_val;
1942 }
1943
1944 /* Initialize the flow control address, type, and PAUSE timer
1945 * registers to their default values. This is done even if flow
1946 * control is disabled, because it does not hurt anything to
1947 * initialize these registers.
1948 */
Roy Zangaa070782009-07-31 13:34:02 +08001949 DEBUGOUT("Initializing the Flow Control address, type"
1950 "and timer regs\n");
wdenk682011f2003-06-03 23:54:09 +00001951
Roy Zangaa070782009-07-31 13:34:02 +08001952 /* FCAL/H and FCT are hardcoded to standard values in e1000_ich8lan. */
1953 if (hw->mac_type != e1000_ich8lan) {
1954 E1000_WRITE_REG(hw, FCT, FLOW_CONTROL_TYPE);
1955 E1000_WRITE_REG(hw, FCAH, FLOW_CONTROL_ADDRESS_HIGH);
1956 E1000_WRITE_REG(hw, FCAL, FLOW_CONTROL_ADDRESS_LOW);
1957 }
1958
wdenk682011f2003-06-03 23:54:09 +00001959 E1000_WRITE_REG(hw, FCTTV, hw->fc_pause_time);
1960
1961 /* Set the flow control receive threshold registers. Normally,
1962 * these registers will be set to a default threshold that may be
1963 * adjusted later by the driver's runtime code. However, if the
1964 * ability to transmit pause frames in not enabled, then these
wdenk8bde7f72003-06-27 21:31:46 +00001965 * registers will be set to 0.
wdenk682011f2003-06-03 23:54:09 +00001966 */
1967 if (!(hw->fc & e1000_fc_tx_pause)) {
1968 E1000_WRITE_REG(hw, FCRTL, 0);
1969 E1000_WRITE_REG(hw, FCRTH, 0);
1970 } else {
1971 /* We need to set up the Receive Threshold high and low water marks
1972 * as well as (optionally) enabling the transmission of XON frames.
1973 */
1974 if (hw->fc_send_xon) {
1975 E1000_WRITE_REG(hw, FCRTL,
1976 (hw->fc_low_water | E1000_FCRTL_XONE));
1977 E1000_WRITE_REG(hw, FCRTH, hw->fc_high_water);
1978 } else {
1979 E1000_WRITE_REG(hw, FCRTL, hw->fc_low_water);
1980 E1000_WRITE_REG(hw, FCRTH, hw->fc_high_water);
1981 }
1982 }
1983 return ret_val;
1984}
1985
1986/******************************************************************************
1987 * Sets up link for a fiber based adapter
1988 *
1989 * hw - Struct containing variables accessed by shared code
1990 *
1991 * Manipulates Physical Coding Sublayer functions in order to configure
1992 * link. Assumes the hardware has been previously reset and the transmitter
1993 * and receiver are not enabled.
1994 *****************************************************************************/
1995static int
Simon Glass5c5e7072015-08-19 09:33:39 -06001996e1000_setup_fiber_link(struct e1000_hw *hw)
wdenk682011f2003-06-03 23:54:09 +00001997{
wdenk682011f2003-06-03 23:54:09 +00001998 uint32_t ctrl;
1999 uint32_t status;
2000 uint32_t txcw = 0;
2001 uint32_t i;
2002 uint32_t signal;
2003 int32_t ret_val;
2004
2005 DEBUGFUNC();
wdenk8bde7f72003-06-27 21:31:46 +00002006 /* On adapters with a MAC newer that 82544, SW Defineable pin 1 will be
2007 * set when the optics detect a signal. On older adapters, it will be
wdenk682011f2003-06-03 23:54:09 +00002008 * cleared when there is a signal
2009 */
2010 ctrl = E1000_READ_REG(hw, CTRL);
2011 if ((hw->mac_type > e1000_82544) && !(ctrl & E1000_CTRL_ILOS))
2012 signal = E1000_CTRL_SWDPIN1;
2013 else
2014 signal = 0;
2015
Simon Glass5c5e7072015-08-19 09:33:39 -06002016 printf("signal for %s is %x (ctrl %08x)!!!!\n", hw->name, signal,
wdenk682011f2003-06-03 23:54:09 +00002017 ctrl);
2018 /* Take the link out of reset */
2019 ctrl &= ~(E1000_CTRL_LRST);
2020
2021 e1000_config_collision_dist(hw);
2022
2023 /* Check for a software override of the flow control settings, and setup
2024 * the device accordingly. If auto-negotiation is enabled, then software
2025 * will have to set the "PAUSE" bits to the correct value in the Tranmsit
2026 * Config Word Register (TXCW) and re-start auto-negotiation. However, if
wdenk8bde7f72003-06-27 21:31:46 +00002027 * auto-negotiation is disabled, then software will have to manually
wdenk682011f2003-06-03 23:54:09 +00002028 * configure the two flow control enable bits in the CTRL register.
2029 *
2030 * The possible values of the "fc" parameter are:
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07002031 * 0: Flow control is completely disabled
2032 * 1: Rx flow control is enabled (we can receive pause frames, but
2033 * not send pause frames).
2034 * 2: Tx flow control is enabled (we can send pause frames but we do
2035 * not support receiving pause frames).
2036 * 3: Both Rx and TX flow control (symmetric) are enabled.
wdenk682011f2003-06-03 23:54:09 +00002037 */
2038 switch (hw->fc) {
2039 case e1000_fc_none:
2040 /* Flow control is completely disabled by a software over-ride. */
2041 txcw = (E1000_TXCW_ANE | E1000_TXCW_FD);
2042 break;
2043 case e1000_fc_rx_pause:
wdenk8bde7f72003-06-27 21:31:46 +00002044 /* RX Flow control is enabled and TX Flow control is disabled by a
2045 * software over-ride. Since there really isn't a way to advertise
wdenk682011f2003-06-03 23:54:09 +00002046 * that we are capable of RX Pause ONLY, we will advertise that we
2047 * support both symmetric and asymmetric RX PAUSE. Later, we will
2048 * disable the adapter's ability to send PAUSE frames.
2049 */
2050 txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
2051 break;
2052 case e1000_fc_tx_pause:
wdenk8bde7f72003-06-27 21:31:46 +00002053 /* TX Flow control is enabled, and RX Flow control is disabled, by a
wdenk682011f2003-06-03 23:54:09 +00002054 * software over-ride.
2055 */
2056 txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR);
2057 break;
2058 case e1000_fc_full:
2059 /* Flow control (both RX and TX) is enabled by a software over-ride. */
2060 txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
2061 break;
2062 default:
2063 DEBUGOUT("Flow control param set incorrectly\n");
2064 return -E1000_ERR_CONFIG;
2065 break;
2066 }
2067
2068 /* Since auto-negotiation is enabled, take the link out of reset (the link
2069 * will be in reset, because we previously reset the chip). This will
2070 * restart auto-negotiation. If auto-neogtiation is successful then the
2071 * link-up status bit will be set and the flow control enable bits (RFCE
2072 * and TFCE) will be set according to their negotiated value.
2073 */
2074 DEBUGOUT("Auto-negotiation enabled (%#x)\n", txcw);
2075
2076 E1000_WRITE_REG(hw, TXCW, txcw);
2077 E1000_WRITE_REG(hw, CTRL, ctrl);
2078 E1000_WRITE_FLUSH(hw);
2079
2080 hw->txcw = txcw;
2081 mdelay(1);
2082
2083 /* If we have a signal (the cable is plugged in) then poll for a "Link-Up"
wdenk8bde7f72003-06-27 21:31:46 +00002084 * indication in the Device Status Register. Time-out if a link isn't
2085 * seen in 500 milliseconds seconds (Auto-negotiation should complete in
wdenk682011f2003-06-03 23:54:09 +00002086 * less than 500 milliseconds even if the other end is doing it in SW).
2087 */
2088 if ((E1000_READ_REG(hw, CTRL) & E1000_CTRL_SWDPIN1) == signal) {
2089 DEBUGOUT("Looking for Link\n");
2090 for (i = 0; i < (LINK_UP_TIMEOUT / 10); i++) {
2091 mdelay(10);
2092 status = E1000_READ_REG(hw, STATUS);
2093 if (status & E1000_STATUS_LU)
2094 break;
2095 }
2096 if (i == (LINK_UP_TIMEOUT / 10)) {
wdenk8bde7f72003-06-27 21:31:46 +00002097 /* AutoNeg failed to achieve a link, so we'll call
wdenk682011f2003-06-03 23:54:09 +00002098 * e1000_check_for_link. This routine will force the link up if we
2099 * detect a signal. This will allow us to communicate with
2100 * non-autonegotiating link partners.
2101 */
2102 DEBUGOUT("Never got a valid link from auto-neg!!!\n");
2103 hw->autoneg_failed = 1;
Simon Glass5c5e7072015-08-19 09:33:39 -06002104 ret_val = e1000_check_for_link(hw);
wdenk682011f2003-06-03 23:54:09 +00002105 if (ret_val < 0) {
2106 DEBUGOUT("Error while checking for link\n");
2107 return ret_val;
2108 }
2109 hw->autoneg_failed = 0;
2110 } else {
2111 hw->autoneg_failed = 0;
2112 DEBUGOUT("Valid Link Found\n");
2113 }
2114 } else {
2115 DEBUGOUT("No Signal Detected\n");
2116 return -E1000_ERR_NOLINK;
2117 }
2118 return 0;
2119}
2120
2121/******************************************************************************
Roy Zangaa070782009-07-31 13:34:02 +08002122* Make sure we have a valid PHY and change PHY mode before link setup.
wdenk682011f2003-06-03 23:54:09 +00002123*
2124* hw - Struct containing variables accessed by shared code
2125******************************************************************************/
Roy Zangaa070782009-07-31 13:34:02 +08002126static int32_t
2127e1000_copper_link_preconfig(struct e1000_hw *hw)
wdenk682011f2003-06-03 23:54:09 +00002128{
wdenk682011f2003-06-03 23:54:09 +00002129 uint32_t ctrl;
2130 int32_t ret_val;
wdenk682011f2003-06-03 23:54:09 +00002131 uint16_t phy_data;
2132
2133 DEBUGFUNC();
2134
2135 ctrl = E1000_READ_REG(hw, CTRL);
2136 /* With 82543, we need to force speed and duplex on the MAC equal to what
2137 * the PHY speed and duplex configuration is. In addition, we need to
2138 * perform a hardware reset on the PHY to take it out of reset.
2139 */
2140 if (hw->mac_type > e1000_82543) {
2141 ctrl |= E1000_CTRL_SLU;
2142 ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
2143 E1000_WRITE_REG(hw, CTRL, ctrl);
2144 } else {
Roy Zangaa070782009-07-31 13:34:02 +08002145 ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX
2146 | E1000_CTRL_SLU);
wdenk682011f2003-06-03 23:54:09 +00002147 E1000_WRITE_REG(hw, CTRL, ctrl);
Roy Zangaa070782009-07-31 13:34:02 +08002148 ret_val = e1000_phy_hw_reset(hw);
2149 if (ret_val)
2150 return ret_val;
wdenk682011f2003-06-03 23:54:09 +00002151 }
2152
2153 /* Make sure we have a valid PHY */
2154 ret_val = e1000_detect_gig_phy(hw);
Roy Zangaa070782009-07-31 13:34:02 +08002155 if (ret_val) {
wdenk682011f2003-06-03 23:54:09 +00002156 DEBUGOUT("Error, did not detect valid phy.\n");
2157 return ret_val;
2158 }
Minghuan Lian5abf13e2015-03-19 09:43:51 -07002159 DEBUGOUT("Phy ID = %x\n", hw->phy_id);
wdenk682011f2003-06-03 23:54:09 +00002160
Roy Zangaa070782009-07-31 13:34:02 +08002161 /* Set PHY to class A mode (if necessary) */
2162 ret_val = e1000_set_phy_mode(hw);
2163 if (ret_val)
2164 return ret_val;
Roy Zangaa070782009-07-31 13:34:02 +08002165 if ((hw->mac_type == e1000_82545_rev_3) ||
2166 (hw->mac_type == e1000_82546_rev_3)) {
2167 ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL,
2168 &phy_data);
2169 phy_data |= 0x00000008;
2170 ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL,
2171 phy_data);
wdenk682011f2003-06-03 23:54:09 +00002172 }
Roy Zangaa070782009-07-31 13:34:02 +08002173
2174 if (hw->mac_type <= e1000_82543 ||
2175 hw->mac_type == e1000_82541 || hw->mac_type == e1000_82547 ||
2176 hw->mac_type == e1000_82541_rev_2
2177 || hw->mac_type == e1000_82547_rev_2)
York Sun472d5462013-04-01 11:29:11 -07002178 hw->phy_reset_disable = false;
Roy Zangaa070782009-07-31 13:34:02 +08002179
2180 return E1000_SUCCESS;
2181}
2182
2183/*****************************************************************************
2184 *
2185 * This function sets the lplu state according to the active flag. When
2186 * activating lplu this function also disables smart speed and vise versa.
2187 * lplu will not be activated unless the device autonegotiation advertisment
2188 * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes.
2189 * hw: Struct containing variables accessed by shared code
2190 * active - true to enable lplu false to disable lplu.
2191 *
2192 * returns: - E1000_ERR_PHY if fail to read/write the PHY
2193 * E1000_SUCCESS at any other case.
2194 *
2195 ****************************************************************************/
2196
2197static int32_t
York Sun472d5462013-04-01 11:29:11 -07002198e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active)
Roy Zangaa070782009-07-31 13:34:02 +08002199{
2200 uint32_t phy_ctrl = 0;
2201 int32_t ret_val;
2202 uint16_t phy_data;
2203 DEBUGFUNC();
2204
2205 if (hw->phy_type != e1000_phy_igp && hw->phy_type != e1000_phy_igp_2
2206 && hw->phy_type != e1000_phy_igp_3)
2207 return E1000_SUCCESS;
2208
2209 /* During driver activity LPLU should not be used or it will attain link
2210 * from the lowest speeds starting from 10Mbps. The capability is used
2211 * for Dx transitions and states */
2212 if (hw->mac_type == e1000_82541_rev_2
2213 || hw->mac_type == e1000_82547_rev_2) {
2214 ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO,
2215 &phy_data);
2216 if (ret_val)
2217 return ret_val;
2218 } else if (hw->mac_type == e1000_ich8lan) {
2219 /* MAC writes into PHY register based on the state transition
2220 * and start auto-negotiation. SW driver can overwrite the
2221 * settings in CSR PHY power control E1000_PHY_CTRL register. */
2222 phy_ctrl = E1000_READ_REG(hw, PHY_CTRL);
2223 } else {
2224 ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
2225 &phy_data);
2226 if (ret_val)
2227 return ret_val;
2228 }
2229
2230 if (!active) {
2231 if (hw->mac_type == e1000_82541_rev_2 ||
2232 hw->mac_type == e1000_82547_rev_2) {
2233 phy_data &= ~IGP01E1000_GMII_FLEX_SPD;
2234 ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
2235 phy_data);
2236 if (ret_val)
2237 return ret_val;
2238 } else {
2239 if (hw->mac_type == e1000_ich8lan) {
2240 phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU;
2241 E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl);
2242 } else {
2243 phy_data &= ~IGP02E1000_PM_D3_LPLU;
2244 ret_val = e1000_write_phy_reg(hw,
2245 IGP02E1000_PHY_POWER_MGMT, phy_data);
2246 if (ret_val)
2247 return ret_val;
2248 }
2249 }
2250
2251 /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during
2252 * Dx states where the power conservation is most important. During
2253 * driver activity we should enable SmartSpeed, so performance is
2254 * maintained. */
2255 if (hw->smart_speed == e1000_smart_speed_on) {
2256 ret_val = e1000_read_phy_reg(hw,
2257 IGP01E1000_PHY_PORT_CONFIG, &phy_data);
2258 if (ret_val)
2259 return ret_val;
2260
2261 phy_data |= IGP01E1000_PSCFR_SMART_SPEED;
2262 ret_val = e1000_write_phy_reg(hw,
2263 IGP01E1000_PHY_PORT_CONFIG, phy_data);
2264 if (ret_val)
2265 return ret_val;
2266 } else if (hw->smart_speed == e1000_smart_speed_off) {
2267 ret_val = e1000_read_phy_reg(hw,
2268 IGP01E1000_PHY_PORT_CONFIG, &phy_data);
2269 if (ret_val)
2270 return ret_val;
2271
2272 phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
2273 ret_val = e1000_write_phy_reg(hw,
2274 IGP01E1000_PHY_PORT_CONFIG, phy_data);
2275 if (ret_val)
2276 return ret_val;
2277 }
2278
2279 } else if ((hw->autoneg_advertised == AUTONEG_ADVERTISE_SPEED_DEFAULT)
2280 || (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_ALL) ||
2281 (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_100_ALL)) {
2282
2283 if (hw->mac_type == e1000_82541_rev_2 ||
2284 hw->mac_type == e1000_82547_rev_2) {
2285 phy_data |= IGP01E1000_GMII_FLEX_SPD;
2286 ret_val = e1000_write_phy_reg(hw,
2287 IGP01E1000_GMII_FIFO, phy_data);
2288 if (ret_val)
2289 return ret_val;
2290 } else {
2291 if (hw->mac_type == e1000_ich8lan) {
2292 phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU;
2293 E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl);
2294 } else {
2295 phy_data |= IGP02E1000_PM_D3_LPLU;
2296 ret_val = e1000_write_phy_reg(hw,
2297 IGP02E1000_PHY_POWER_MGMT, phy_data);
2298 if (ret_val)
2299 return ret_val;
2300 }
2301 }
2302
2303 /* When LPLU is enabled we should disable SmartSpeed */
2304 ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
2305 &phy_data);
2306 if (ret_val)
2307 return ret_val;
2308
2309 phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
2310 ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
2311 phy_data);
2312 if (ret_val)
2313 return ret_val;
2314 }
2315 return E1000_SUCCESS;
2316}
2317
2318/*****************************************************************************
2319 *
2320 * This function sets the lplu d0 state according to the active flag. When
2321 * activating lplu this function also disables smart speed and vise versa.
2322 * lplu will not be activated unless the device autonegotiation advertisment
2323 * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes.
2324 * hw: Struct containing variables accessed by shared code
2325 * active - true to enable lplu false to disable lplu.
2326 *
2327 * returns: - E1000_ERR_PHY if fail to read/write the PHY
2328 * E1000_SUCCESS at any other case.
2329 *
2330 ****************************************************************************/
2331
2332static int32_t
York Sun472d5462013-04-01 11:29:11 -07002333e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active)
Roy Zangaa070782009-07-31 13:34:02 +08002334{
2335 uint32_t phy_ctrl = 0;
2336 int32_t ret_val;
2337 uint16_t phy_data;
2338 DEBUGFUNC();
2339
2340 if (hw->mac_type <= e1000_82547_rev_2)
2341 return E1000_SUCCESS;
2342
2343 if (hw->mac_type == e1000_ich8lan) {
2344 phy_ctrl = E1000_READ_REG(hw, PHY_CTRL);
Marek Vasut95186062014-08-08 07:41:39 -07002345 } else if (hw->mac_type == e1000_igb) {
2346 phy_ctrl = E1000_READ_REG(hw, I210_PHY_CTRL);
Roy Zangaa070782009-07-31 13:34:02 +08002347 } else {
2348 ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
2349 &phy_data);
2350 if (ret_val)
2351 return ret_val;
2352 }
2353
2354 if (!active) {
2355 if (hw->mac_type == e1000_ich8lan) {
2356 phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU;
2357 E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl);
Marek Vasut95186062014-08-08 07:41:39 -07002358 } else if (hw->mac_type == e1000_igb) {
2359 phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU;
2360 E1000_WRITE_REG(hw, I210_PHY_CTRL, phy_ctrl);
Roy Zangaa070782009-07-31 13:34:02 +08002361 } else {
2362 phy_data &= ~IGP02E1000_PM_D0_LPLU;
2363 ret_val = e1000_write_phy_reg(hw,
2364 IGP02E1000_PHY_POWER_MGMT, phy_data);
2365 if (ret_val)
2366 return ret_val;
2367 }
2368
Marek Vasut95186062014-08-08 07:41:39 -07002369 if (hw->mac_type == e1000_igb)
2370 return E1000_SUCCESS;
2371
Roy Zangaa070782009-07-31 13:34:02 +08002372 /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during
2373 * Dx states where the power conservation is most important. During
2374 * driver activity we should enable SmartSpeed, so performance is
2375 * maintained. */
2376 if (hw->smart_speed == e1000_smart_speed_on) {
2377 ret_val = e1000_read_phy_reg(hw,
2378 IGP01E1000_PHY_PORT_CONFIG, &phy_data);
2379 if (ret_val)
2380 return ret_val;
2381
2382 phy_data |= IGP01E1000_PSCFR_SMART_SPEED;
2383 ret_val = e1000_write_phy_reg(hw,
2384 IGP01E1000_PHY_PORT_CONFIG, phy_data);
2385 if (ret_val)
2386 return ret_val;
2387 } else if (hw->smart_speed == e1000_smart_speed_off) {
2388 ret_val = e1000_read_phy_reg(hw,
2389 IGP01E1000_PHY_PORT_CONFIG, &phy_data);
2390 if (ret_val)
2391 return ret_val;
2392
2393 phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
2394 ret_val = e1000_write_phy_reg(hw,
2395 IGP01E1000_PHY_PORT_CONFIG, phy_data);
2396 if (ret_val)
2397 return ret_val;
2398 }
2399
2400
2401 } else {
2402
2403 if (hw->mac_type == e1000_ich8lan) {
2404 phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU;
2405 E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl);
Marek Vasut95186062014-08-08 07:41:39 -07002406 } else if (hw->mac_type == e1000_igb) {
2407 phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU;
2408 E1000_WRITE_REG(hw, I210_PHY_CTRL, phy_ctrl);
Roy Zangaa070782009-07-31 13:34:02 +08002409 } else {
2410 phy_data |= IGP02E1000_PM_D0_LPLU;
2411 ret_val = e1000_write_phy_reg(hw,
2412 IGP02E1000_PHY_POWER_MGMT, phy_data);
2413 if (ret_val)
2414 return ret_val;
2415 }
2416
Marek Vasut95186062014-08-08 07:41:39 -07002417 if (hw->mac_type == e1000_igb)
2418 return E1000_SUCCESS;
2419
Roy Zangaa070782009-07-31 13:34:02 +08002420 /* When LPLU is enabled we should disable SmartSpeed */
2421 ret_val = e1000_read_phy_reg(hw,
2422 IGP01E1000_PHY_PORT_CONFIG, &phy_data);
2423 if (ret_val)
2424 return ret_val;
2425
2426 phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
2427 ret_val = e1000_write_phy_reg(hw,
2428 IGP01E1000_PHY_PORT_CONFIG, phy_data);
2429 if (ret_val)
2430 return ret_val;
2431
2432 }
2433 return E1000_SUCCESS;
2434}
2435
2436/********************************************************************
2437* Copper link setup for e1000_phy_igp series.
2438*
2439* hw - Struct containing variables accessed by shared code
2440*********************************************************************/
2441static int32_t
2442e1000_copper_link_igp_setup(struct e1000_hw *hw)
2443{
2444 uint32_t led_ctrl;
2445 int32_t ret_val;
2446 uint16_t phy_data;
2447
Timur Tabif81ecb52009-08-17 15:55:38 -05002448 DEBUGFUNC();
Roy Zangaa070782009-07-31 13:34:02 +08002449
2450 if (hw->phy_reset_disable)
2451 return E1000_SUCCESS;
2452
2453 ret_val = e1000_phy_reset(hw);
2454 if (ret_val) {
2455 DEBUGOUT("Error Resetting the PHY\n");
2456 return ret_val;
2457 }
2458
2459 /* Wait 15ms for MAC to configure PHY from eeprom settings */
2460 mdelay(15);
2461 if (hw->mac_type != e1000_ich8lan) {
2462 /* Configure activity LED after PHY reset */
2463 led_ctrl = E1000_READ_REG(hw, LEDCTL);
2464 led_ctrl &= IGP_ACTIVITY_LED_MASK;
2465 led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
2466 E1000_WRITE_REG(hw, LEDCTL, led_ctrl);
2467 }
2468
2469 /* The NVM settings will configure LPLU in D3 for IGP2 and IGP3 PHYs */
2470 if (hw->phy_type == e1000_phy_igp) {
2471 /* disable lplu d3 during driver init */
York Sun472d5462013-04-01 11:29:11 -07002472 ret_val = e1000_set_d3_lplu_state(hw, false);
Roy Zangaa070782009-07-31 13:34:02 +08002473 if (ret_val) {
2474 DEBUGOUT("Error Disabling LPLU D3\n");
2475 return ret_val;
2476 }
2477 }
2478
2479 /* disable lplu d0 during driver init */
York Sun472d5462013-04-01 11:29:11 -07002480 ret_val = e1000_set_d0_lplu_state(hw, false);
Roy Zangaa070782009-07-31 13:34:02 +08002481 if (ret_val) {
2482 DEBUGOUT("Error Disabling LPLU D0\n");
2483 return ret_val;
2484 }
2485 /* Configure mdi-mdix settings */
2486 ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data);
2487 if (ret_val)
2488 return ret_val;
2489
2490 if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
2491 hw->dsp_config_state = e1000_dsp_config_disabled;
2492 /* Force MDI for earlier revs of the IGP PHY */
2493 phy_data &= ~(IGP01E1000_PSCR_AUTO_MDIX
2494 | IGP01E1000_PSCR_FORCE_MDI_MDIX);
2495 hw->mdix = 1;
2496
2497 } else {
2498 hw->dsp_config_state = e1000_dsp_config_enabled;
2499 phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX;
2500
2501 switch (hw->mdix) {
2502 case 1:
2503 phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
2504 break;
2505 case 2:
2506 phy_data |= IGP01E1000_PSCR_FORCE_MDI_MDIX;
2507 break;
2508 case 0:
2509 default:
2510 phy_data |= IGP01E1000_PSCR_AUTO_MDIX;
2511 break;
2512 }
2513 }
2514 ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data);
2515 if (ret_val)
2516 return ret_val;
2517
2518 /* set auto-master slave resolution settings */
2519 if (hw->autoneg) {
2520 e1000_ms_type phy_ms_setting = hw->master_slave;
2521
2522 if (hw->ffe_config_state == e1000_ffe_config_active)
2523 hw->ffe_config_state = e1000_ffe_config_enabled;
2524
2525 if (hw->dsp_config_state == e1000_dsp_config_activated)
2526 hw->dsp_config_state = e1000_dsp_config_enabled;
2527
2528 /* when autonegotiation advertisment is only 1000Mbps then we
2529 * should disable SmartSpeed and enable Auto MasterSlave
2530 * resolution as hardware default. */
2531 if (hw->autoneg_advertised == ADVERTISE_1000_FULL) {
2532 /* Disable SmartSpeed */
2533 ret_val = e1000_read_phy_reg(hw,
2534 IGP01E1000_PHY_PORT_CONFIG, &phy_data);
2535 if (ret_val)
2536 return ret_val;
2537 phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
2538 ret_val = e1000_write_phy_reg(hw,
2539 IGP01E1000_PHY_PORT_CONFIG, phy_data);
2540 if (ret_val)
2541 return ret_val;
2542 /* Set auto Master/Slave resolution process */
2543 ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL,
2544 &phy_data);
2545 if (ret_val)
2546 return ret_val;
2547 phy_data &= ~CR_1000T_MS_ENABLE;
2548 ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL,
2549 phy_data);
2550 if (ret_val)
2551 return ret_val;
2552 }
2553
2554 ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data);
2555 if (ret_val)
2556 return ret_val;
2557
2558 /* load defaults for future use */
2559 hw->original_master_slave = (phy_data & CR_1000T_MS_ENABLE) ?
2560 ((phy_data & CR_1000T_MS_VALUE) ?
2561 e1000_ms_force_master :
2562 e1000_ms_force_slave) :
2563 e1000_ms_auto;
2564
2565 switch (phy_ms_setting) {
2566 case e1000_ms_force_master:
2567 phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE);
2568 break;
2569 case e1000_ms_force_slave:
2570 phy_data |= CR_1000T_MS_ENABLE;
2571 phy_data &= ~(CR_1000T_MS_VALUE);
2572 break;
2573 case e1000_ms_auto:
2574 phy_data &= ~CR_1000T_MS_ENABLE;
2575 default:
2576 break;
2577 }
2578 ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
2579 if (ret_val)
2580 return ret_val;
2581 }
2582
2583 return E1000_SUCCESS;
2584}
2585
2586/*****************************************************************************
2587 * This function checks the mode of the firmware.
2588 *
York Sun472d5462013-04-01 11:29:11 -07002589 * returns - true when the mode is IAMT or false.
Roy Zangaa070782009-07-31 13:34:02 +08002590 ****************************************************************************/
York Sun472d5462013-04-01 11:29:11 -07002591bool
Roy Zangaa070782009-07-31 13:34:02 +08002592e1000_check_mng_mode(struct e1000_hw *hw)
2593{
2594 uint32_t fwsm;
2595 DEBUGFUNC();
2596
2597 fwsm = E1000_READ_REG(hw, FWSM);
2598
2599 if (hw->mac_type == e1000_ich8lan) {
2600 if ((fwsm & E1000_FWSM_MODE_MASK) ==
2601 (E1000_MNG_ICH_IAMT_MODE << E1000_FWSM_MODE_SHIFT))
York Sun472d5462013-04-01 11:29:11 -07002602 return true;
Roy Zangaa070782009-07-31 13:34:02 +08002603 } else if ((fwsm & E1000_FWSM_MODE_MASK) ==
2604 (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT))
York Sun472d5462013-04-01 11:29:11 -07002605 return true;
Roy Zangaa070782009-07-31 13:34:02 +08002606
York Sun472d5462013-04-01 11:29:11 -07002607 return false;
Roy Zangaa070782009-07-31 13:34:02 +08002608}
2609
2610static int32_t
2611e1000_write_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t data)
2612{
Kyle Moffett987b43a2010-09-13 05:52:22 +00002613 uint16_t swfw = E1000_SWFW_PHY0_SM;
Roy Zangaa070782009-07-31 13:34:02 +08002614 uint32_t reg_val;
Roy Zangaa070782009-07-31 13:34:02 +08002615 DEBUGFUNC();
2616
Kyle Moffett987b43a2010-09-13 05:52:22 +00002617 if (e1000_is_second_port(hw))
Roy Zangaa070782009-07-31 13:34:02 +08002618 swfw = E1000_SWFW_PHY1_SM;
Kyle Moffett987b43a2010-09-13 05:52:22 +00002619
Roy Zangaa070782009-07-31 13:34:02 +08002620 if (e1000_swfw_sync_acquire(hw, swfw))
2621 return -E1000_ERR_SWFW_SYNC;
2622
2623 reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT)
2624 & E1000_KUMCTRLSTA_OFFSET) | data;
2625 E1000_WRITE_REG(hw, KUMCTRLSTA, reg_val);
2626 udelay(2);
2627
2628 return E1000_SUCCESS;
2629}
2630
2631static int32_t
2632e1000_read_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t *data)
2633{
Kyle Moffett987b43a2010-09-13 05:52:22 +00002634 uint16_t swfw = E1000_SWFW_PHY0_SM;
Roy Zangaa070782009-07-31 13:34:02 +08002635 uint32_t reg_val;
Roy Zangaa070782009-07-31 13:34:02 +08002636 DEBUGFUNC();
2637
Kyle Moffett987b43a2010-09-13 05:52:22 +00002638 if (e1000_is_second_port(hw))
Roy Zangaa070782009-07-31 13:34:02 +08002639 swfw = E1000_SWFW_PHY1_SM;
Kyle Moffett987b43a2010-09-13 05:52:22 +00002640
Marek Vasut95186062014-08-08 07:41:39 -07002641 if (e1000_swfw_sync_acquire(hw, swfw)) {
2642 debug("%s[%i]\n", __func__, __LINE__);
Roy Zangaa070782009-07-31 13:34:02 +08002643 return -E1000_ERR_SWFW_SYNC;
Marek Vasut95186062014-08-08 07:41:39 -07002644 }
Roy Zangaa070782009-07-31 13:34:02 +08002645
2646 /* Write register address */
2647 reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) &
2648 E1000_KUMCTRLSTA_OFFSET) | E1000_KUMCTRLSTA_REN;
2649 E1000_WRITE_REG(hw, KUMCTRLSTA, reg_val);
2650 udelay(2);
2651
2652 /* Read the data returned */
2653 reg_val = E1000_READ_REG(hw, KUMCTRLSTA);
2654 *data = (uint16_t)reg_val;
2655
2656 return E1000_SUCCESS;
2657}
2658
2659/********************************************************************
2660* Copper link setup for e1000_phy_gg82563 series.
2661*
2662* hw - Struct containing variables accessed by shared code
2663*********************************************************************/
2664static int32_t
2665e1000_copper_link_ggp_setup(struct e1000_hw *hw)
2666{
2667 int32_t ret_val;
2668 uint16_t phy_data;
2669 uint32_t reg_data;
2670
2671 DEBUGFUNC();
2672
2673 if (!hw->phy_reset_disable) {
2674 /* Enable CRS on TX for half-duplex operation. */
2675 ret_val = e1000_read_phy_reg(hw,
2676 GG82563_PHY_MAC_SPEC_CTRL, &phy_data);
2677 if (ret_val)
2678 return ret_val;
2679
2680 phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
2681 /* Use 25MHz for both link down and 1000BASE-T for Tx clock */
2682 phy_data |= GG82563_MSCR_TX_CLK_1000MBPS_25MHZ;
2683
2684 ret_val = e1000_write_phy_reg(hw,
2685 GG82563_PHY_MAC_SPEC_CTRL, phy_data);
2686 if (ret_val)
2687 return ret_val;
2688
2689 /* Options:
2690 * MDI/MDI-X = 0 (default)
2691 * 0 - Auto for all speeds
2692 * 1 - MDI mode
2693 * 2 - MDI-X mode
2694 * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
2695 */
2696 ret_val = e1000_read_phy_reg(hw,
2697 GG82563_PHY_SPEC_CTRL, &phy_data);
2698 if (ret_val)
2699 return ret_val;
2700
2701 phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK;
2702
2703 switch (hw->mdix) {
2704 case 1:
2705 phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDI;
2706 break;
2707 case 2:
2708 phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDIX;
2709 break;
2710 case 0:
2711 default:
2712 phy_data |= GG82563_PSCR_CROSSOVER_MODE_AUTO;
2713 break;
2714 }
2715
2716 /* Options:
2717 * disable_polarity_correction = 0 (default)
2718 * Automatic Correction for Reversed Cable Polarity
2719 * 0 - Disabled
2720 * 1 - Enabled
2721 */
2722 phy_data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
2723 ret_val = e1000_write_phy_reg(hw,
2724 GG82563_PHY_SPEC_CTRL, phy_data);
2725
2726 if (ret_val)
2727 return ret_val;
2728
2729 /* SW Reset the PHY so all changes take effect */
2730 ret_val = e1000_phy_reset(hw);
2731 if (ret_val) {
2732 DEBUGOUT("Error Resetting the PHY\n");
2733 return ret_val;
2734 }
2735 } /* phy_reset_disable */
2736
2737 if (hw->mac_type == e1000_80003es2lan) {
2738 /* Bypass RX and TX FIFO's */
2739 ret_val = e1000_write_kmrn_reg(hw,
2740 E1000_KUMCTRLSTA_OFFSET_FIFO_CTRL,
2741 E1000_KUMCTRLSTA_FIFO_CTRL_RX_BYPASS
2742 | E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS);
2743 if (ret_val)
2744 return ret_val;
2745
2746 ret_val = e1000_read_phy_reg(hw,
2747 GG82563_PHY_SPEC_CTRL_2, &phy_data);
2748 if (ret_val)
2749 return ret_val;
2750
2751 phy_data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG;
2752 ret_val = e1000_write_phy_reg(hw,
2753 GG82563_PHY_SPEC_CTRL_2, phy_data);
2754
2755 if (ret_val)
2756 return ret_val;
2757
2758 reg_data = E1000_READ_REG(hw, CTRL_EXT);
2759 reg_data &= ~(E1000_CTRL_EXT_LINK_MODE_MASK);
2760 E1000_WRITE_REG(hw, CTRL_EXT, reg_data);
2761
2762 ret_val = e1000_read_phy_reg(hw,
2763 GG82563_PHY_PWR_MGMT_CTRL, &phy_data);
2764 if (ret_val)
2765 return ret_val;
2766
2767 /* Do not init these registers when the HW is in IAMT mode, since the
2768 * firmware will have already initialized them. We only initialize
2769 * them if the HW is not in IAMT mode.
2770 */
York Sun472d5462013-04-01 11:29:11 -07002771 if (e1000_check_mng_mode(hw) == false) {
Roy Zangaa070782009-07-31 13:34:02 +08002772 /* Enable Electrical Idle on the PHY */
2773 phy_data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE;
2774 ret_val = e1000_write_phy_reg(hw,
2775 GG82563_PHY_PWR_MGMT_CTRL, phy_data);
2776 if (ret_val)
2777 return ret_val;
2778
2779 ret_val = e1000_read_phy_reg(hw,
2780 GG82563_PHY_KMRN_MODE_CTRL, &phy_data);
2781 if (ret_val)
2782 return ret_val;
2783
2784 phy_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
2785 ret_val = e1000_write_phy_reg(hw,
2786 GG82563_PHY_KMRN_MODE_CTRL, phy_data);
2787
2788 if (ret_val)
2789 return ret_val;
2790 }
2791
2792 /* Workaround: Disable padding in Kumeran interface in the MAC
2793 * and in the PHY to avoid CRC errors.
2794 */
2795 ret_val = e1000_read_phy_reg(hw,
2796 GG82563_PHY_INBAND_CTRL, &phy_data);
2797 if (ret_val)
2798 return ret_val;
2799 phy_data |= GG82563_ICR_DIS_PADDING;
2800 ret_val = e1000_write_phy_reg(hw,
2801 GG82563_PHY_INBAND_CTRL, phy_data);
2802 if (ret_val)
2803 return ret_val;
2804 }
2805 return E1000_SUCCESS;
2806}
2807
2808/********************************************************************
2809* Copper link setup for e1000_phy_m88 series.
2810*
2811* hw - Struct containing variables accessed by shared code
2812*********************************************************************/
2813static int32_t
2814e1000_copper_link_mgp_setup(struct e1000_hw *hw)
2815{
2816 int32_t ret_val;
2817 uint16_t phy_data;
2818
2819 DEBUGFUNC();
2820
2821 if (hw->phy_reset_disable)
2822 return E1000_SUCCESS;
2823
2824 /* Enable CRS on TX. This must be set for half-duplex operation. */
2825 ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
2826 if (ret_val)
2827 return ret_val;
2828
wdenk682011f2003-06-03 23:54:09 +00002829 phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
2830
wdenk682011f2003-06-03 23:54:09 +00002831 /* Options:
2832 * MDI/MDI-X = 0 (default)
2833 * 0 - Auto for all speeds
2834 * 1 - MDI mode
2835 * 2 - MDI-X mode
2836 * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
2837 */
2838 phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
Roy Zangaa070782009-07-31 13:34:02 +08002839
wdenk682011f2003-06-03 23:54:09 +00002840 switch (hw->mdix) {
2841 case 1:
2842 phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE;
2843 break;
2844 case 2:
2845 phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE;
2846 break;
2847 case 3:
2848 phy_data |= M88E1000_PSCR_AUTO_X_1000T;
2849 break;
2850 case 0:
2851 default:
2852 phy_data |= M88E1000_PSCR_AUTO_X_MODE;
2853 break;
2854 }
wdenk682011f2003-06-03 23:54:09 +00002855
wdenk682011f2003-06-03 23:54:09 +00002856 /* Options:
2857 * disable_polarity_correction = 0 (default)
Roy Zangaa070782009-07-31 13:34:02 +08002858 * Automatic Correction for Reversed Cable Polarity
wdenk682011f2003-06-03 23:54:09 +00002859 * 0 - Disabled
2860 * 1 - Enabled
2861 */
2862 phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
Roy Zangaa070782009-07-31 13:34:02 +08002863 ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
2864 if (ret_val)
2865 return ret_val;
wdenk682011f2003-06-03 23:54:09 +00002866
Roy Zangaa070782009-07-31 13:34:02 +08002867 if (hw->phy_revision < M88E1011_I_REV_4) {
2868 /* Force TX_CLK in the Extended PHY Specific Control Register
2869 * to 25MHz clock.
2870 */
2871 ret_val = e1000_read_phy_reg(hw,
2872 M88E1000_EXT_PHY_SPEC_CTRL, &phy_data);
2873 if (ret_val)
2874 return ret_val;
2875
2876 phy_data |= M88E1000_EPSCR_TX_CLK_25;
2877
2878 if ((hw->phy_revision == E1000_REVISION_2) &&
2879 (hw->phy_id == M88E1111_I_PHY_ID)) {
2880 /* Vidalia Phy, set the downshift counter to 5x */
2881 phy_data &= ~(M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK);
2882 phy_data |= M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X;
2883 ret_val = e1000_write_phy_reg(hw,
2884 M88E1000_EXT_PHY_SPEC_CTRL, phy_data);
2885 if (ret_val)
2886 return ret_val;
2887 } else {
2888 /* Configure Master and Slave downshift values */
2889 phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK
2890 | M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK);
2891 phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X
2892 | M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X);
2893 ret_val = e1000_write_phy_reg(hw,
2894 M88E1000_EXT_PHY_SPEC_CTRL, phy_data);
2895 if (ret_val)
2896 return ret_val;
2897 }
wdenk682011f2003-06-03 23:54:09 +00002898 }
2899
2900 /* SW Reset the PHY so all changes take effect */
2901 ret_val = e1000_phy_reset(hw);
Roy Zangaa070782009-07-31 13:34:02 +08002902 if (ret_val) {
wdenk682011f2003-06-03 23:54:09 +00002903 DEBUGOUT("Error Resetting the PHY\n");
2904 return ret_val;
2905 }
2906
Roy Zangaa070782009-07-31 13:34:02 +08002907 return E1000_SUCCESS;
2908}
wdenk682011f2003-06-03 23:54:09 +00002909
Roy Zangaa070782009-07-31 13:34:02 +08002910/********************************************************************
2911* Setup auto-negotiation and flow control advertisements,
2912* and then perform auto-negotiation.
2913*
2914* hw - Struct containing variables accessed by shared code
2915*********************************************************************/
2916static int32_t
2917e1000_copper_link_autoneg(struct e1000_hw *hw)
2918{
2919 int32_t ret_val;
2920 uint16_t phy_data;
2921
2922 DEBUGFUNC();
2923
wdenk682011f2003-06-03 23:54:09 +00002924 /* Perform some bounds checking on the hw->autoneg_advertised
2925 * parameter. If this variable is zero, then set it to the default.
2926 */
2927 hw->autoneg_advertised &= AUTONEG_ADVERTISE_SPEED_DEFAULT;
2928
2929 /* If autoneg_advertised is zero, we assume it was not defaulted
2930 * by the calling code so we set to advertise full capability.
2931 */
2932 if (hw->autoneg_advertised == 0)
2933 hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT;
2934
Roy Zangaa070782009-07-31 13:34:02 +08002935 /* IFE phy only supports 10/100 */
2936 if (hw->phy_type == e1000_phy_ife)
2937 hw->autoneg_advertised &= AUTONEG_ADVERTISE_10_100_ALL;
2938
wdenk682011f2003-06-03 23:54:09 +00002939 DEBUGOUT("Reconfiguring auto-neg advertisement params\n");
2940 ret_val = e1000_phy_setup_autoneg(hw);
Roy Zangaa070782009-07-31 13:34:02 +08002941 if (ret_val) {
wdenk682011f2003-06-03 23:54:09 +00002942 DEBUGOUT("Error Setting up Auto-Negotiation\n");
2943 return ret_val;
2944 }
2945 DEBUGOUT("Restarting Auto-Neg\n");
2946
2947 /* Restart auto-negotiation by setting the Auto Neg Enable bit and
2948 * the Auto Neg Restart bit in the PHY control register.
2949 */
Roy Zangaa070782009-07-31 13:34:02 +08002950 ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
2951 if (ret_val)
2952 return ret_val;
2953
wdenk682011f2003-06-03 23:54:09 +00002954 phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
Roy Zangaa070782009-07-31 13:34:02 +08002955 ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
2956 if (ret_val)
2957 return ret_val;
2958
wdenk682011f2003-06-03 23:54:09 +00002959 /* Does the user want to wait for Auto-Neg to complete here, or
2960 * check at a later time (for example, callback routine).
2961 */
Roy Zangaa070782009-07-31 13:34:02 +08002962 /* If we do not wait for autonegtation to complete I
2963 * do not see a valid link status.
2964 * wait_autoneg_complete = 1 .
2965 */
wdenk682011f2003-06-03 23:54:09 +00002966 if (hw->wait_autoneg_complete) {
2967 ret_val = e1000_wait_autoneg(hw);
Roy Zangaa070782009-07-31 13:34:02 +08002968 if (ret_val) {
2969 DEBUGOUT("Error while waiting for autoneg"
2970 "to complete\n");
wdenk682011f2003-06-03 23:54:09 +00002971 return ret_val;
2972 }
2973 }
Roy Zangaa070782009-07-31 13:34:02 +08002974
York Sun472d5462013-04-01 11:29:11 -07002975 hw->get_link_status = true;
Roy Zangaa070782009-07-31 13:34:02 +08002976
2977 return E1000_SUCCESS;
2978}
2979
2980/******************************************************************************
2981* Config the MAC and the PHY after link is up.
2982* 1) Set up the MAC to the current PHY speed/duplex
2983* if we are on 82543. If we
2984* are on newer silicon, we only need to configure
2985* collision distance in the Transmit Control Register.
2986* 2) Set up flow control on the MAC to that established with
2987* the link partner.
2988* 3) Config DSP to improve Gigabit link quality for some PHY revisions.
2989*
2990* hw - Struct containing variables accessed by shared code
2991******************************************************************************/
2992static int32_t
2993e1000_copper_link_postconfig(struct e1000_hw *hw)
2994{
2995 int32_t ret_val;
2996 DEBUGFUNC();
2997
2998 if (hw->mac_type >= e1000_82544) {
2999 e1000_config_collision_dist(hw);
3000 } else {
3001 ret_val = e1000_config_mac_to_phy(hw);
3002 if (ret_val) {
3003 DEBUGOUT("Error configuring MAC to PHY settings\n");
3004 return ret_val;
3005 }
3006 }
3007 ret_val = e1000_config_fc_after_link_up(hw);
3008 if (ret_val) {
3009 DEBUGOUT("Error Configuring Flow Control\n");
wdenk682011f2003-06-03 23:54:09 +00003010 return ret_val;
3011 }
Roy Zangaa070782009-07-31 13:34:02 +08003012 return E1000_SUCCESS;
3013}
3014
3015/******************************************************************************
3016* Detects which PHY is present and setup the speed and duplex
3017*
3018* hw - Struct containing variables accessed by shared code
3019******************************************************************************/
3020static int
Simon Glass5c5e7072015-08-19 09:33:39 -06003021e1000_setup_copper_link(struct e1000_hw *hw)
Roy Zangaa070782009-07-31 13:34:02 +08003022{
Roy Zangaa070782009-07-31 13:34:02 +08003023 int32_t ret_val;
3024 uint16_t i;
3025 uint16_t phy_data;
3026 uint16_t reg_data;
3027
3028 DEBUGFUNC();
3029
3030 switch (hw->mac_type) {
3031 case e1000_80003es2lan:
3032 case e1000_ich8lan:
3033 /* Set the mac to wait the maximum time between each
3034 * iteration and increase the max iterations when
3035 * polling the phy; this fixes erroneous timeouts at 10Mbps. */
3036 ret_val = e1000_write_kmrn_reg(hw,
3037 GG82563_REG(0x34, 4), 0xFFFF);
3038 if (ret_val)
3039 return ret_val;
3040 ret_val = e1000_read_kmrn_reg(hw,
3041 GG82563_REG(0x34, 9), &reg_data);
3042 if (ret_val)
3043 return ret_val;
3044 reg_data |= 0x3F;
3045 ret_val = e1000_write_kmrn_reg(hw,
3046 GG82563_REG(0x34, 9), reg_data);
3047 if (ret_val)
3048 return ret_val;
3049 default:
3050 break;
3051 }
3052
3053 /* Check if it is a valid PHY and set PHY mode if necessary. */
3054 ret_val = e1000_copper_link_preconfig(hw);
3055 if (ret_val)
3056 return ret_val;
3057 switch (hw->mac_type) {
3058 case e1000_80003es2lan:
3059 /* Kumeran registers are written-only */
3060 reg_data =
3061 E1000_KUMCTRLSTA_INB_CTRL_LINK_STATUS_TX_TIMEOUT_DEFAULT;
3062 reg_data |= E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING;
3063 ret_val = e1000_write_kmrn_reg(hw,
3064 E1000_KUMCTRLSTA_OFFSET_INB_CTRL, reg_data);
3065 if (ret_val)
3066 return ret_val;
3067 break;
3068 default:
3069 break;
3070 }
3071
3072 if (hw->phy_type == e1000_phy_igp ||
3073 hw->phy_type == e1000_phy_igp_3 ||
3074 hw->phy_type == e1000_phy_igp_2) {
3075 ret_val = e1000_copper_link_igp_setup(hw);
3076 if (ret_val)
3077 return ret_val;
Marek Vasut95186062014-08-08 07:41:39 -07003078 } else if (hw->phy_type == e1000_phy_m88 ||
3079 hw->phy_type == e1000_phy_igb) {
Roy Zangaa070782009-07-31 13:34:02 +08003080 ret_val = e1000_copper_link_mgp_setup(hw);
3081 if (ret_val)
3082 return ret_val;
3083 } else if (hw->phy_type == e1000_phy_gg82563) {
3084 ret_val = e1000_copper_link_ggp_setup(hw);
3085 if (ret_val)
3086 return ret_val;
3087 }
3088
3089 /* always auto */
3090 /* Setup autoneg and flow control advertisement
3091 * and perform autonegotiation */
3092 ret_val = e1000_copper_link_autoneg(hw);
3093 if (ret_val)
3094 return ret_val;
wdenk682011f2003-06-03 23:54:09 +00003095
3096 /* Check link status. Wait up to 100 microseconds for link to become
3097 * valid.
3098 */
3099 for (i = 0; i < 10; i++) {
Roy Zangaa070782009-07-31 13:34:02 +08003100 ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
3101 if (ret_val)
3102 return ret_val;
3103 ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
3104 if (ret_val)
3105 return ret_val;
3106
wdenk682011f2003-06-03 23:54:09 +00003107 if (phy_data & MII_SR_LINK_STATUS) {
Roy Zangaa070782009-07-31 13:34:02 +08003108 /* Config the MAC and PHY after link is up */
3109 ret_val = e1000_copper_link_postconfig(hw);
3110 if (ret_val)
wdenk682011f2003-06-03 23:54:09 +00003111 return ret_val;
Roy Zangaa070782009-07-31 13:34:02 +08003112
wdenk682011f2003-06-03 23:54:09 +00003113 DEBUGOUT("Valid link established!!!\n");
Roy Zangaa070782009-07-31 13:34:02 +08003114 return E1000_SUCCESS;
wdenk682011f2003-06-03 23:54:09 +00003115 }
3116 udelay(10);
3117 }
3118
3119 DEBUGOUT("Unable to establish link!!!\n");
Roy Zangaa070782009-07-31 13:34:02 +08003120 return E1000_SUCCESS;
wdenk682011f2003-06-03 23:54:09 +00003121}
3122
3123/******************************************************************************
3124* Configures PHY autoneg and flow control advertisement settings
3125*
3126* hw - Struct containing variables accessed by shared code
3127******************************************************************************/
Roy Zangaa070782009-07-31 13:34:02 +08003128int32_t
wdenk682011f2003-06-03 23:54:09 +00003129e1000_phy_setup_autoneg(struct e1000_hw *hw)
3130{
Roy Zangaa070782009-07-31 13:34:02 +08003131 int32_t ret_val;
wdenk682011f2003-06-03 23:54:09 +00003132 uint16_t mii_autoneg_adv_reg;
3133 uint16_t mii_1000t_ctrl_reg;
3134
3135 DEBUGFUNC();
3136
3137 /* Read the MII Auto-Neg Advertisement Register (Address 4). */
Roy Zangaa070782009-07-31 13:34:02 +08003138 ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
3139 if (ret_val)
3140 return ret_val;
wdenk682011f2003-06-03 23:54:09 +00003141
Roy Zangaa070782009-07-31 13:34:02 +08003142 if (hw->phy_type != e1000_phy_ife) {
3143 /* Read the MII 1000Base-T Control Register (Address 9). */
3144 ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL,
3145 &mii_1000t_ctrl_reg);
3146 if (ret_val)
3147 return ret_val;
3148 } else
3149 mii_1000t_ctrl_reg = 0;
wdenk682011f2003-06-03 23:54:09 +00003150
3151 /* Need to parse both autoneg_advertised and fc and set up
3152 * the appropriate PHY registers. First we will parse for
3153 * autoneg_advertised software override. Since we can advertise
3154 * a plethora of combinations, we need to check each bit
3155 * individually.
3156 */
3157
3158 /* First we clear all the 10/100 mb speed bits in the Auto-Neg
3159 * Advertisement Register (Address 4) and the 1000 mb speed bits in
Roy Zangaa070782009-07-31 13:34:02 +08003160 * the 1000Base-T Control Register (Address 9).
wdenk682011f2003-06-03 23:54:09 +00003161 */
3162 mii_autoneg_adv_reg &= ~REG4_SPEED_MASK;
3163 mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK;
3164
3165 DEBUGOUT("autoneg_advertised %x\n", hw->autoneg_advertised);
3166
3167 /* Do we want to advertise 10 Mb Half Duplex? */
3168 if (hw->autoneg_advertised & ADVERTISE_10_HALF) {
3169 DEBUGOUT("Advertise 10mb Half duplex\n");
3170 mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
3171 }
3172
3173 /* Do we want to advertise 10 Mb Full Duplex? */
3174 if (hw->autoneg_advertised & ADVERTISE_10_FULL) {
3175 DEBUGOUT("Advertise 10mb Full duplex\n");
3176 mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
3177 }
3178
3179 /* Do we want to advertise 100 Mb Half Duplex? */
3180 if (hw->autoneg_advertised & ADVERTISE_100_HALF) {
3181 DEBUGOUT("Advertise 100mb Half duplex\n");
3182 mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
3183 }
3184
3185 /* Do we want to advertise 100 Mb Full Duplex? */
3186 if (hw->autoneg_advertised & ADVERTISE_100_FULL) {
3187 DEBUGOUT("Advertise 100mb Full duplex\n");
3188 mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
3189 }
3190
3191 /* We do not allow the Phy to advertise 1000 Mb Half Duplex */
3192 if (hw->autoneg_advertised & ADVERTISE_1000_HALF) {
3193 DEBUGOUT
3194 ("Advertise 1000mb Half duplex requested, request denied!\n");
3195 }
3196
3197 /* Do we want to advertise 1000 Mb Full Duplex? */
3198 if (hw->autoneg_advertised & ADVERTISE_1000_FULL) {
3199 DEBUGOUT("Advertise 1000mb Full duplex\n");
3200 mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
3201 }
3202
3203 /* Check for a software override of the flow control settings, and
3204 * setup the PHY advertisement registers accordingly. If
3205 * auto-negotiation is enabled, then software will have to set the
3206 * "PAUSE" bits to the correct value in the Auto-Negotiation
3207 * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-negotiation.
3208 *
3209 * The possible values of the "fc" parameter are:
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07003210 * 0: Flow control is completely disabled
3211 * 1: Rx flow control is enabled (we can receive pause frames
3212 * but not send pause frames).
3213 * 2: Tx flow control is enabled (we can send pause frames
3214 * but we do not support receiving pause frames).
3215 * 3: Both Rx and TX flow control (symmetric) are enabled.
wdenk682011f2003-06-03 23:54:09 +00003216 * other: No software override. The flow control configuration
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07003217 * in the EEPROM is used.
wdenk682011f2003-06-03 23:54:09 +00003218 */
3219 switch (hw->fc) {
3220 case e1000_fc_none: /* 0 */
3221 /* Flow control (RX & TX) is completely disabled by a
3222 * software over-ride.
3223 */
3224 mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
3225 break;
3226 case e1000_fc_rx_pause: /* 1 */
3227 /* RX Flow control is enabled, and TX Flow control is
3228 * disabled, by a software over-ride.
3229 */
3230 /* Since there really isn't a way to advertise that we are
3231 * capable of RX Pause ONLY, we will advertise that we
3232 * support both symmetric and asymmetric RX PAUSE. Later
3233 * (in e1000_config_fc_after_link_up) we will disable the
3234 *hw's ability to send PAUSE frames.
3235 */
3236 mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
3237 break;
3238 case e1000_fc_tx_pause: /* 2 */
3239 /* TX Flow control is enabled, and RX Flow control is
3240 * disabled, by a software over-ride.
3241 */
3242 mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
3243 mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
3244 break;
3245 case e1000_fc_full: /* 3 */
3246 /* Flow control (both RX and TX) is enabled by a software
3247 * over-ride.
3248 */
3249 mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
3250 break;
3251 default:
3252 DEBUGOUT("Flow control param set incorrectly\n");
3253 return -E1000_ERR_CONFIG;
3254 }
3255
Roy Zangaa070782009-07-31 13:34:02 +08003256 ret_val = e1000_write_phy_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg);
3257 if (ret_val)
3258 return ret_val;
wdenk682011f2003-06-03 23:54:09 +00003259
3260 DEBUGOUT("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
3261
Roy Zangaa070782009-07-31 13:34:02 +08003262 if (hw->phy_type != e1000_phy_ife) {
3263 ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL,
3264 mii_1000t_ctrl_reg);
3265 if (ret_val)
3266 return ret_val;
wdenk682011f2003-06-03 23:54:09 +00003267 }
Roy Zangaa070782009-07-31 13:34:02 +08003268
3269 return E1000_SUCCESS;
wdenk682011f2003-06-03 23:54:09 +00003270}
3271
3272/******************************************************************************
3273* Sets the collision distance in the Transmit Control register
3274*
3275* hw - Struct containing variables accessed by shared code
3276*
3277* Link should have been established previously. Reads the speed and duplex
3278* information from the Device Status register.
3279******************************************************************************/
3280static void
3281e1000_config_collision_dist(struct e1000_hw *hw)
3282{
Roy Zangaa070782009-07-31 13:34:02 +08003283 uint32_t tctl, coll_dist;
3284
3285 DEBUGFUNC();
3286
3287 if (hw->mac_type < e1000_82543)
3288 coll_dist = E1000_COLLISION_DISTANCE_82542;
3289 else
3290 coll_dist = E1000_COLLISION_DISTANCE;
wdenk682011f2003-06-03 23:54:09 +00003291
3292 tctl = E1000_READ_REG(hw, TCTL);
3293
3294 tctl &= ~E1000_TCTL_COLD;
Roy Zangaa070782009-07-31 13:34:02 +08003295 tctl |= coll_dist << E1000_COLD_SHIFT;
wdenk682011f2003-06-03 23:54:09 +00003296
3297 E1000_WRITE_REG(hw, TCTL, tctl);
3298 E1000_WRITE_FLUSH(hw);
3299}
3300
3301/******************************************************************************
3302* Sets MAC speed and duplex settings to reflect the those in the PHY
3303*
3304* hw - Struct containing variables accessed by shared code
3305* mii_reg - data to write to the MII control register
3306*
3307* The contents of the PHY register containing the needed information need to
3308* be passed in.
3309******************************************************************************/
3310static int
3311e1000_config_mac_to_phy(struct e1000_hw *hw)
3312{
3313 uint32_t ctrl;
3314 uint16_t phy_data;
3315
3316 DEBUGFUNC();
3317
3318 /* Read the Device Control Register and set the bits to Force Speed
3319 * and Duplex.
3320 */
3321 ctrl = E1000_READ_REG(hw, CTRL);
3322 ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
Marek Vasut95186062014-08-08 07:41:39 -07003323 ctrl &= ~(E1000_CTRL_ILOS);
3324 ctrl |= (E1000_CTRL_SPD_SEL);
wdenk682011f2003-06-03 23:54:09 +00003325
3326 /* Set up duplex in the Device Control and Transmit Control
3327 * registers depending on negotiated values.
3328 */
3329 if (e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data) < 0) {
3330 DEBUGOUT("PHY Read Error\n");
3331 return -E1000_ERR_PHY;
3332 }
3333 if (phy_data & M88E1000_PSSR_DPLX)
3334 ctrl |= E1000_CTRL_FD;
3335 else
3336 ctrl &= ~E1000_CTRL_FD;
3337
3338 e1000_config_collision_dist(hw);
3339
3340 /* Set up speed in the Device Control register depending on
3341 * negotiated values.
3342 */
3343 if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS)
3344 ctrl |= E1000_CTRL_SPD_1000;
3345 else if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS)
3346 ctrl |= E1000_CTRL_SPD_100;
3347 /* Write the configured values back to the Device Control Reg. */
3348 E1000_WRITE_REG(hw, CTRL, ctrl);
3349 return 0;
3350}
3351
3352/******************************************************************************
3353 * Forces the MAC's flow control settings.
wdenk8bde7f72003-06-27 21:31:46 +00003354 *
wdenk682011f2003-06-03 23:54:09 +00003355 * hw - Struct containing variables accessed by shared code
3356 *
3357 * Sets the TFCE and RFCE bits in the device control register to reflect
3358 * the adapter settings. TFCE and RFCE need to be explicitly set by
3359 * software when a Copper PHY is used because autonegotiation is managed
3360 * by the PHY rather than the MAC. Software must also configure these
3361 * bits when link is forced on a fiber connection.
3362 *****************************************************************************/
3363static int
3364e1000_force_mac_fc(struct e1000_hw *hw)
3365{
3366 uint32_t ctrl;
3367
3368 DEBUGFUNC();
3369
3370 /* Get the current configuration of the Device Control Register */
3371 ctrl = E1000_READ_REG(hw, CTRL);
3372
3373 /* Because we didn't get link via the internal auto-negotiation
3374 * mechanism (we either forced link or we got link via PHY
3375 * auto-neg), we have to manually enable/disable transmit an
3376 * receive flow control.
3377 *
3378 * The "Case" statement below enables/disable flow control
3379 * according to the "hw->fc" parameter.
3380 *
3381 * The possible values of the "fc" parameter are:
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07003382 * 0: Flow control is completely disabled
3383 * 1: Rx flow control is enabled (we can receive pause
3384 * frames but not send pause frames).
3385 * 2: Tx flow control is enabled (we can send pause frames
3386 * frames but we do not receive pause frames).
3387 * 3: Both Rx and TX flow control (symmetric) is enabled.
wdenk682011f2003-06-03 23:54:09 +00003388 * other: No other values should be possible at this point.
3389 */
3390
3391 switch (hw->fc) {
3392 case e1000_fc_none:
3393 ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE));
3394 break;
3395 case e1000_fc_rx_pause:
3396 ctrl &= (~E1000_CTRL_TFCE);
3397 ctrl |= E1000_CTRL_RFCE;
3398 break;
3399 case e1000_fc_tx_pause:
3400 ctrl &= (~E1000_CTRL_RFCE);
3401 ctrl |= E1000_CTRL_TFCE;
3402 break;
3403 case e1000_fc_full:
3404 ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE);
3405 break;
3406 default:
3407 DEBUGOUT("Flow control param set incorrectly\n");
3408 return -E1000_ERR_CONFIG;
3409 }
3410
3411 /* Disable TX Flow Control for 82542 (rev 2.0) */
3412 if (hw->mac_type == e1000_82542_rev2_0)
3413 ctrl &= (~E1000_CTRL_TFCE);
3414
3415 E1000_WRITE_REG(hw, CTRL, ctrl);
3416 return 0;
3417}
3418
3419/******************************************************************************
3420 * Configures flow control settings after link is established
wdenk8bde7f72003-06-27 21:31:46 +00003421 *
wdenk682011f2003-06-03 23:54:09 +00003422 * hw - Struct containing variables accessed by shared code
3423 *
3424 * Should be called immediately after a valid link has been established.
3425 * Forces MAC flow control settings if link was forced. When in MII/GMII mode
3426 * and autonegotiation is enabled, the MAC flow control settings will be set
3427 * based on the flow control negotiated by the PHY. In TBI mode, the TFCE
3428 * and RFCE bits will be automaticaly set to the negotiated flow control mode.
3429 *****************************************************************************/
Roy Zangaa070782009-07-31 13:34:02 +08003430static int32_t
wdenk682011f2003-06-03 23:54:09 +00003431e1000_config_fc_after_link_up(struct e1000_hw *hw)
3432{
3433 int32_t ret_val;
3434 uint16_t mii_status_reg;
3435 uint16_t mii_nway_adv_reg;
3436 uint16_t mii_nway_lp_ability_reg;
3437 uint16_t speed;
3438 uint16_t duplex;
3439
3440 DEBUGFUNC();
3441
3442 /* Check for the case where we have fiber media and auto-neg failed
3443 * so we had to force link. In this case, we need to force the
3444 * configuration of the MAC to match the "fc" parameter.
3445 */
Roy Zangaa070782009-07-31 13:34:02 +08003446 if (((hw->media_type == e1000_media_type_fiber) && (hw->autoneg_failed))
3447 || ((hw->media_type == e1000_media_type_internal_serdes)
3448 && (hw->autoneg_failed))
3449 || ((hw->media_type == e1000_media_type_copper)
3450 && (!hw->autoneg))) {
wdenk682011f2003-06-03 23:54:09 +00003451 ret_val = e1000_force_mac_fc(hw);
3452 if (ret_val < 0) {
3453 DEBUGOUT("Error forcing flow control settings\n");
3454 return ret_val;
3455 }
3456 }
3457
3458 /* Check for the case where we have copper media and auto-neg is
3459 * enabled. In this case, we need to check and see if Auto-Neg
3460 * has completed, and if so, how the PHY and link partner has
3461 * flow control configured.
3462 */
3463 if (hw->media_type == e1000_media_type_copper) {
3464 /* Read the MII Status Register and check to see if AutoNeg
3465 * has completed. We read this twice because this reg has
3466 * some "sticky" (latched) bits.
3467 */
3468 if (e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg) < 0) {
Minghuan Lian5abf13e2015-03-19 09:43:51 -07003469 DEBUGOUT("PHY Read Error\n");
wdenk682011f2003-06-03 23:54:09 +00003470 return -E1000_ERR_PHY;
3471 }
3472 if (e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg) < 0) {
Minghuan Lian5abf13e2015-03-19 09:43:51 -07003473 DEBUGOUT("PHY Read Error\n");
wdenk682011f2003-06-03 23:54:09 +00003474 return -E1000_ERR_PHY;
3475 }
3476
3477 if (mii_status_reg & MII_SR_AUTONEG_COMPLETE) {
3478 /* The AutoNeg process has completed, so we now need to
3479 * read both the Auto Negotiation Advertisement Register
3480 * (Address 4) and the Auto_Negotiation Base Page Ability
3481 * Register (Address 5) to determine how flow control was
3482 * negotiated.
3483 */
3484 if (e1000_read_phy_reg
3485 (hw, PHY_AUTONEG_ADV, &mii_nway_adv_reg) < 0) {
3486 DEBUGOUT("PHY Read Error\n");
3487 return -E1000_ERR_PHY;
3488 }
3489 if (e1000_read_phy_reg
3490 (hw, PHY_LP_ABILITY,
3491 &mii_nway_lp_ability_reg) < 0) {
3492 DEBUGOUT("PHY Read Error\n");
3493 return -E1000_ERR_PHY;
3494 }
3495
3496 /* Two bits in the Auto Negotiation Advertisement Register
3497 * (Address 4) and two bits in the Auto Negotiation Base
3498 * Page Ability Register (Address 5) determine flow control
3499 * for both the PHY and the link partner. The following
3500 * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
3501 * 1999, describes these PAUSE resolution bits and how flow
3502 * control is determined based upon these settings.
3503 * NOTE: DC = Don't Care
3504 *
3505 * LOCAL DEVICE | LINK PARTNER
3506 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
3507 *-------|---------|-------|---------|--------------------
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07003508 * 0 | 0 | DC | DC | e1000_fc_none
3509 * 0 | 1 | 0 | DC | e1000_fc_none
3510 * 0 | 1 | 1 | 0 | e1000_fc_none
3511 * 0 | 1 | 1 | 1 | e1000_fc_tx_pause
3512 * 1 | 0 | 0 | DC | e1000_fc_none
3513 * 1 | DC | 1 | DC | e1000_fc_full
3514 * 1 | 1 | 0 | 0 | e1000_fc_none
3515 * 1 | 1 | 0 | 1 | e1000_fc_rx_pause
wdenk682011f2003-06-03 23:54:09 +00003516 *
3517 */
3518 /* Are both PAUSE bits set to 1? If so, this implies
3519 * Symmetric Flow Control is enabled at both ends. The
3520 * ASM_DIR bits are irrelevant per the spec.
3521 *
3522 * For Symmetric Flow Control:
3523 *
3524 * LOCAL DEVICE | LINK PARTNER
3525 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
3526 *-------|---------|-------|---------|--------------------
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07003527 * 1 | DC | 1 | DC | e1000_fc_full
wdenk682011f2003-06-03 23:54:09 +00003528 *
3529 */
3530 if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
3531 (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) {
3532 /* Now we need to check if the user selected RX ONLY
3533 * of pause frames. In this case, we had to advertise
3534 * FULL flow control because we could not advertise RX
3535 * ONLY. Hence, we must now check to see if we need to
3536 * turn OFF the TRANSMISSION of PAUSE frames.
3537 */
3538 if (hw->original_fc == e1000_fc_full) {
3539 hw->fc = e1000_fc_full;
3540 DEBUGOUT("Flow Control = FULL.\r\n");
3541 } else {
3542 hw->fc = e1000_fc_rx_pause;
3543 DEBUGOUT
3544 ("Flow Control = RX PAUSE frames only.\r\n");
3545 }
3546 }
3547 /* For receiving PAUSE frames ONLY.
3548 *
3549 * LOCAL DEVICE | LINK PARTNER
3550 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
3551 *-------|---------|-------|---------|--------------------
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07003552 * 0 | 1 | 1 | 1 | e1000_fc_tx_pause
wdenk682011f2003-06-03 23:54:09 +00003553 *
3554 */
3555 else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) &&
3556 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
3557 (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
3558 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR))
3559 {
3560 hw->fc = e1000_fc_tx_pause;
3561 DEBUGOUT
3562 ("Flow Control = TX PAUSE frames only.\r\n");
3563 }
3564 /* For transmitting PAUSE frames ONLY.
3565 *
3566 * LOCAL DEVICE | LINK PARTNER
3567 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
3568 *-------|---------|-------|---------|--------------------
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07003569 * 1 | 1 | 0 | 1 | e1000_fc_rx_pause
wdenk682011f2003-06-03 23:54:09 +00003570 *
3571 */
3572 else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
3573 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
3574 !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
3575 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR))
3576 {
3577 hw->fc = e1000_fc_rx_pause;
3578 DEBUGOUT
3579 ("Flow Control = RX PAUSE frames only.\r\n");
3580 }
3581 /* Per the IEEE spec, at this point flow control should be
3582 * disabled. However, we want to consider that we could
3583 * be connected to a legacy switch that doesn't advertise
3584 * desired flow control, but can be forced on the link
3585 * partner. So if we advertised no flow control, that is
3586 * what we will resolve to. If we advertised some kind of
3587 * receive capability (Rx Pause Only or Full Flow Control)
3588 * and the link partner advertised none, we will configure
3589 * ourselves to enable Rx Flow Control only. We can do
3590 * this safely for two reasons: If the link partner really
3591 * didn't want flow control enabled, and we enable Rx, no
3592 * harm done since we won't be receiving any PAUSE frames
3593 * anyway. If the intent on the link partner was to have
3594 * flow control enabled, then by us enabling RX only, we
3595 * can at least receive pause frames and process them.
3596 * This is a good idea because in most cases, since we are
3597 * predominantly a server NIC, more times than not we will
3598 * be asked to delay transmission of packets than asking
3599 * our link partner to pause transmission of frames.
3600 */
3601 else if (hw->original_fc == e1000_fc_none ||
3602 hw->original_fc == e1000_fc_tx_pause) {
3603 hw->fc = e1000_fc_none;
3604 DEBUGOUT("Flow Control = NONE.\r\n");
3605 } else {
3606 hw->fc = e1000_fc_rx_pause;
3607 DEBUGOUT
3608 ("Flow Control = RX PAUSE frames only.\r\n");
3609 }
3610
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07003611 /* Now we need to do one last check... If we auto-
wdenk682011f2003-06-03 23:54:09 +00003612 * negotiated to HALF DUPLEX, flow control should not be
3613 * enabled per IEEE 802.3 spec.
3614 */
3615 e1000_get_speed_and_duplex(hw, &speed, &duplex);
3616
3617 if (duplex == HALF_DUPLEX)
3618 hw->fc = e1000_fc_none;
3619
3620 /* Now we call a subroutine to actually force the MAC
3621 * controller to use the correct flow control settings.
3622 */
3623 ret_val = e1000_force_mac_fc(hw);
3624 if (ret_val < 0) {
3625 DEBUGOUT
3626 ("Error forcing flow control settings\n");
3627 return ret_val;
3628 }
3629 } else {
3630 DEBUGOUT
3631 ("Copper PHY and Auto Neg has not completed.\r\n");
3632 }
3633 }
Roy Zangaa070782009-07-31 13:34:02 +08003634 return E1000_SUCCESS;
wdenk682011f2003-06-03 23:54:09 +00003635}
3636
3637/******************************************************************************
3638 * Checks to see if the link status of the hardware has changed.
3639 *
3640 * hw - Struct containing variables accessed by shared code
3641 *
3642 * Called by any function that needs to check the link status of the adapter.
3643 *****************************************************************************/
3644static int
Simon Glass5c5e7072015-08-19 09:33:39 -06003645e1000_check_for_link(struct e1000_hw *hw)
wdenk682011f2003-06-03 23:54:09 +00003646{
wdenk682011f2003-06-03 23:54:09 +00003647 uint32_t rxcw;
3648 uint32_t ctrl;
3649 uint32_t status;
3650 uint32_t rctl;
3651 uint32_t signal;
3652 int32_t ret_val;
3653 uint16_t phy_data;
3654 uint16_t lp_capability;
3655
3656 DEBUGFUNC();
3657
wdenk8bde7f72003-06-27 21:31:46 +00003658 /* On adapters with a MAC newer that 82544, SW Defineable pin 1 will be
3659 * set when the optics detect a signal. On older adapters, it will be
wdenk682011f2003-06-03 23:54:09 +00003660 * cleared when there is a signal
3661 */
3662 ctrl = E1000_READ_REG(hw, CTRL);
3663 if ((hw->mac_type > e1000_82544) && !(ctrl & E1000_CTRL_ILOS))
3664 signal = E1000_CTRL_SWDPIN1;
3665 else
3666 signal = 0;
3667
3668 status = E1000_READ_REG(hw, STATUS);
3669 rxcw = E1000_READ_REG(hw, RXCW);
3670 DEBUGOUT("ctrl: %#08x status %#08x rxcw %#08x\n", ctrl, status, rxcw);
3671
3672 /* If we have a copper PHY then we only want to go out to the PHY
3673 * registers to see if Auto-Neg has completed and/or if our link
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07003674 * status has changed. The get_link_status flag will be set if we
wdenk682011f2003-06-03 23:54:09 +00003675 * receive a Link Status Change interrupt or we have Rx Sequence
3676 * Errors.
3677 */
3678 if ((hw->media_type == e1000_media_type_copper) && hw->get_link_status) {
3679 /* First we want to see if the MII Status Register reports
3680 * link. If so, then we want to get the current speed/duplex
3681 * of the PHY.
3682 * Read the register twice since the link bit is sticky.
3683 */
3684 if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) {
3685 DEBUGOUT("PHY Read Error\n");
3686 return -E1000_ERR_PHY;
3687 }
3688 if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) {
3689 DEBUGOUT("PHY Read Error\n");
3690 return -E1000_ERR_PHY;
3691 }
3692
3693 if (phy_data & MII_SR_LINK_STATUS) {
York Sun472d5462013-04-01 11:29:11 -07003694 hw->get_link_status = false;
wdenk682011f2003-06-03 23:54:09 +00003695 } else {
3696 /* No link detected */
3697 return -E1000_ERR_NOLINK;
3698 }
3699
3700 /* We have a M88E1000 PHY and Auto-Neg is enabled. If we
3701 * have Si on board that is 82544 or newer, Auto
3702 * Speed Detection takes care of MAC speed/duplex
3703 * configuration. So we only need to configure Collision
3704 * Distance in the MAC. Otherwise, we need to force
3705 * speed/duplex on the MAC to the current PHY speed/duplex
3706 * settings.
3707 */
3708 if (hw->mac_type >= e1000_82544)
3709 e1000_config_collision_dist(hw);
3710 else {
3711 ret_val = e1000_config_mac_to_phy(hw);
3712 if (ret_val < 0) {
3713 DEBUGOUT
3714 ("Error configuring MAC to PHY settings\n");
3715 return ret_val;
3716 }
3717 }
3718
wdenk8bde7f72003-06-27 21:31:46 +00003719 /* Configure Flow Control now that Auto-Neg has completed. First, we
wdenk682011f2003-06-03 23:54:09 +00003720 * need to restore the desired flow control settings because we may
3721 * have had to re-autoneg with a different link partner.
3722 */
3723 ret_val = e1000_config_fc_after_link_up(hw);
3724 if (ret_val < 0) {
3725 DEBUGOUT("Error configuring flow control\n");
3726 return ret_val;
3727 }
3728
3729 /* At this point we know that we are on copper and we have
3730 * auto-negotiated link. These are conditions for checking the link
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07003731 * parter capability register. We use the link partner capability to
wdenk682011f2003-06-03 23:54:09 +00003732 * determine if TBI Compatibility needs to be turned on or off. If
3733 * the link partner advertises any speed in addition to Gigabit, then
3734 * we assume that they are GMII-based, and TBI compatibility is not
3735 * needed. If no other speeds are advertised, we assume the link
3736 * partner is TBI-based, and we turn on TBI Compatibility.
3737 */
3738 if (hw->tbi_compatibility_en) {
3739 if (e1000_read_phy_reg
3740 (hw, PHY_LP_ABILITY, &lp_capability) < 0) {
3741 DEBUGOUT("PHY Read Error\n");
3742 return -E1000_ERR_PHY;
3743 }
3744 if (lp_capability & (NWAY_LPAR_10T_HD_CAPS |
3745 NWAY_LPAR_10T_FD_CAPS |
3746 NWAY_LPAR_100TX_HD_CAPS |
3747 NWAY_LPAR_100TX_FD_CAPS |
3748 NWAY_LPAR_100T4_CAPS)) {
wdenk8bde7f72003-06-27 21:31:46 +00003749 /* If our link partner advertises anything in addition to
wdenk682011f2003-06-03 23:54:09 +00003750 * gigabit, we do not need to enable TBI compatibility.
3751 */
3752 if (hw->tbi_compatibility_on) {
3753 /* If we previously were in the mode, turn it off. */
3754 rctl = E1000_READ_REG(hw, RCTL);
3755 rctl &= ~E1000_RCTL_SBP;
3756 E1000_WRITE_REG(hw, RCTL, rctl);
York Sun472d5462013-04-01 11:29:11 -07003757 hw->tbi_compatibility_on = false;
wdenk682011f2003-06-03 23:54:09 +00003758 }
3759 } else {
3760 /* If TBI compatibility is was previously off, turn it on. For
3761 * compatibility with a TBI link partner, we will store bad
3762 * packets. Some frames have an additional byte on the end and
3763 * will look like CRC errors to to the hardware.
3764 */
3765 if (!hw->tbi_compatibility_on) {
York Sun472d5462013-04-01 11:29:11 -07003766 hw->tbi_compatibility_on = true;
wdenk682011f2003-06-03 23:54:09 +00003767 rctl = E1000_READ_REG(hw, RCTL);
3768 rctl |= E1000_RCTL_SBP;
3769 E1000_WRITE_REG(hw, RCTL, rctl);
3770 }
3771 }
3772 }
3773 }
3774 /* If we don't have link (auto-negotiation failed or link partner cannot
3775 * auto-negotiate), the cable is plugged in (we have signal), and our
3776 * link partner is not trying to auto-negotiate with us (we are receiving
3777 * idles or data), we need to force link up. We also need to give
3778 * auto-negotiation time to complete, in case the cable was just plugged
3779 * in. The autoneg_failed flag does this.
3780 */
3781 else if ((hw->media_type == e1000_media_type_fiber) &&
3782 (!(status & E1000_STATUS_LU)) &&
3783 ((ctrl & E1000_CTRL_SWDPIN1) == signal) &&
3784 (!(rxcw & E1000_RXCW_C))) {
3785 if (hw->autoneg_failed == 0) {
3786 hw->autoneg_failed = 1;
3787 return 0;
3788 }
3789 DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\r\n");
3790
3791 /* Disable auto-negotiation in the TXCW register */
3792 E1000_WRITE_REG(hw, TXCW, (hw->txcw & ~E1000_TXCW_ANE));
3793
3794 /* Force link-up and also force full-duplex. */
3795 ctrl = E1000_READ_REG(hw, CTRL);
3796 ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD);
3797 E1000_WRITE_REG(hw, CTRL, ctrl);
3798
3799 /* Configure Flow Control after forcing link up. */
3800 ret_val = e1000_config_fc_after_link_up(hw);
3801 if (ret_val < 0) {
3802 DEBUGOUT("Error configuring flow control\n");
3803 return ret_val;
3804 }
3805 }
3806 /* If we are forcing link and we are receiving /C/ ordered sets, re-enable
3807 * auto-negotiation in the TXCW register and disable forced link in the
3808 * Device Control register in an attempt to auto-negotiate with our link
3809 * partner.
3810 */
3811 else if ((hw->media_type == e1000_media_type_fiber) &&
3812 (ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
3813 DEBUGOUT
3814 ("RXing /C/, enable AutoNeg and stop forcing link.\r\n");
3815 E1000_WRITE_REG(hw, TXCW, hw->txcw);
3816 E1000_WRITE_REG(hw, CTRL, (ctrl & ~E1000_CTRL_SLU));
3817 }
3818 return 0;
3819}
3820
3821/******************************************************************************
Roy Zangaa070782009-07-31 13:34:02 +08003822* Configure the MAC-to-PHY interface for 10/100Mbps
3823*
3824* hw - Struct containing variables accessed by shared code
3825******************************************************************************/
3826static int32_t
3827e1000_configure_kmrn_for_10_100(struct e1000_hw *hw, uint16_t duplex)
3828{
3829 int32_t ret_val = E1000_SUCCESS;
3830 uint32_t tipg;
3831 uint16_t reg_data;
3832
3833 DEBUGFUNC();
3834
3835 reg_data = E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT;
3836 ret_val = e1000_write_kmrn_reg(hw,
3837 E1000_KUMCTRLSTA_OFFSET_HD_CTRL, reg_data);
3838 if (ret_val)
3839 return ret_val;
3840
3841 /* Configure Transmit Inter-Packet Gap */
3842 tipg = E1000_READ_REG(hw, TIPG);
3843 tipg &= ~E1000_TIPG_IPGT_MASK;
3844 tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_10_100;
3845 E1000_WRITE_REG(hw, TIPG, tipg);
3846
3847 ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data);
3848
3849 if (ret_val)
3850 return ret_val;
3851
3852 if (duplex == HALF_DUPLEX)
3853 reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER;
3854 else
3855 reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
3856
3857 ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
3858
3859 return ret_val;
3860}
3861
3862static int32_t
3863e1000_configure_kmrn_for_1000(struct e1000_hw *hw)
3864{
3865 int32_t ret_val = E1000_SUCCESS;
3866 uint16_t reg_data;
3867 uint32_t tipg;
3868
3869 DEBUGFUNC();
3870
3871 reg_data = E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT;
3872 ret_val = e1000_write_kmrn_reg(hw,
3873 E1000_KUMCTRLSTA_OFFSET_HD_CTRL, reg_data);
3874 if (ret_val)
3875 return ret_val;
3876
3877 /* Configure Transmit Inter-Packet Gap */
3878 tipg = E1000_READ_REG(hw, TIPG);
3879 tipg &= ~E1000_TIPG_IPGT_MASK;
3880 tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000;
3881 E1000_WRITE_REG(hw, TIPG, tipg);
3882
3883 ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data);
3884
3885 if (ret_val)
3886 return ret_val;
3887
3888 reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
3889 ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
3890
3891 return ret_val;
3892}
3893
3894/******************************************************************************
wdenk682011f2003-06-03 23:54:09 +00003895 * Detects the current speed and duplex settings of the hardware.
3896 *
3897 * hw - Struct containing variables accessed by shared code
3898 * speed - Speed of the connection
3899 * duplex - Duplex setting of the connection
3900 *****************************************************************************/
Roy Zangaa070782009-07-31 13:34:02 +08003901static int
3902e1000_get_speed_and_duplex(struct e1000_hw *hw, uint16_t *speed,
3903 uint16_t *duplex)
wdenk682011f2003-06-03 23:54:09 +00003904{
3905 uint32_t status;
Roy Zangaa070782009-07-31 13:34:02 +08003906 int32_t ret_val;
3907 uint16_t phy_data;
wdenk682011f2003-06-03 23:54:09 +00003908
3909 DEBUGFUNC();
3910
3911 if (hw->mac_type >= e1000_82543) {
3912 status = E1000_READ_REG(hw, STATUS);
3913 if (status & E1000_STATUS_SPEED_1000) {
3914 *speed = SPEED_1000;
3915 DEBUGOUT("1000 Mbs, ");
3916 } else if (status & E1000_STATUS_SPEED_100) {
3917 *speed = SPEED_100;
3918 DEBUGOUT("100 Mbs, ");
3919 } else {
3920 *speed = SPEED_10;
3921 DEBUGOUT("10 Mbs, ");
3922 }
3923
3924 if (status & E1000_STATUS_FD) {
3925 *duplex = FULL_DUPLEX;
3926 DEBUGOUT("Full Duplex\r\n");
3927 } else {
3928 *duplex = HALF_DUPLEX;
3929 DEBUGOUT(" Half Duplex\r\n");
3930 }
3931 } else {
3932 DEBUGOUT("1000 Mbs, Full Duplex\r\n");
3933 *speed = SPEED_1000;
3934 *duplex = FULL_DUPLEX;
3935 }
Roy Zangaa070782009-07-31 13:34:02 +08003936
3937 /* IGP01 PHY may advertise full duplex operation after speed downgrade
3938 * even if it is operating at half duplex. Here we set the duplex
3939 * settings to match the duplex in the link partner's capabilities.
3940 */
3941 if (hw->phy_type == e1000_phy_igp && hw->speed_downgraded) {
3942 ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_EXP, &phy_data);
3943 if (ret_val)
3944 return ret_val;
3945
3946 if (!(phy_data & NWAY_ER_LP_NWAY_CAPS))
3947 *duplex = HALF_DUPLEX;
3948 else {
3949 ret_val = e1000_read_phy_reg(hw,
3950 PHY_LP_ABILITY, &phy_data);
3951 if (ret_val)
3952 return ret_val;
3953 if ((*speed == SPEED_100 &&
3954 !(phy_data & NWAY_LPAR_100TX_FD_CAPS))
3955 || (*speed == SPEED_10
3956 && !(phy_data & NWAY_LPAR_10T_FD_CAPS)))
3957 *duplex = HALF_DUPLEX;
3958 }
3959 }
3960
3961 if ((hw->mac_type == e1000_80003es2lan) &&
3962 (hw->media_type == e1000_media_type_copper)) {
3963 if (*speed == SPEED_1000)
3964 ret_val = e1000_configure_kmrn_for_1000(hw);
3965 else
3966 ret_val = e1000_configure_kmrn_for_10_100(hw, *duplex);
3967 if (ret_val)
3968 return ret_val;
3969 }
3970 return E1000_SUCCESS;
wdenk682011f2003-06-03 23:54:09 +00003971}
3972
3973/******************************************************************************
3974* Blocks until autoneg completes or times out (~4.5 seconds)
3975*
3976* hw - Struct containing variables accessed by shared code
3977******************************************************************************/
3978static int
3979e1000_wait_autoneg(struct e1000_hw *hw)
3980{
3981 uint16_t i;
3982 uint16_t phy_data;
3983
3984 DEBUGFUNC();
3985 DEBUGOUT("Waiting for Auto-Neg to complete.\n");
3986
Stefan Roesefaa765d2015-08-11 17:12:44 +02003987 /* We will wait for autoneg to complete or timeout to expire. */
wdenk682011f2003-06-03 23:54:09 +00003988 for (i = PHY_AUTO_NEG_TIME; i > 0; i--) {
3989 /* Read the MII Status Register and wait for Auto-Neg
3990 * Complete bit to be set.
3991 */
3992 if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) {
3993 DEBUGOUT("PHY Read Error\n");
3994 return -E1000_ERR_PHY;
3995 }
3996 if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) {
3997 DEBUGOUT("PHY Read Error\n");
3998 return -E1000_ERR_PHY;
3999 }
4000 if (phy_data & MII_SR_AUTONEG_COMPLETE) {
4001 DEBUGOUT("Auto-Neg complete.\n");
4002 return 0;
4003 }
4004 mdelay(100);
4005 }
4006 DEBUGOUT("Auto-Neg timedout.\n");
4007 return -E1000_ERR_TIMEOUT;
4008}
4009
4010/******************************************************************************
4011* Raises the Management Data Clock
4012*
4013* hw - Struct containing variables accessed by shared code
4014* ctrl - Device control register's current value
4015******************************************************************************/
4016static void
4017e1000_raise_mdi_clk(struct e1000_hw *hw, uint32_t * ctrl)
4018{
4019 /* Raise the clock input to the Management Data Clock (by setting the MDC
4020 * bit), and then delay 2 microseconds.
4021 */
4022 E1000_WRITE_REG(hw, CTRL, (*ctrl | E1000_CTRL_MDC));
4023 E1000_WRITE_FLUSH(hw);
4024 udelay(2);
4025}
4026
4027/******************************************************************************
4028* Lowers the Management Data Clock
4029*
4030* hw - Struct containing variables accessed by shared code
4031* ctrl - Device control register's current value
4032******************************************************************************/
4033static void
4034e1000_lower_mdi_clk(struct e1000_hw *hw, uint32_t * ctrl)
4035{
4036 /* Lower the clock input to the Management Data Clock (by clearing the MDC
4037 * bit), and then delay 2 microseconds.
4038 */
4039 E1000_WRITE_REG(hw, CTRL, (*ctrl & ~E1000_CTRL_MDC));
4040 E1000_WRITE_FLUSH(hw);
4041 udelay(2);
4042}
4043
4044/******************************************************************************
4045* Shifts data bits out to the PHY
4046*
4047* hw - Struct containing variables accessed by shared code
4048* data - Data to send out to the PHY
4049* count - Number of bits to shift out
4050*
4051* Bits are shifted out in MSB to LSB order.
4052******************************************************************************/
4053static void
4054e1000_shift_out_mdi_bits(struct e1000_hw *hw, uint32_t data, uint16_t count)
4055{
4056 uint32_t ctrl;
4057 uint32_t mask;
4058
4059 /* We need to shift "count" number of bits out to the PHY. So, the value
wdenk8bde7f72003-06-27 21:31:46 +00004060 * in the "data" parameter will be shifted out to the PHY one bit at a
wdenk682011f2003-06-03 23:54:09 +00004061 * time. In order to do this, "data" must be broken down into bits.
4062 */
4063 mask = 0x01;
4064 mask <<= (count - 1);
4065
4066 ctrl = E1000_READ_REG(hw, CTRL);
4067
4068 /* Set MDIO_DIR and MDC_DIR direction bits to be used as output pins. */
4069 ctrl |= (E1000_CTRL_MDIO_DIR | E1000_CTRL_MDC_DIR);
4070
4071 while (mask) {
4072 /* A "1" is shifted out to the PHY by setting the MDIO bit to "1" and
4073 * then raising and lowering the Management Data Clock. A "0" is
4074 * shifted out to the PHY by setting the MDIO bit to "0" and then
4075 * raising and lowering the clock.
4076 */
4077 if (data & mask)
4078 ctrl |= E1000_CTRL_MDIO;
4079 else
4080 ctrl &= ~E1000_CTRL_MDIO;
4081
4082 E1000_WRITE_REG(hw, CTRL, ctrl);
4083 E1000_WRITE_FLUSH(hw);
4084
4085 udelay(2);
4086
4087 e1000_raise_mdi_clk(hw, &ctrl);
4088 e1000_lower_mdi_clk(hw, &ctrl);
4089
4090 mask = mask >> 1;
4091 }
4092}
4093
4094/******************************************************************************
4095* Shifts data bits in from the PHY
4096*
4097* hw - Struct containing variables accessed by shared code
4098*
wdenk8bde7f72003-06-27 21:31:46 +00004099* Bits are shifted in in MSB to LSB order.
wdenk682011f2003-06-03 23:54:09 +00004100******************************************************************************/
4101static uint16_t
4102e1000_shift_in_mdi_bits(struct e1000_hw *hw)
4103{
4104 uint32_t ctrl;
4105 uint16_t data = 0;
4106 uint8_t i;
4107
4108 /* In order to read a register from the PHY, we need to shift in a total
4109 * of 18 bits from the PHY. The first two bit (turnaround) times are used
4110 * to avoid contention on the MDIO pin when a read operation is performed.
4111 * These two bits are ignored by us and thrown away. Bits are "shifted in"
4112 * by raising the input to the Management Data Clock (setting the MDC bit),
4113 * and then reading the value of the MDIO bit.
4114 */
4115 ctrl = E1000_READ_REG(hw, CTRL);
4116
4117 /* Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as input. */
4118 ctrl &= ~E1000_CTRL_MDIO_DIR;
4119 ctrl &= ~E1000_CTRL_MDIO;
4120
4121 E1000_WRITE_REG(hw, CTRL, ctrl);
4122 E1000_WRITE_FLUSH(hw);
4123
4124 /* Raise and Lower the clock before reading in the data. This accounts for
4125 * the turnaround bits. The first clock occurred when we clocked out the
4126 * last bit of the Register Address.
4127 */
4128 e1000_raise_mdi_clk(hw, &ctrl);
4129 e1000_lower_mdi_clk(hw, &ctrl);
4130
4131 for (data = 0, i = 0; i < 16; i++) {
4132 data = data << 1;
4133 e1000_raise_mdi_clk(hw, &ctrl);
4134 ctrl = E1000_READ_REG(hw, CTRL);
4135 /* Check to see if we shifted in a "1". */
4136 if (ctrl & E1000_CTRL_MDIO)
4137 data |= 1;
4138 e1000_lower_mdi_clk(hw, &ctrl);
4139 }
4140
4141 e1000_raise_mdi_clk(hw, &ctrl);
4142 e1000_lower_mdi_clk(hw, &ctrl);
4143
4144 return data;
4145}
4146
4147/*****************************************************************************
4148* Reads the value from a PHY register
4149*
4150* hw - Struct containing variables accessed by shared code
4151* reg_addr - address of the PHY register to read
4152******************************************************************************/
4153static int
4154e1000_read_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t * phy_data)
4155{
4156 uint32_t i;
4157 uint32_t mdic = 0;
4158 const uint32_t phy_addr = 1;
4159
4160 if (reg_addr > MAX_PHY_REG_ADDRESS) {
4161 DEBUGOUT("PHY Address %d is out of range\n", reg_addr);
4162 return -E1000_ERR_PARAM;
4163 }
4164
4165 if (hw->mac_type > e1000_82543) {
4166 /* Set up Op-code, Phy Address, and register address in the MDI
4167 * Control register. The MAC will take care of interfacing with the
4168 * PHY to retrieve the desired data.
4169 */
4170 mdic = ((reg_addr << E1000_MDIC_REG_SHIFT) |
4171 (phy_addr << E1000_MDIC_PHY_SHIFT) |
4172 (E1000_MDIC_OP_READ));
4173
4174 E1000_WRITE_REG(hw, MDIC, mdic);
4175
4176 /* Poll the ready bit to see if the MDI read completed */
4177 for (i = 0; i < 64; i++) {
4178 udelay(10);
4179 mdic = E1000_READ_REG(hw, MDIC);
4180 if (mdic & E1000_MDIC_READY)
4181 break;
4182 }
4183 if (!(mdic & E1000_MDIC_READY)) {
4184 DEBUGOUT("MDI Read did not complete\n");
4185 return -E1000_ERR_PHY;
4186 }
4187 if (mdic & E1000_MDIC_ERROR) {
4188 DEBUGOUT("MDI Error\n");
4189 return -E1000_ERR_PHY;
4190 }
4191 *phy_data = (uint16_t) mdic;
4192 } else {
4193 /* We must first send a preamble through the MDIO pin to signal the
4194 * beginning of an MII instruction. This is done by sending 32
4195 * consecutive "1" bits.
4196 */
4197 e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE);
4198
4199 /* Now combine the next few fields that are required for a read
4200 * operation. We use this method instead of calling the
4201 * e1000_shift_out_mdi_bits routine five different times. The format of
4202 * a MII read instruction consists of a shift out of 14 bits and is
4203 * defined as follows:
4204 * <Preamble><SOF><Op Code><Phy Addr><Reg Addr>
4205 * followed by a shift in of 18 bits. This first two bits shifted in
4206 * are TurnAround bits used to avoid contention on the MDIO pin when a
4207 * READ operation is performed. These two bits are thrown away
4208 * followed by a shift in of 16 bits which contains the desired data.
4209 */
4210 mdic = ((reg_addr) | (phy_addr << 5) |
4211 (PHY_OP_READ << 10) | (PHY_SOF << 12));
4212
4213 e1000_shift_out_mdi_bits(hw, mdic, 14);
4214
4215 /* Now that we've shifted out the read command to the MII, we need to
4216 * "shift in" the 16-bit value (18 total bits) of the requested PHY
4217 * register address.
4218 */
4219 *phy_data = e1000_shift_in_mdi_bits(hw);
4220 }
4221 return 0;
4222}
4223
4224/******************************************************************************
4225* Writes a value to a PHY register
4226*
4227* hw - Struct containing variables accessed by shared code
4228* reg_addr - address of the PHY register to write
4229* data - data to write to the PHY
4230******************************************************************************/
4231static int
4232e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t phy_data)
4233{
4234 uint32_t i;
4235 uint32_t mdic = 0;
4236 const uint32_t phy_addr = 1;
4237
4238 if (reg_addr > MAX_PHY_REG_ADDRESS) {
4239 DEBUGOUT("PHY Address %d is out of range\n", reg_addr);
4240 return -E1000_ERR_PARAM;
4241 }
4242
4243 if (hw->mac_type > e1000_82543) {
4244 /* Set up Op-code, Phy Address, register address, and data intended
4245 * for the PHY register in the MDI Control register. The MAC will take
4246 * care of interfacing with the PHY to send the desired data.
4247 */
4248 mdic = (((uint32_t) phy_data) |
4249 (reg_addr << E1000_MDIC_REG_SHIFT) |
4250 (phy_addr << E1000_MDIC_PHY_SHIFT) |
4251 (E1000_MDIC_OP_WRITE));
4252
4253 E1000_WRITE_REG(hw, MDIC, mdic);
4254
4255 /* Poll the ready bit to see if the MDI read completed */
4256 for (i = 0; i < 64; i++) {
4257 udelay(10);
4258 mdic = E1000_READ_REG(hw, MDIC);
4259 if (mdic & E1000_MDIC_READY)
4260 break;
4261 }
4262 if (!(mdic & E1000_MDIC_READY)) {
4263 DEBUGOUT("MDI Write did not complete\n");
4264 return -E1000_ERR_PHY;
4265 }
4266 } else {
4267 /* We'll need to use the SW defined pins to shift the write command
4268 * out to the PHY. We first send a preamble to the PHY to signal the
wdenk8bde7f72003-06-27 21:31:46 +00004269 * beginning of the MII instruction. This is done by sending 32
wdenk682011f2003-06-03 23:54:09 +00004270 * consecutive "1" bits.
4271 */
4272 e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE);
4273
wdenk8bde7f72003-06-27 21:31:46 +00004274 /* Now combine the remaining required fields that will indicate a
wdenk682011f2003-06-03 23:54:09 +00004275 * write operation. We use this method instead of calling the
4276 * e1000_shift_out_mdi_bits routine for each field in the command. The
4277 * format of a MII write instruction is as follows:
4278 * <Preamble><SOF><Op Code><Phy Addr><Reg Addr><Turnaround><Data>.
4279 */
4280 mdic = ((PHY_TURNAROUND) | (reg_addr << 2) | (phy_addr << 7) |
4281 (PHY_OP_WRITE << 12) | (PHY_SOF << 14));
4282 mdic <<= 16;
4283 mdic |= (uint32_t) phy_data;
4284
4285 e1000_shift_out_mdi_bits(hw, mdic, 32);
4286 }
4287 return 0;
4288}
4289
4290/******************************************************************************
Roy Zangaa070782009-07-31 13:34:02 +08004291 * Checks if PHY reset is blocked due to SOL/IDER session, for example.
4292 * Returning E1000_BLK_PHY_RESET isn't necessarily an error. But it's up to
4293 * the caller to figure out how to deal with it.
4294 *
4295 * hw - Struct containing variables accessed by shared code
4296 *
4297 * returns: - E1000_BLK_PHY_RESET
4298 * E1000_SUCCESS
4299 *
4300 *****************************************************************************/
4301int32_t
4302e1000_check_phy_reset_block(struct e1000_hw *hw)
4303{
4304 uint32_t manc = 0;
4305 uint32_t fwsm = 0;
4306
4307 if (hw->mac_type == e1000_ich8lan) {
4308 fwsm = E1000_READ_REG(hw, FWSM);
4309 return (fwsm & E1000_FWSM_RSPCIPHY) ? E1000_SUCCESS
4310 : E1000_BLK_PHY_RESET;
4311 }
4312
4313 if (hw->mac_type > e1000_82547_rev_2)
4314 manc = E1000_READ_REG(hw, MANC);
4315 return (manc & E1000_MANC_BLK_PHY_RST_ON_IDE) ?
4316 E1000_BLK_PHY_RESET : E1000_SUCCESS;
4317}
4318
4319/***************************************************************************
4320 * Checks if the PHY configuration is done
4321 *
4322 * hw: Struct containing variables accessed by shared code
4323 *
4324 * returns: - E1000_ERR_RESET if fail to reset MAC
4325 * E1000_SUCCESS at any other case.
4326 *
4327 ***************************************************************************/
4328static int32_t
4329e1000_get_phy_cfg_done(struct e1000_hw *hw)
4330{
4331 int32_t timeout = PHY_CFG_TIMEOUT;
4332 uint32_t cfg_mask = E1000_EEPROM_CFG_DONE;
4333
4334 DEBUGFUNC();
4335
4336 switch (hw->mac_type) {
4337 default:
4338 mdelay(10);
4339 break;
Kyle Moffett987b43a2010-09-13 05:52:22 +00004340
Roy Zangaa070782009-07-31 13:34:02 +08004341 case e1000_80003es2lan:
4342 /* Separate *_CFG_DONE_* bit for each port */
Kyle Moffett987b43a2010-09-13 05:52:22 +00004343 if (e1000_is_second_port(hw))
Roy Zangaa070782009-07-31 13:34:02 +08004344 cfg_mask = E1000_EEPROM_CFG_DONE_PORT_1;
Kyle Moffett987b43a2010-09-13 05:52:22 +00004345 /* Fall Through */
4346
Roy Zangaa070782009-07-31 13:34:02 +08004347 case e1000_82571:
4348 case e1000_82572:
Marek Vasut95186062014-08-08 07:41:39 -07004349 case e1000_igb:
Roy Zangaa070782009-07-31 13:34:02 +08004350 while (timeout) {
Marek Vasut95186062014-08-08 07:41:39 -07004351 if (hw->mac_type == e1000_igb) {
4352 if (E1000_READ_REG(hw, I210_EEMNGCTL) & cfg_mask)
4353 break;
4354 } else {
4355 if (E1000_READ_REG(hw, EEMNGCTL) & cfg_mask)
4356 break;
4357 }
4358 mdelay(1);
Roy Zangaa070782009-07-31 13:34:02 +08004359 timeout--;
4360 }
4361 if (!timeout) {
4362 DEBUGOUT("MNG configuration cycle has not "
4363 "completed.\n");
4364 return -E1000_ERR_RESET;
4365 }
4366 break;
4367 }
4368
4369 return E1000_SUCCESS;
4370}
4371
4372/******************************************************************************
wdenk682011f2003-06-03 23:54:09 +00004373* Returns the PHY to the power-on reset state
4374*
4375* hw - Struct containing variables accessed by shared code
4376******************************************************************************/
Roy Zangaa070782009-07-31 13:34:02 +08004377int32_t
wdenk682011f2003-06-03 23:54:09 +00004378e1000_phy_hw_reset(struct e1000_hw *hw)
4379{
Kyle Moffett987b43a2010-09-13 05:52:22 +00004380 uint16_t swfw = E1000_SWFW_PHY0_SM;
Roy Zangaa070782009-07-31 13:34:02 +08004381 uint32_t ctrl, ctrl_ext;
4382 uint32_t led_ctrl;
4383 int32_t ret_val;
wdenk682011f2003-06-03 23:54:09 +00004384
4385 DEBUGFUNC();
4386
Roy Zangaa070782009-07-31 13:34:02 +08004387 /* In the case of the phy reset being blocked, it's not an error, we
4388 * simply return success without performing the reset. */
4389 ret_val = e1000_check_phy_reset_block(hw);
4390 if (ret_val)
4391 return E1000_SUCCESS;
4392
wdenk682011f2003-06-03 23:54:09 +00004393 DEBUGOUT("Resetting Phy...\n");
4394
4395 if (hw->mac_type > e1000_82543) {
Kyle Moffett987b43a2010-09-13 05:52:22 +00004396 if (e1000_is_second_port(hw))
Roy Zangaa070782009-07-31 13:34:02 +08004397 swfw = E1000_SWFW_PHY1_SM;
Kyle Moffett987b43a2010-09-13 05:52:22 +00004398
Roy Zangaa070782009-07-31 13:34:02 +08004399 if (e1000_swfw_sync_acquire(hw, swfw)) {
4400 DEBUGOUT("Unable to acquire swfw sync\n");
4401 return -E1000_ERR_SWFW_SYNC;
4402 }
Kyle Moffett987b43a2010-09-13 05:52:22 +00004403
wdenk682011f2003-06-03 23:54:09 +00004404 /* Read the device control register and assert the E1000_CTRL_PHY_RST
4405 * bit. Then, take it out of reset.
4406 */
4407 ctrl = E1000_READ_REG(hw, CTRL);
4408 E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PHY_RST);
4409 E1000_WRITE_FLUSH(hw);
Roy Zangaa070782009-07-31 13:34:02 +08004410
4411 if (hw->mac_type < e1000_82571)
4412 udelay(10);
4413 else
4414 udelay(100);
4415
wdenk682011f2003-06-03 23:54:09 +00004416 E1000_WRITE_REG(hw, CTRL, ctrl);
4417 E1000_WRITE_FLUSH(hw);
Roy Zangaa070782009-07-31 13:34:02 +08004418
4419 if (hw->mac_type >= e1000_82571)
4420 mdelay(10);
Tim Harvey3c63dd52015-05-19 10:01:19 -07004421
wdenk682011f2003-06-03 23:54:09 +00004422 } else {
4423 /* Read the Extended Device Control Register, assert the PHY_RESET_DIR
4424 * bit to put the PHY into reset. Then, take it out of reset.
4425 */
4426 ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
4427 ctrl_ext |= E1000_CTRL_EXT_SDP4_DIR;
4428 ctrl_ext &= ~E1000_CTRL_EXT_SDP4_DATA;
4429 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
4430 E1000_WRITE_FLUSH(hw);
4431 mdelay(10);
4432 ctrl_ext |= E1000_CTRL_EXT_SDP4_DATA;
4433 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
4434 E1000_WRITE_FLUSH(hw);
4435 }
4436 udelay(150);
Roy Zangaa070782009-07-31 13:34:02 +08004437
4438 if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
4439 /* Configure activity LED after PHY reset */
4440 led_ctrl = E1000_READ_REG(hw, LEDCTL);
4441 led_ctrl &= IGP_ACTIVITY_LED_MASK;
4442 led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
4443 E1000_WRITE_REG(hw, LEDCTL, led_ctrl);
4444 }
4445
Tim Harvey7e2d9912015-05-19 10:01:18 -07004446 e1000_swfw_sync_release(hw, swfw);
4447
Roy Zangaa070782009-07-31 13:34:02 +08004448 /* Wait for FW to finish PHY configuration. */
4449 ret_val = e1000_get_phy_cfg_done(hw);
4450 if (ret_val != E1000_SUCCESS)
4451 return ret_val;
4452
4453 return ret_val;
4454}
4455
4456/******************************************************************************
4457 * IGP phy init script - initializes the GbE PHY
4458 *
4459 * hw - Struct containing variables accessed by shared code
4460 *****************************************************************************/
4461static void
4462e1000_phy_init_script(struct e1000_hw *hw)
4463{
4464 uint32_t ret_val;
4465 uint16_t phy_saved_data;
4466 DEBUGFUNC();
4467
4468 if (hw->phy_init_script) {
4469 mdelay(20);
4470
4471 /* Save off the current value of register 0x2F5B to be
4472 * restored at the end of this routine. */
4473 ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
4474
4475 /* Disabled the PHY transmitter */
4476 e1000_write_phy_reg(hw, 0x2F5B, 0x0003);
4477
4478 mdelay(20);
4479
4480 e1000_write_phy_reg(hw, 0x0000, 0x0140);
4481
4482 mdelay(5);
4483
4484 switch (hw->mac_type) {
4485 case e1000_82541:
4486 case e1000_82547:
4487 e1000_write_phy_reg(hw, 0x1F95, 0x0001);
4488
4489 e1000_write_phy_reg(hw, 0x1F71, 0xBD21);
4490
4491 e1000_write_phy_reg(hw, 0x1F79, 0x0018);
4492
4493 e1000_write_phy_reg(hw, 0x1F30, 0x1600);
4494
4495 e1000_write_phy_reg(hw, 0x1F31, 0x0014);
4496
4497 e1000_write_phy_reg(hw, 0x1F32, 0x161C);
4498
4499 e1000_write_phy_reg(hw, 0x1F94, 0x0003);
4500
4501 e1000_write_phy_reg(hw, 0x1F96, 0x003F);
4502
4503 e1000_write_phy_reg(hw, 0x2010, 0x0008);
4504 break;
4505
4506 case e1000_82541_rev_2:
4507 case e1000_82547_rev_2:
4508 e1000_write_phy_reg(hw, 0x1F73, 0x0099);
4509 break;
4510 default:
4511 break;
4512 }
4513
4514 e1000_write_phy_reg(hw, 0x0000, 0x3300);
4515
4516 mdelay(20);
4517
4518 /* Now enable the transmitter */
Zang Roy-R6191156b13b12011-11-06 22:22:36 +00004519 if (!ret_val)
4520 e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
Roy Zangaa070782009-07-31 13:34:02 +08004521
4522 if (hw->mac_type == e1000_82547) {
4523 uint16_t fused, fine, coarse;
4524
4525 /* Move to analog registers page */
4526 e1000_read_phy_reg(hw,
4527 IGP01E1000_ANALOG_SPARE_FUSE_STATUS, &fused);
4528
4529 if (!(fused & IGP01E1000_ANALOG_SPARE_FUSE_ENABLED)) {
4530 e1000_read_phy_reg(hw,
4531 IGP01E1000_ANALOG_FUSE_STATUS, &fused);
4532
4533 fine = fused & IGP01E1000_ANALOG_FUSE_FINE_MASK;
4534 coarse = fused
4535 & IGP01E1000_ANALOG_FUSE_COARSE_MASK;
4536
4537 if (coarse >
4538 IGP01E1000_ANALOG_FUSE_COARSE_THRESH) {
4539 coarse -=
4540 IGP01E1000_ANALOG_FUSE_COARSE_10;
4541 fine -= IGP01E1000_ANALOG_FUSE_FINE_1;
4542 } else if (coarse
4543 == IGP01E1000_ANALOG_FUSE_COARSE_THRESH)
4544 fine -= IGP01E1000_ANALOG_FUSE_FINE_10;
4545
4546 fused = (fused
4547 & IGP01E1000_ANALOG_FUSE_POLY_MASK) |
4548 (fine
4549 & IGP01E1000_ANALOG_FUSE_FINE_MASK) |
4550 (coarse
4551 & IGP01E1000_ANALOG_FUSE_COARSE_MASK);
4552
4553 e1000_write_phy_reg(hw,
4554 IGP01E1000_ANALOG_FUSE_CONTROL, fused);
4555 e1000_write_phy_reg(hw,
4556 IGP01E1000_ANALOG_FUSE_BYPASS,
4557 IGP01E1000_ANALOG_FUSE_ENABLE_SW_CONTROL);
4558 }
4559 }
4560 }
wdenk682011f2003-06-03 23:54:09 +00004561}
4562
4563/******************************************************************************
4564* Resets the PHY
4565*
4566* hw - Struct containing variables accessed by shared code
4567*
Roy Zangaa070782009-07-31 13:34:02 +08004568* Sets bit 15 of the MII Control register
wdenk682011f2003-06-03 23:54:09 +00004569******************************************************************************/
Roy Zangaa070782009-07-31 13:34:02 +08004570int32_t
wdenk682011f2003-06-03 23:54:09 +00004571e1000_phy_reset(struct e1000_hw *hw)
4572{
Roy Zangaa070782009-07-31 13:34:02 +08004573 int32_t ret_val;
wdenk682011f2003-06-03 23:54:09 +00004574 uint16_t phy_data;
4575
4576 DEBUGFUNC();
4577
Roy Zangaa070782009-07-31 13:34:02 +08004578 /* In the case of the phy reset being blocked, it's not an error, we
4579 * simply return success without performing the reset. */
4580 ret_val = e1000_check_phy_reset_block(hw);
4581 if (ret_val)
4582 return E1000_SUCCESS;
4583
4584 switch (hw->phy_type) {
4585 case e1000_phy_igp:
4586 case e1000_phy_igp_2:
4587 case e1000_phy_igp_3:
4588 case e1000_phy_ife:
Marek Vasut95186062014-08-08 07:41:39 -07004589 case e1000_phy_igb:
Roy Zangaa070782009-07-31 13:34:02 +08004590 ret_val = e1000_phy_hw_reset(hw);
4591 if (ret_val)
4592 return ret_val;
4593 break;
4594 default:
4595 ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
4596 if (ret_val)
4597 return ret_val;
4598
4599 phy_data |= MII_CR_RESET;
4600 ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
4601 if (ret_val)
4602 return ret_val;
4603
4604 udelay(1);
4605 break;
wdenk682011f2003-06-03 23:54:09 +00004606 }
Roy Zangaa070782009-07-31 13:34:02 +08004607
4608 if (hw->phy_type == e1000_phy_igp || hw->phy_type == e1000_phy_igp_2)
4609 e1000_phy_init_script(hw);
4610
4611 return E1000_SUCCESS;
wdenk682011f2003-06-03 23:54:09 +00004612}
4613
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07004614static int e1000_set_phy_type (struct e1000_hw *hw)
Andre Schwarzac3315c2008-03-06 16:45:44 +01004615{
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07004616 DEBUGFUNC ();
Andre Schwarzac3315c2008-03-06 16:45:44 +01004617
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07004618 if (hw->mac_type == e1000_undefined)
4619 return -E1000_ERR_PHY_TYPE;
Andre Schwarzac3315c2008-03-06 16:45:44 +01004620
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07004621 switch (hw->phy_id) {
4622 case M88E1000_E_PHY_ID:
4623 case M88E1000_I_PHY_ID:
4624 case M88E1011_I_PHY_ID:
Roy Zangaa070782009-07-31 13:34:02 +08004625 case M88E1111_I_PHY_ID:
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07004626 hw->phy_type = e1000_phy_m88;
4627 break;
4628 case IGP01E1000_I_PHY_ID:
4629 if (hw->mac_type == e1000_82541 ||
Roy Zangaa070782009-07-31 13:34:02 +08004630 hw->mac_type == e1000_82541_rev_2 ||
4631 hw->mac_type == e1000_82547 ||
4632 hw->mac_type == e1000_82547_rev_2) {
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07004633 hw->phy_type = e1000_phy_igp;
Roy Zangaa070782009-07-31 13:34:02 +08004634 break;
4635 }
4636 case IGP03E1000_E_PHY_ID:
4637 hw->phy_type = e1000_phy_igp_3;
4638 break;
4639 case IFE_E_PHY_ID:
4640 case IFE_PLUS_E_PHY_ID:
4641 case IFE_C_E_PHY_ID:
4642 hw->phy_type = e1000_phy_ife;
4643 break;
4644 case GG82563_E_PHY_ID:
4645 if (hw->mac_type == e1000_80003es2lan) {
4646 hw->phy_type = e1000_phy_gg82563;
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07004647 break;
4648 }
Roy Zang2c2668f2011-01-21 11:29:38 +08004649 case BME1000_E_PHY_ID:
4650 hw->phy_type = e1000_phy_bm;
4651 break;
Marek Vasut95186062014-08-08 07:41:39 -07004652 case I210_I_PHY_ID:
4653 hw->phy_type = e1000_phy_igb;
4654 break;
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07004655 /* Fall Through */
4656 default:
4657 /* Should never have loaded on this device */
4658 hw->phy_type = e1000_phy_undefined;
4659 return -E1000_ERR_PHY_TYPE;
4660 }
Andre Schwarzac3315c2008-03-06 16:45:44 +01004661
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07004662 return E1000_SUCCESS;
Andre Schwarzac3315c2008-03-06 16:45:44 +01004663}
4664
wdenk682011f2003-06-03 23:54:09 +00004665/******************************************************************************
4666* Probes the expected PHY address for known PHY IDs
4667*
4668* hw - Struct containing variables accessed by shared code
4669******************************************************************************/
Roy Zangaa070782009-07-31 13:34:02 +08004670static int32_t
wdenk682011f2003-06-03 23:54:09 +00004671e1000_detect_gig_phy(struct e1000_hw *hw)
4672{
Roy Zangaa070782009-07-31 13:34:02 +08004673 int32_t phy_init_status, ret_val;
wdenk682011f2003-06-03 23:54:09 +00004674 uint16_t phy_id_high, phy_id_low;
York Sun472d5462013-04-01 11:29:11 -07004675 bool match = false;
wdenk682011f2003-06-03 23:54:09 +00004676
4677 DEBUGFUNC();
4678
Roy Zangaa070782009-07-31 13:34:02 +08004679 /* The 82571 firmware may still be configuring the PHY. In this
4680 * case, we cannot access the PHY until the configuration is done. So
4681 * we explicitly set the PHY values. */
4682 if (hw->mac_type == e1000_82571 ||
4683 hw->mac_type == e1000_82572) {
4684 hw->phy_id = IGP01E1000_I_PHY_ID;
4685 hw->phy_type = e1000_phy_igp_2;
4686 return E1000_SUCCESS;
4687 }
4688
4689 /* ESB-2 PHY reads require e1000_phy_gg82563 to be set because of a
4690 * work- around that forces PHY page 0 to be set or the reads fail.
4691 * The rest of the code in this routine uses e1000_read_phy_reg to
4692 * read the PHY ID. So for ESB-2 we need to have this set so our
4693 * reads won't fail. If the attached PHY is not a e1000_phy_gg82563,
4694 * the routines below will figure this out as well. */
4695 if (hw->mac_type == e1000_80003es2lan)
4696 hw->phy_type = e1000_phy_gg82563;
4697
wdenk682011f2003-06-03 23:54:09 +00004698 /* Read the PHY ID Registers to identify which PHY is onboard. */
Roy Zangaa070782009-07-31 13:34:02 +08004699 ret_val = e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high);
4700 if (ret_val)
4701 return ret_val;
4702
wdenk682011f2003-06-03 23:54:09 +00004703 hw->phy_id = (uint32_t) (phy_id_high << 16);
Roy Zangaa070782009-07-31 13:34:02 +08004704 udelay(20);
4705 ret_val = e1000_read_phy_reg(hw, PHY_ID2, &phy_id_low);
4706 if (ret_val)
4707 return ret_val;
4708
wdenk682011f2003-06-03 23:54:09 +00004709 hw->phy_id |= (uint32_t) (phy_id_low & PHY_REVISION_MASK);
Roy Zangaa070782009-07-31 13:34:02 +08004710 hw->phy_revision = (uint32_t) phy_id_low & ~PHY_REVISION_MASK;
wdenk682011f2003-06-03 23:54:09 +00004711
4712 switch (hw->mac_type) {
4713 case e1000_82543:
4714 if (hw->phy_id == M88E1000_E_PHY_ID)
York Sun472d5462013-04-01 11:29:11 -07004715 match = true;
wdenk682011f2003-06-03 23:54:09 +00004716 break;
4717 case e1000_82544:
4718 if (hw->phy_id == M88E1000_I_PHY_ID)
York Sun472d5462013-04-01 11:29:11 -07004719 match = true;
wdenk682011f2003-06-03 23:54:09 +00004720 break;
4721 case e1000_82540:
4722 case e1000_82545:
Roy Zangaa070782009-07-31 13:34:02 +08004723 case e1000_82545_rev_3:
wdenk682011f2003-06-03 23:54:09 +00004724 case e1000_82546:
Roy Zangaa070782009-07-31 13:34:02 +08004725 case e1000_82546_rev_3:
wdenk682011f2003-06-03 23:54:09 +00004726 if (hw->phy_id == M88E1011_I_PHY_ID)
York Sun472d5462013-04-01 11:29:11 -07004727 match = true;
wdenk682011f2003-06-03 23:54:09 +00004728 break;
Roy Zangaa070782009-07-31 13:34:02 +08004729 case e1000_82541:
Andre Schwarzac3315c2008-03-06 16:45:44 +01004730 case e1000_82541_rev_2:
Roy Zangaa070782009-07-31 13:34:02 +08004731 case e1000_82547:
4732 case e1000_82547_rev_2:
Andre Schwarzac3315c2008-03-06 16:45:44 +01004733 if(hw->phy_id == IGP01E1000_I_PHY_ID)
York Sun472d5462013-04-01 11:29:11 -07004734 match = true;
Andre Schwarzac3315c2008-03-06 16:45:44 +01004735
4736 break;
Roy Zangaa070782009-07-31 13:34:02 +08004737 case e1000_82573:
4738 if (hw->phy_id == M88E1111_I_PHY_ID)
York Sun472d5462013-04-01 11:29:11 -07004739 match = true;
Roy Zangaa070782009-07-31 13:34:02 +08004740 break;
Roy Zang2c2668f2011-01-21 11:29:38 +08004741 case e1000_82574:
4742 if (hw->phy_id == BME1000_E_PHY_ID)
York Sun472d5462013-04-01 11:29:11 -07004743 match = true;
Roy Zang2c2668f2011-01-21 11:29:38 +08004744 break;
Roy Zangaa070782009-07-31 13:34:02 +08004745 case e1000_80003es2lan:
4746 if (hw->phy_id == GG82563_E_PHY_ID)
York Sun472d5462013-04-01 11:29:11 -07004747 match = true;
Roy Zangaa070782009-07-31 13:34:02 +08004748 break;
4749 case e1000_ich8lan:
4750 if (hw->phy_id == IGP03E1000_E_PHY_ID)
York Sun472d5462013-04-01 11:29:11 -07004751 match = true;
Roy Zangaa070782009-07-31 13:34:02 +08004752 if (hw->phy_id == IFE_E_PHY_ID)
York Sun472d5462013-04-01 11:29:11 -07004753 match = true;
Roy Zangaa070782009-07-31 13:34:02 +08004754 if (hw->phy_id == IFE_PLUS_E_PHY_ID)
York Sun472d5462013-04-01 11:29:11 -07004755 match = true;
Roy Zangaa070782009-07-31 13:34:02 +08004756 if (hw->phy_id == IFE_C_E_PHY_ID)
York Sun472d5462013-04-01 11:29:11 -07004757 match = true;
Roy Zangaa070782009-07-31 13:34:02 +08004758 break;
Marek Vasut95186062014-08-08 07:41:39 -07004759 case e1000_igb:
4760 if (hw->phy_id == I210_I_PHY_ID)
4761 match = true;
4762 break;
wdenk682011f2003-06-03 23:54:09 +00004763 default:
4764 DEBUGOUT("Invalid MAC type %d\n", hw->mac_type);
4765 return -E1000_ERR_CONFIG;
4766 }
Andre Schwarzac3315c2008-03-06 16:45:44 +01004767
4768 phy_init_status = e1000_set_phy_type(hw);
4769
4770 if ((match) && (phy_init_status == E1000_SUCCESS)) {
wdenk682011f2003-06-03 23:54:09 +00004771 DEBUGOUT("PHY ID 0x%X detected\n", hw->phy_id);
4772 return 0;
4773 }
4774 DEBUGOUT("Invalid PHY ID 0x%X\n", hw->phy_id);
4775 return -E1000_ERR_PHY;
4776}
4777
Roy Zangaa070782009-07-31 13:34:02 +08004778/*****************************************************************************
4779 * Set media type and TBI compatibility.
4780 *
4781 * hw - Struct containing variables accessed by shared code
4782 * **************************************************************************/
4783void
4784e1000_set_media_type(struct e1000_hw *hw)
4785{
4786 uint32_t status;
4787
4788 DEBUGFUNC();
4789
4790 if (hw->mac_type != e1000_82543) {
4791 /* tbi_compatibility is only valid on 82543 */
York Sun472d5462013-04-01 11:29:11 -07004792 hw->tbi_compatibility_en = false;
Roy Zangaa070782009-07-31 13:34:02 +08004793 }
4794
4795 switch (hw->device_id) {
4796 case E1000_DEV_ID_82545GM_SERDES:
4797 case E1000_DEV_ID_82546GB_SERDES:
4798 case E1000_DEV_ID_82571EB_SERDES:
4799 case E1000_DEV_ID_82571EB_SERDES_DUAL:
4800 case E1000_DEV_ID_82571EB_SERDES_QUAD:
4801 case E1000_DEV_ID_82572EI_SERDES:
4802 case E1000_DEV_ID_80003ES2LAN_SERDES_DPT:
4803 hw->media_type = e1000_media_type_internal_serdes;
4804 break;
4805 default:
4806 switch (hw->mac_type) {
4807 case e1000_82542_rev2_0:
4808 case e1000_82542_rev2_1:
4809 hw->media_type = e1000_media_type_fiber;
4810 break;
4811 case e1000_ich8lan:
4812 case e1000_82573:
Roy Zang2c2668f2011-01-21 11:29:38 +08004813 case e1000_82574:
Marek Vasut95186062014-08-08 07:41:39 -07004814 case e1000_igb:
Roy Zangaa070782009-07-31 13:34:02 +08004815 /* The STATUS_TBIMODE bit is reserved or reused
4816 * for the this device.
4817 */
4818 hw->media_type = e1000_media_type_copper;
4819 break;
4820 default:
4821 status = E1000_READ_REG(hw, STATUS);
4822 if (status & E1000_STATUS_TBIMODE) {
4823 hw->media_type = e1000_media_type_fiber;
4824 /* tbi_compatibility not valid on fiber */
York Sun472d5462013-04-01 11:29:11 -07004825 hw->tbi_compatibility_en = false;
Roy Zangaa070782009-07-31 13:34:02 +08004826 } else {
4827 hw->media_type = e1000_media_type_copper;
4828 }
4829 break;
4830 }
4831 }
4832}
4833
wdenk682011f2003-06-03 23:54:09 +00004834/**
4835 * e1000_sw_init - Initialize general software structures (struct e1000_adapter)
4836 *
4837 * e1000_sw_init initializes the Adapter private data structure.
4838 * Fields are initialized based on PCI device information and
4839 * OS network device settings (MTU size).
4840 **/
4841
4842static int
Simon Glass5c5e7072015-08-19 09:33:39 -06004843e1000_sw_init(struct e1000_hw *hw)
wdenk682011f2003-06-03 23:54:09 +00004844{
wdenk682011f2003-06-03 23:54:09 +00004845 int result;
4846
4847 /* PCI config space info */
Bin Meng81dab9a2016-02-02 05:58:01 -08004848#ifdef CONFIG_DM_ETH
4849 dm_pci_read_config16(hw->pdev, PCI_VENDOR_ID, &hw->vendor_id);
4850 dm_pci_read_config16(hw->pdev, PCI_DEVICE_ID, &hw->device_id);
4851 dm_pci_read_config16(hw->pdev, PCI_SUBSYSTEM_VENDOR_ID,
4852 &hw->subsystem_vendor_id);
4853 dm_pci_read_config16(hw->pdev, PCI_SUBSYSTEM_ID, &hw->subsystem_id);
4854
4855 dm_pci_read_config8(hw->pdev, PCI_REVISION_ID, &hw->revision_id);
4856 dm_pci_read_config16(hw->pdev, PCI_COMMAND, &hw->pci_cmd_word);
4857#else
wdenk682011f2003-06-03 23:54:09 +00004858 pci_read_config_word(hw->pdev, PCI_VENDOR_ID, &hw->vendor_id);
4859 pci_read_config_word(hw->pdev, PCI_DEVICE_ID, &hw->device_id);
4860 pci_read_config_word(hw->pdev, PCI_SUBSYSTEM_VENDOR_ID,
4861 &hw->subsystem_vendor_id);
4862 pci_read_config_word(hw->pdev, PCI_SUBSYSTEM_ID, &hw->subsystem_id);
4863
4864 pci_read_config_byte(hw->pdev, PCI_REVISION_ID, &hw->revision_id);
4865 pci_read_config_word(hw->pdev, PCI_COMMAND, &hw->pci_cmd_word);
Bin Meng81dab9a2016-02-02 05:58:01 -08004866#endif
wdenk682011f2003-06-03 23:54:09 +00004867
4868 /* identify the MAC */
4869 result = e1000_set_mac_type(hw);
4870 if (result) {
Simon Glass5c5e7072015-08-19 09:33:39 -06004871 E1000_ERR(hw, "Unknown MAC Type\n");
wdenk682011f2003-06-03 23:54:09 +00004872 return result;
4873 }
4874
Roy Zangaa070782009-07-31 13:34:02 +08004875 switch (hw->mac_type) {
4876 default:
4877 break;
4878 case e1000_82541:
4879 case e1000_82547:
4880 case e1000_82541_rev_2:
4881 case e1000_82547_rev_2:
4882 hw->phy_init_script = 1;
4883 break;
4884 }
4885
wdenk682011f2003-06-03 23:54:09 +00004886 /* flow control settings */
4887 hw->fc_high_water = E1000_FC_HIGH_THRESH;
4888 hw->fc_low_water = E1000_FC_LOW_THRESH;
4889 hw->fc_pause_time = E1000_FC_PAUSE_TIME;
4890 hw->fc_send_xon = 1;
4891
4892 /* Media type - copper or fiber */
Marek Vasut95186062014-08-08 07:41:39 -07004893 hw->tbi_compatibility_en = true;
Roy Zangaa070782009-07-31 13:34:02 +08004894 e1000_set_media_type(hw);
wdenk682011f2003-06-03 23:54:09 +00004895
4896 if (hw->mac_type >= e1000_82543) {
4897 uint32_t status = E1000_READ_REG(hw, STATUS);
4898
4899 if (status & E1000_STATUS_TBIMODE) {
4900 DEBUGOUT("fiber interface\n");
4901 hw->media_type = e1000_media_type_fiber;
4902 } else {
4903 DEBUGOUT("copper interface\n");
4904 hw->media_type = e1000_media_type_copper;
4905 }
4906 } else {
4907 hw->media_type = e1000_media_type_fiber;
4908 }
4909
York Sun472d5462013-04-01 11:29:11 -07004910 hw->wait_autoneg_complete = true;
wdenk682011f2003-06-03 23:54:09 +00004911 if (hw->mac_type < e1000_82543)
4912 hw->report_tx_early = 0;
4913 else
4914 hw->report_tx_early = 1;
4915
wdenk682011f2003-06-03 23:54:09 +00004916 return E1000_SUCCESS;
4917}
4918
4919void
4920fill_rx(struct e1000_hw *hw)
4921{
4922 struct e1000_rx_desc *rd;
Minghuan Lian06e07f62015-01-22 13:21:54 +08004923 unsigned long flush_start, flush_end;
wdenk682011f2003-06-03 23:54:09 +00004924
4925 rx_last = rx_tail;
4926 rd = rx_base + rx_tail;
4927 rx_tail = (rx_tail + 1) % 8;
4928 memset(rd, 0, 16);
Minghuan Lian06e07f62015-01-22 13:21:54 +08004929 rd->buffer_addr = cpu_to_le64((unsigned long)packet);
Marek Vasut873e8e02014-08-08 07:41:38 -07004930
4931 /*
4932 * Make sure there are no stale data in WB over this area, which
4933 * might get written into the memory while the e1000 also writes
4934 * into the same memory area.
4935 */
Minghuan Lian06e07f62015-01-22 13:21:54 +08004936 invalidate_dcache_range((unsigned long)packet,
4937 (unsigned long)packet + 4096);
Marek Vasut873e8e02014-08-08 07:41:38 -07004938 /* Dump the DMA descriptor into RAM. */
Minghuan Lian06e07f62015-01-22 13:21:54 +08004939 flush_start = ((unsigned long)rd) & ~(ARCH_DMA_MINALIGN - 1);
Marek Vasut873e8e02014-08-08 07:41:38 -07004940 flush_end = flush_start + roundup(sizeof(*rd), ARCH_DMA_MINALIGN);
4941 flush_dcache_range(flush_start, flush_end);
4942
wdenk682011f2003-06-03 23:54:09 +00004943 E1000_WRITE_REG(hw, RDT, rx_tail);
4944}
4945
4946/**
4947 * e1000_configure_tx - Configure 8254x Transmit Unit after Reset
4948 * @adapter: board private structure
4949 *
4950 * Configure the Tx unit of the MAC after a reset.
4951 **/
4952
4953static void
4954e1000_configure_tx(struct e1000_hw *hw)
4955{
wdenk682011f2003-06-03 23:54:09 +00004956 unsigned long tctl;
Roy Zangaa070782009-07-31 13:34:02 +08004957 unsigned long tipg, tarc;
4958 uint32_t ipgr1, ipgr2;
wdenk682011f2003-06-03 23:54:09 +00004959
Bin Meng1d8a0782015-08-26 06:17:27 -07004960 E1000_WRITE_REG(hw, TDBAL, lower_32_bits((unsigned long)tx_base));
4961 E1000_WRITE_REG(hw, TDBAH, upper_32_bits((unsigned long)tx_base));
wdenk682011f2003-06-03 23:54:09 +00004962
4963 E1000_WRITE_REG(hw, TDLEN, 128);
4964
4965 /* Setup the HW Tx Head and Tail descriptor pointers */
4966 E1000_WRITE_REG(hw, TDH, 0);
4967 E1000_WRITE_REG(hw, TDT, 0);
4968 tx_tail = 0;
4969
4970 /* Set the default values for the Tx Inter Packet Gap timer */
Roy Zangaa070782009-07-31 13:34:02 +08004971 if (hw->mac_type <= e1000_82547_rev_2 &&
4972 (hw->media_type == e1000_media_type_fiber ||
4973 hw->media_type == e1000_media_type_internal_serdes))
4974 tipg = DEFAULT_82543_TIPG_IPGT_FIBER;
4975 else
4976 tipg = DEFAULT_82543_TIPG_IPGT_COPPER;
4977
4978 /* Set the default values for the Tx Inter Packet Gap timer */
wdenk682011f2003-06-03 23:54:09 +00004979 switch (hw->mac_type) {
4980 case e1000_82542_rev2_0:
4981 case e1000_82542_rev2_1:
4982 tipg = DEFAULT_82542_TIPG_IPGT;
Roy Zangaa070782009-07-31 13:34:02 +08004983 ipgr1 = DEFAULT_82542_TIPG_IPGR1;
4984 ipgr2 = DEFAULT_82542_TIPG_IPGR2;
4985 break;
4986 case e1000_80003es2lan:
4987 ipgr1 = DEFAULT_82543_TIPG_IPGR1;
4988 ipgr2 = DEFAULT_80003ES2LAN_TIPG_IPGR2;
wdenk682011f2003-06-03 23:54:09 +00004989 break;
4990 default:
Roy Zangaa070782009-07-31 13:34:02 +08004991 ipgr1 = DEFAULT_82543_TIPG_IPGR1;
4992 ipgr2 = DEFAULT_82543_TIPG_IPGR2;
4993 break;
wdenk682011f2003-06-03 23:54:09 +00004994 }
Roy Zangaa070782009-07-31 13:34:02 +08004995 tipg |= ipgr1 << E1000_TIPG_IPGR1_SHIFT;
4996 tipg |= ipgr2 << E1000_TIPG_IPGR2_SHIFT;
wdenk682011f2003-06-03 23:54:09 +00004997 E1000_WRITE_REG(hw, TIPG, tipg);
wdenk682011f2003-06-03 23:54:09 +00004998 /* Program the Transmit Control Register */
4999 tctl = E1000_READ_REG(hw, TCTL);
5000 tctl &= ~E1000_TCTL_CT;
5001 tctl |= E1000_TCTL_EN | E1000_TCTL_PSP |
5002 (E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT);
Roy Zangaa070782009-07-31 13:34:02 +08005003
5004 if (hw->mac_type == e1000_82571 || hw->mac_type == e1000_82572) {
5005 tarc = E1000_READ_REG(hw, TARC0);
5006 /* set the speed mode bit, we'll clear it if we're not at
5007 * gigabit link later */
5008 /* git bit can be set to 1*/
5009 } else if (hw->mac_type == e1000_80003es2lan) {
5010 tarc = E1000_READ_REG(hw, TARC0);
5011 tarc |= 1;
5012 E1000_WRITE_REG(hw, TARC0, tarc);
5013 tarc = E1000_READ_REG(hw, TARC1);
5014 tarc |= 1;
5015 E1000_WRITE_REG(hw, TARC1, tarc);
5016 }
5017
wdenk682011f2003-06-03 23:54:09 +00005018
5019 e1000_config_collision_dist(hw);
Roy Zangaa070782009-07-31 13:34:02 +08005020 /* Setup Transmit Descriptor Settings for eop descriptor */
5021 hw->txd_cmd = E1000_TXD_CMD_EOP | E1000_TXD_CMD_IFCS;
wdenk682011f2003-06-03 23:54:09 +00005022
Roy Zangaa070782009-07-31 13:34:02 +08005023 /* Need to set up RS bit */
5024 if (hw->mac_type < e1000_82543)
5025 hw->txd_cmd |= E1000_TXD_CMD_RPS;
wdenk682011f2003-06-03 23:54:09 +00005026 else
Roy Zangaa070782009-07-31 13:34:02 +08005027 hw->txd_cmd |= E1000_TXD_CMD_RS;
Marek Vasut95186062014-08-08 07:41:39 -07005028
5029
5030 if (hw->mac_type == e1000_igb) {
5031 E1000_WRITE_REG(hw, TCTL_EXT, 0x42 << 10);
5032
5033 uint32_t reg_txdctl = E1000_READ_REG(hw, TXDCTL);
5034 reg_txdctl |= 1 << 25;
5035 E1000_WRITE_REG(hw, TXDCTL, reg_txdctl);
5036 mdelay(20);
5037 }
5038
5039
5040
Roy Zangaa070782009-07-31 13:34:02 +08005041 E1000_WRITE_REG(hw, TCTL, tctl);
Marek Vasut95186062014-08-08 07:41:39 -07005042
5043
wdenk682011f2003-06-03 23:54:09 +00005044}
5045
5046/**
5047 * e1000_setup_rctl - configure the receive control register
5048 * @adapter: Board private structure
5049 **/
5050static void
5051e1000_setup_rctl(struct e1000_hw *hw)
5052{
5053 uint32_t rctl;
5054
5055 rctl = E1000_READ_REG(hw, RCTL);
5056
5057 rctl &= ~(3 << E1000_RCTL_MO_SHIFT);
5058
Roy Zangaa070782009-07-31 13:34:02 +08005059 rctl |= E1000_RCTL_EN | E1000_RCTL_BAM | E1000_RCTL_LBM_NO
5060 | E1000_RCTL_RDMTS_HALF; /* |
5061 (hw.mc_filter_type << E1000_RCTL_MO_SHIFT); */
wdenk682011f2003-06-03 23:54:09 +00005062
5063 if (hw->tbi_compatibility_on == 1)
5064 rctl |= E1000_RCTL_SBP;
5065 else
5066 rctl &= ~E1000_RCTL_SBP;
5067
5068 rctl &= ~(E1000_RCTL_SZ_4096);
wdenk682011f2003-06-03 23:54:09 +00005069 rctl |= E1000_RCTL_SZ_2048;
5070 rctl &= ~(E1000_RCTL_BSEX | E1000_RCTL_LPE);
wdenk682011f2003-06-03 23:54:09 +00005071 E1000_WRITE_REG(hw, RCTL, rctl);
5072}
5073
5074/**
5075 * e1000_configure_rx - Configure 8254x Receive Unit after Reset
5076 * @adapter: board private structure
5077 *
5078 * Configure the Rx unit of the MAC after a reset.
5079 **/
5080static void
5081e1000_configure_rx(struct e1000_hw *hw)
5082{
Roy Zangaa070782009-07-31 13:34:02 +08005083 unsigned long rctl, ctrl_ext;
wdenk682011f2003-06-03 23:54:09 +00005084 rx_tail = 0;
Bin Meng1d8a0782015-08-26 06:17:27 -07005085
wdenk682011f2003-06-03 23:54:09 +00005086 /* make sure receives are disabled while setting up the descriptors */
5087 rctl = E1000_READ_REG(hw, RCTL);
5088 E1000_WRITE_REG(hw, RCTL, rctl & ~E1000_RCTL_EN);
wdenk682011f2003-06-03 23:54:09 +00005089 if (hw->mac_type >= e1000_82540) {
wdenk682011f2003-06-03 23:54:09 +00005090 /* Set the interrupt throttling rate. Value is calculated
5091 * as DEFAULT_ITR = 1/(MAX_INTS_PER_SEC * 256ns) */
Wolfgang Denk1aeed8d2008-04-13 09:59:26 -07005092#define MAX_INTS_PER_SEC 8000
5093#define DEFAULT_ITR 1000000000/(MAX_INTS_PER_SEC * 256)
wdenk682011f2003-06-03 23:54:09 +00005094 E1000_WRITE_REG(hw, ITR, DEFAULT_ITR);
5095 }
5096
Roy Zangaa070782009-07-31 13:34:02 +08005097 if (hw->mac_type >= e1000_82571) {
5098 ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
5099 /* Reset delay timers after every interrupt */
5100 ctrl_ext |= E1000_CTRL_EXT_INT_TIMER_CLR;
5101 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
5102 E1000_WRITE_FLUSH(hw);
5103 }
wdenk682011f2003-06-03 23:54:09 +00005104 /* Setup the Base and Length of the Rx Descriptor Ring */
Bin Meng1d8a0782015-08-26 06:17:27 -07005105 E1000_WRITE_REG(hw, RDBAL, lower_32_bits((unsigned long)rx_base));
5106 E1000_WRITE_REG(hw, RDBAH, upper_32_bits((unsigned long)rx_base));
wdenk682011f2003-06-03 23:54:09 +00005107
5108 E1000_WRITE_REG(hw, RDLEN, 128);
5109
5110 /* Setup the HW Rx Head and Tail Descriptor Pointers */
5111 E1000_WRITE_REG(hw, RDH, 0);
5112 E1000_WRITE_REG(hw, RDT, 0);
wdenk682011f2003-06-03 23:54:09 +00005113 /* Enable Receives */
5114
Marek Vasut95186062014-08-08 07:41:39 -07005115 if (hw->mac_type == e1000_igb) {
5116
5117 uint32_t reg_rxdctl = E1000_READ_REG(hw, RXDCTL);
5118 reg_rxdctl |= 1 << 25;
5119 E1000_WRITE_REG(hw, RXDCTL, reg_rxdctl);
5120 mdelay(20);
5121 }
5122
wdenk682011f2003-06-03 23:54:09 +00005123 E1000_WRITE_REG(hw, RCTL, rctl);
Marek Vasut95186062014-08-08 07:41:39 -07005124
wdenk682011f2003-06-03 23:54:09 +00005125 fill_rx(hw);
5126}
5127
5128/**************************************************************************
5129POLL - Wait for a frame
5130***************************************************************************/
5131static int
Simon Glass5c5e7072015-08-19 09:33:39 -06005132_e1000_poll(struct e1000_hw *hw)
wdenk682011f2003-06-03 23:54:09 +00005133{
wdenk682011f2003-06-03 23:54:09 +00005134 struct e1000_rx_desc *rd;
Minghuan Lian06e07f62015-01-22 13:21:54 +08005135 unsigned long inval_start, inval_end;
Marek Vasut873e8e02014-08-08 07:41:38 -07005136 uint32_t len;
5137
wdenk682011f2003-06-03 23:54:09 +00005138 /* return true if there's an ethernet packet ready to read */
5139 rd = rx_base + rx_last;
Marek Vasut873e8e02014-08-08 07:41:38 -07005140
5141 /* Re-load the descriptor from RAM. */
Minghuan Lian06e07f62015-01-22 13:21:54 +08005142 inval_start = ((unsigned long)rd) & ~(ARCH_DMA_MINALIGN - 1);
Marek Vasut873e8e02014-08-08 07:41:38 -07005143 inval_end = inval_start + roundup(sizeof(*rd), ARCH_DMA_MINALIGN);
5144 invalidate_dcache_range(inval_start, inval_end);
5145
Miao Yana40b2df2015-12-21 02:07:02 -08005146 if (!(rd->status & E1000_RXD_STAT_DD))
wdenk682011f2003-06-03 23:54:09 +00005147 return 0;
Minghuan Lian5abf13e2015-03-19 09:43:51 -07005148 /* DEBUGOUT("recv: packet len=%d\n", rd->length); */
Marek Vasut873e8e02014-08-08 07:41:38 -07005149 /* Packet received, make sure the data are re-loaded from RAM. */
Miao Yana40b2df2015-12-21 02:07:02 -08005150 len = le16_to_cpu(rd->length);
Minghuan Lian06e07f62015-01-22 13:21:54 +08005151 invalidate_dcache_range((unsigned long)packet,
5152 (unsigned long)packet +
5153 roundup(len, ARCH_DMA_MINALIGN));
Simon Glass5c5e7072015-08-19 09:33:39 -06005154 return len;
wdenk682011f2003-06-03 23:54:09 +00005155}
5156
Simon Glass5c5e7072015-08-19 09:33:39 -06005157static int _e1000_transmit(struct e1000_hw *hw, void *txpacket, int length)
wdenk682011f2003-06-03 23:54:09 +00005158{
Marek Vasut873e8e02014-08-08 07:41:38 -07005159 void *nv_packet = (void *)txpacket;
wdenk682011f2003-06-03 23:54:09 +00005160 struct e1000_tx_desc *txp;
5161 int i = 0;
Minghuan Lian06e07f62015-01-22 13:21:54 +08005162 unsigned long flush_start, flush_end;
wdenk682011f2003-06-03 23:54:09 +00005163
5164 txp = tx_base + tx_tail;
5165 tx_tail = (tx_tail + 1) % 8;
5166
Wolfgang Denk8aa858c2010-11-22 09:48:45 +01005167 txp->buffer_addr = cpu_to_le64(virt_to_bus(hw->pdev, nv_packet));
Roy Zangaa070782009-07-31 13:34:02 +08005168 txp->lower.data = cpu_to_le32(hw->txd_cmd | length);
wdenk682011f2003-06-03 23:54:09 +00005169 txp->upper.data = 0;
Marek Vasut873e8e02014-08-08 07:41:38 -07005170
5171 /* Dump the packet into RAM so e1000 can pick them. */
Minghuan Lian06e07f62015-01-22 13:21:54 +08005172 flush_dcache_range((unsigned long)nv_packet,
5173 (unsigned long)nv_packet +
5174 roundup(length, ARCH_DMA_MINALIGN));
Marek Vasut873e8e02014-08-08 07:41:38 -07005175 /* Dump the descriptor into RAM as well. */
Minghuan Lian06e07f62015-01-22 13:21:54 +08005176 flush_start = ((unsigned long)txp) & ~(ARCH_DMA_MINALIGN - 1);
Marek Vasut873e8e02014-08-08 07:41:38 -07005177 flush_end = flush_start + roundup(sizeof(*txp), ARCH_DMA_MINALIGN);
5178 flush_dcache_range(flush_start, flush_end);
5179
wdenk682011f2003-06-03 23:54:09 +00005180 E1000_WRITE_REG(hw, TDT, tx_tail);
5181
Roy Zangaa070782009-07-31 13:34:02 +08005182 E1000_WRITE_FLUSH(hw);
Marek Vasut873e8e02014-08-08 07:41:38 -07005183 while (1) {
5184 invalidate_dcache_range(flush_start, flush_end);
5185 if (le32_to_cpu(txp->upper.data) & E1000_TXD_STAT_DD)
5186 break;
wdenk682011f2003-06-03 23:54:09 +00005187 if (i++ > TOUT_LOOP) {
5188 DEBUGOUT("e1000: tx timeout\n");
5189 return 0;
5190 }
5191 udelay(10); /* give the nic a chance to write to the register */
5192 }
5193 return 1;
5194}
5195
wdenk682011f2003-06-03 23:54:09 +00005196static void
Simon Glass5c5e7072015-08-19 09:33:39 -06005197_e1000_disable(struct e1000_hw *hw)
wdenk682011f2003-06-03 23:54:09 +00005198{
wdenk682011f2003-06-03 23:54:09 +00005199 /* Turn off the ethernet interface */
5200 E1000_WRITE_REG(hw, RCTL, 0);
5201 E1000_WRITE_REG(hw, TCTL, 0);
5202
5203 /* Clear the transmit ring */
5204 E1000_WRITE_REG(hw, TDH, 0);
5205 E1000_WRITE_REG(hw, TDT, 0);
5206
5207 /* Clear the receive ring */
5208 E1000_WRITE_REG(hw, RDH, 0);
5209 E1000_WRITE_REG(hw, RDT, 0);
5210
wdenk682011f2003-06-03 23:54:09 +00005211 mdelay(10);
wdenk682011f2003-06-03 23:54:09 +00005212}
5213
Simon Glass5c5e7072015-08-19 09:33:39 -06005214/*reset function*/
5215static inline int
5216e1000_reset(struct e1000_hw *hw, unsigned char enetaddr[6])
wdenk682011f2003-06-03 23:54:09 +00005217{
Simon Glass5c5e7072015-08-19 09:33:39 -06005218 e1000_reset_hw(hw);
5219 if (hw->mac_type >= e1000_82544)
5220 E1000_WRITE_REG(hw, WUC, 0);
5221
5222 return e1000_init_hw(hw, enetaddr);
5223}
5224
5225static int
5226_e1000_init(struct e1000_hw *hw, unsigned char enetaddr[6])
5227{
wdenk682011f2003-06-03 23:54:09 +00005228 int ret_val = 0;
5229
Simon Glass5c5e7072015-08-19 09:33:39 -06005230 ret_val = e1000_reset(hw, enetaddr);
wdenk682011f2003-06-03 23:54:09 +00005231 if (ret_val < 0) {
5232 if ((ret_val == -E1000_ERR_NOLINK) ||
5233 (ret_val == -E1000_ERR_TIMEOUT)) {
Simon Glass5c5e7072015-08-19 09:33:39 -06005234 E1000_ERR(hw, "Valid Link not detected: %d\n", ret_val);
wdenk682011f2003-06-03 23:54:09 +00005235 } else {
Simon Glass5c5e7072015-08-19 09:33:39 -06005236 E1000_ERR(hw, "Hardware Initialization Failed\n");
wdenk682011f2003-06-03 23:54:09 +00005237 }
Simon Glass5c5e7072015-08-19 09:33:39 -06005238 return ret_val;
wdenk682011f2003-06-03 23:54:09 +00005239 }
5240 e1000_configure_tx(hw);
5241 e1000_setup_rctl(hw);
5242 e1000_configure_rx(hw);
Simon Glass5c5e7072015-08-19 09:33:39 -06005243 return 0;
wdenk682011f2003-06-03 23:54:09 +00005244}
5245
Roy Zangaa070782009-07-31 13:34:02 +08005246/******************************************************************************
5247 * Gets the current PCI bus type of hardware
5248 *
5249 * hw - Struct containing variables accessed by shared code
5250 *****************************************************************************/
5251void e1000_get_bus_type(struct e1000_hw *hw)
5252{
5253 uint32_t status;
5254
5255 switch (hw->mac_type) {
5256 case e1000_82542_rev2_0:
5257 case e1000_82542_rev2_1:
5258 hw->bus_type = e1000_bus_type_pci;
5259 break;
5260 case e1000_82571:
5261 case e1000_82572:
5262 case e1000_82573:
Roy Zang2c2668f2011-01-21 11:29:38 +08005263 case e1000_82574:
Roy Zangaa070782009-07-31 13:34:02 +08005264 case e1000_80003es2lan:
Roy Zangaa070782009-07-31 13:34:02 +08005265 case e1000_ich8lan:
Marek Vasut95186062014-08-08 07:41:39 -07005266 case e1000_igb:
Roy Zangaa070782009-07-31 13:34:02 +08005267 hw->bus_type = e1000_bus_type_pci_express;
5268 break;
5269 default:
5270 status = E1000_READ_REG(hw, STATUS);
5271 hw->bus_type = (status & E1000_STATUS_PCIX_MODE) ?
5272 e1000_bus_type_pcix : e1000_bus_type_pci;
5273 break;
5274 }
5275}
5276
Simon Glassc6d80a12015-08-19 09:33:40 -06005277#ifndef CONFIG_DM_ETH
Kyle Moffettce5207e2011-10-18 11:05:29 +00005278/* A list of all registered e1000 devices */
5279static LIST_HEAD(e1000_hw_list);
Simon Glassc6d80a12015-08-19 09:33:40 -06005280#endif
Kyle Moffettce5207e2011-10-18 11:05:29 +00005281
Bin Meng81dab9a2016-02-02 05:58:01 -08005282#ifdef CONFIG_DM_ETH
5283static int e1000_init_one(struct e1000_hw *hw, int cardnum,
5284 struct udevice *devno, unsigned char enetaddr[6])
5285#else
Simon Glass5c5e7072015-08-19 09:33:39 -06005286static int e1000_init_one(struct e1000_hw *hw, int cardnum, pci_dev_t devno,
5287 unsigned char enetaddr[6])
Bin Meng81dab9a2016-02-02 05:58:01 -08005288#endif
Simon Glass5c5e7072015-08-19 09:33:39 -06005289{
5290 u32 val;
5291
5292 /* Assign the passed-in values */
Bin Meng81dab9a2016-02-02 05:58:01 -08005293#ifdef CONFIG_DM_ETH
Simon Glass5c5e7072015-08-19 09:33:39 -06005294 hw->pdev = devno;
Bin Meng81dab9a2016-02-02 05:58:01 -08005295#else
5296 hw->pdev = devno;
5297#endif
Simon Glass5c5e7072015-08-19 09:33:39 -06005298 hw->cardnum = cardnum;
5299
5300 /* Print a debug message with the IO base address */
Bin Meng81dab9a2016-02-02 05:58:01 -08005301#ifdef CONFIG_DM_ETH
5302 dm_pci_read_config32(devno, PCI_BASE_ADDRESS_0, &val);
5303#else
Simon Glass5c5e7072015-08-19 09:33:39 -06005304 pci_read_config_dword(devno, PCI_BASE_ADDRESS_0, &val);
Bin Meng81dab9a2016-02-02 05:58:01 -08005305#endif
Simon Glass5c5e7072015-08-19 09:33:39 -06005306 E1000_DBG(hw, "iobase 0x%08x\n", val & 0xfffffff0);
5307
5308 /* Try to enable I/O accesses and bus-mastering */
5309 val = PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER;
Bin Meng81dab9a2016-02-02 05:58:01 -08005310#ifdef CONFIG_DM_ETH
5311 dm_pci_write_config32(devno, PCI_COMMAND, val);
5312#else
Simon Glass5c5e7072015-08-19 09:33:39 -06005313 pci_write_config_dword(devno, PCI_COMMAND, val);
Bin Meng81dab9a2016-02-02 05:58:01 -08005314#endif
Simon Glass5c5e7072015-08-19 09:33:39 -06005315
5316 /* Make sure it worked */
Bin Meng81dab9a2016-02-02 05:58:01 -08005317#ifdef CONFIG_DM_ETH
5318 dm_pci_read_config32(devno, PCI_COMMAND, &val);
5319#else
Simon Glass5c5e7072015-08-19 09:33:39 -06005320 pci_read_config_dword(devno, PCI_COMMAND, &val);
Bin Meng81dab9a2016-02-02 05:58:01 -08005321#endif
Simon Glass5c5e7072015-08-19 09:33:39 -06005322 if (!(val & PCI_COMMAND_MEMORY)) {
5323 E1000_ERR(hw, "Can't enable I/O memory\n");
5324 return -ENOSPC;
5325 }
5326 if (!(val & PCI_COMMAND_MASTER)) {
5327 E1000_ERR(hw, "Can't enable bus-mastering\n");
5328 return -EPERM;
5329 }
5330
5331 /* Are these variables needed? */
5332 hw->fc = e1000_fc_default;
5333 hw->original_fc = e1000_fc_default;
5334 hw->autoneg_failed = 0;
5335 hw->autoneg = 1;
5336 hw->get_link_status = true;
5337#ifndef CONFIG_E1000_NO_NVM
5338 hw->eeprom_semaphore_present = true;
5339#endif
Bin Meng81dab9a2016-02-02 05:58:01 -08005340#ifdef CONFIG_DM_ETH
5341 hw->hw_addr = dm_pci_map_bar(devno, PCI_BASE_ADDRESS_0,
5342 PCI_REGION_MEM);
5343#else
Simon Glass5c5e7072015-08-19 09:33:39 -06005344 hw->hw_addr = pci_map_bar(devno, PCI_BASE_ADDRESS_0,
5345 PCI_REGION_MEM);
Bin Meng81dab9a2016-02-02 05:58:01 -08005346#endif
Simon Glass5c5e7072015-08-19 09:33:39 -06005347 hw->mac_type = e1000_undefined;
5348
5349 /* MAC and Phy settings */
5350 if (e1000_sw_init(hw) < 0) {
5351 E1000_ERR(hw, "Software init failed\n");
5352 return -EIO;
5353 }
5354 if (e1000_check_phy_reset_block(hw))
5355 E1000_ERR(hw, "PHY Reset is blocked!\n");
5356
5357 /* Basic init was OK, reset the hardware and allow SPI access */
5358 e1000_reset_hw(hw);
5359
5360#ifndef CONFIG_E1000_NO_NVM
5361 /* Validate the EEPROM and get chipset information */
Simon Glass5c5e7072015-08-19 09:33:39 -06005362 if (e1000_init_eeprom_params(hw)) {
5363 E1000_ERR(hw, "EEPROM is invalid!\n");
5364 return -EINVAL;
5365 }
5366 if ((E1000_READ_REG(hw, I210_EECD) & E1000_EECD_FLUPD) &&
5367 e1000_validate_eeprom_checksum(hw))
5368 return -ENXIO;
Simon Glass5c5e7072015-08-19 09:33:39 -06005369 e1000_read_mac_addr(hw, enetaddr);
5370#endif
5371 e1000_get_bus_type(hw);
5372
5373#ifndef CONFIG_E1000_NO_NVM
5374 printf("e1000: %02x:%02x:%02x:%02x:%02x:%02x\n ",
5375 enetaddr[0], enetaddr[1], enetaddr[2],
5376 enetaddr[3], enetaddr[4], enetaddr[5]);
5377#else
5378 memset(enetaddr, 0, 6);
5379 printf("e1000: no NVM\n");
5380#endif
5381
5382 return 0;
5383}
5384
5385/* Put the name of a device in a string */
5386static void e1000_name(char *str, int cardnum)
5387{
5388 sprintf(str, "e1000#%u", cardnum);
5389}
5390
Simon Glassc6d80a12015-08-19 09:33:40 -06005391#ifndef CONFIG_DM_ETH
Simon Glass5c5e7072015-08-19 09:33:39 -06005392/**************************************************************************
5393TRANSMIT - Transmit a frame
5394***************************************************************************/
5395static int e1000_transmit(struct eth_device *nic, void *txpacket, int length)
5396{
5397 struct e1000_hw *hw = nic->priv;
5398
5399 return _e1000_transmit(hw, txpacket, length);
5400}
5401
5402/**************************************************************************
5403DISABLE - Turn off ethernet interface
5404***************************************************************************/
5405static void
5406e1000_disable(struct eth_device *nic)
5407{
5408 struct e1000_hw *hw = nic->priv;
5409
5410 _e1000_disable(hw);
5411}
5412
5413/**************************************************************************
5414INIT - set up ethernet interface(s)
5415***************************************************************************/
5416static int
5417e1000_init(struct eth_device *nic, bd_t *bis)
5418{
5419 struct e1000_hw *hw = nic->priv;
5420
5421 return _e1000_init(hw, nic->enetaddr);
5422}
5423
5424static int
5425e1000_poll(struct eth_device *nic)
5426{
5427 struct e1000_hw *hw = nic->priv;
5428 int len;
5429
5430 len = _e1000_poll(hw);
5431 if (len) {
5432 net_process_received_packet((uchar *)packet, len);
5433 fill_rx(hw);
5434 }
5435
5436 return len ? 1 : 0;
5437}
5438
wdenk682011f2003-06-03 23:54:09 +00005439/**************************************************************************
5440PROBE - Look for an adapter, this routine's visible to the outside
5441You should omit the last argument struct pci_device * for a non-PCI NIC
5442***************************************************************************/
5443int
5444e1000_initialize(bd_t * bis)
5445{
Kyle Moffettd60626f82011-10-18 11:05:26 +00005446 unsigned int i;
wdenk682011f2003-06-03 23:54:09 +00005447 pci_dev_t devno;
Simon Glass5c5e7072015-08-19 09:33:39 -06005448 int ret;
wdenk682011f2003-06-03 23:54:09 +00005449
Timur Tabif81ecb52009-08-17 15:55:38 -05005450 DEBUGFUNC();
5451
Kyle Moffettd60626f82011-10-18 11:05:26 +00005452 /* Find and probe all the matching PCI devices */
5453 for (i = 0; (devno = pci_find_devices(e1000_supported, i)) >= 0; i++) {
Kyle Moffettd60626f82011-10-18 11:05:26 +00005454 /*
5455 * These will never get freed due to errors, this allows us to
Bin Menga1875592016-02-05 19:30:11 -08005456 * perform SPI EEPROM programming from U-Boot, for example.
Kyle Moffettd60626f82011-10-18 11:05:26 +00005457 */
5458 struct eth_device *nic = malloc(sizeof(*nic));
5459 struct e1000_hw *hw = malloc(sizeof(*hw));
5460 if (!nic || !hw) {
5461 printf("e1000#%u: Out of Memory!\n", i);
Kumar Gala4b29bdb2010-11-12 04:13:06 -06005462 free(nic);
Kyle Moffettd60626f82011-10-18 11:05:26 +00005463 free(hw);
5464 continue;
Kumar Gala4b29bdb2010-11-12 04:13:06 -06005465 }
5466
Kyle Moffettd60626f82011-10-18 11:05:26 +00005467 /* Make sure all of the fields are initially zeroed */
Matthew McClintockf7ac99f2010-11-15 18:02:53 -06005468 memset(nic, 0, sizeof(*nic));
Kumar Gala4b29bdb2010-11-12 04:13:06 -06005469 memset(hw, 0, sizeof(*hw));
wdenk682011f2003-06-03 23:54:09 +00005470 nic->priv = hw;
wdenk682011f2003-06-03 23:54:09 +00005471
Kyle Moffettd60626f82011-10-18 11:05:26 +00005472 /* Generate a card name */
Simon Glass5c5e7072015-08-19 09:33:39 -06005473 e1000_name(nic->name, i);
5474 hw->name = nic->name;
Kyle Moffettd60626f82011-10-18 11:05:26 +00005475
Simon Glass5c5e7072015-08-19 09:33:39 -06005476 ret = e1000_init_one(hw, i, devno, nic->enetaddr);
5477 if (ret)
Kyle Moffettd60626f82011-10-18 11:05:26 +00005478 continue;
Kyle Moffettce5207e2011-10-18 11:05:29 +00005479 list_add_tail(&hw->list_node, &e1000_hw_list);
Kyle Moffettd60626f82011-10-18 11:05:26 +00005480
Simon Glass5c5e7072015-08-19 09:33:39 -06005481 hw->nic = nic;
wdenk682011f2003-06-03 23:54:09 +00005482
Kyle Moffettd60626f82011-10-18 11:05:26 +00005483 /* Set up the function pointers and register the device */
wdenk682011f2003-06-03 23:54:09 +00005484 nic->init = e1000_init;
5485 nic->recv = e1000_poll;
5486 nic->send = e1000_transmit;
5487 nic->halt = e1000_disable;
wdenk682011f2003-06-03 23:54:09 +00005488 eth_register(nic);
wdenk682011f2003-06-03 23:54:09 +00005489 }
Kyle Moffettd60626f82011-10-18 11:05:26 +00005490
5491 return i;
wdenk682011f2003-06-03 23:54:09 +00005492}
Kyle Moffettce5207e2011-10-18 11:05:29 +00005493
5494struct e1000_hw *e1000_find_card(unsigned int cardnum)
5495{
5496 struct e1000_hw *hw;
5497
5498 list_for_each_entry(hw, &e1000_hw_list, list_node)
5499 if (hw->cardnum == cardnum)
5500 return hw;
5501
5502 return NULL;
5503}
Simon Glassc6d80a12015-08-19 09:33:40 -06005504#endif /* !CONFIG_DM_ETH */
Kyle Moffettce5207e2011-10-18 11:05:29 +00005505
5506#ifdef CONFIG_CMD_E1000
5507static int do_e1000(cmd_tbl_t *cmdtp, int flag,
5508 int argc, char * const argv[])
5509{
Simon Glass5c5e7072015-08-19 09:33:39 -06005510 unsigned char *mac = NULL;
Simon Glassc6d80a12015-08-19 09:33:40 -06005511#ifdef CONFIG_DM_ETH
5512 struct eth_pdata *plat;
5513 struct udevice *dev;
5514 char name[30];
5515 int ret;
5516#else
Kyle Moffettce5207e2011-10-18 11:05:29 +00005517 struct e1000_hw *hw;
Simon Glassc6d80a12015-08-19 09:33:40 -06005518#endif
5519 int cardnum;
Kyle Moffettce5207e2011-10-18 11:05:29 +00005520
5521 if (argc < 3) {
5522 cmd_usage(cmdtp);
5523 return 1;
5524 }
5525
5526 /* Make sure we can find the requested e1000 card */
Simon Glass5c5e7072015-08-19 09:33:39 -06005527 cardnum = simple_strtoul(argv[1], NULL, 10);
Simon Glassc6d80a12015-08-19 09:33:40 -06005528#ifdef CONFIG_DM_ETH
5529 e1000_name(name, cardnum);
5530 ret = uclass_get_device_by_name(UCLASS_ETH, name, &dev);
5531 if (!ret) {
5532 plat = dev_get_platdata(dev);
5533 mac = plat->enetaddr;
5534 }
5535#else
Simon Glass5c5e7072015-08-19 09:33:39 -06005536 hw = e1000_find_card(cardnum);
5537 if (hw)
5538 mac = hw->nic->enetaddr;
Simon Glassc6d80a12015-08-19 09:33:40 -06005539#endif
Simon Glass5c5e7072015-08-19 09:33:39 -06005540 if (!mac) {
Kyle Moffettce5207e2011-10-18 11:05:29 +00005541 printf("e1000: ERROR: No such device: e1000#%s\n", argv[1]);
5542 return 1;
5543 }
5544
5545 if (!strcmp(argv[2], "print-mac-address")) {
Kyle Moffettce5207e2011-10-18 11:05:29 +00005546 printf("%02x:%02x:%02x:%02x:%02x:%02x\n",
5547 mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]);
5548 return 0;
5549 }
5550
5551#ifdef CONFIG_E1000_SPI
5552 /* Handle the "SPI" subcommand */
5553 if (!strcmp(argv[2], "spi"))
5554 return do_e1000_spi(cmdtp, hw, argc - 3, argv + 3);
5555#endif
5556
5557 cmd_usage(cmdtp);
5558 return 1;
5559}
5560
5561U_BOOT_CMD(
5562 e1000, 7, 0, do_e1000,
5563 "Intel e1000 controller management",
5564 /* */"<card#> print-mac-address\n"
5565#ifdef CONFIG_E1000_SPI
5566 "e1000 <card#> spi show [<offset> [<length>]]\n"
5567 "e1000 <card#> spi dump <addr> <offset> <length>\n"
5568 "e1000 <card#> spi program <addr> <offset> <length>\n"
5569 "e1000 <card#> spi checksum [update]\n"
5570#endif
5571 " - Manage the Intel E1000 PCI device"
5572);
5573#endif /* not CONFIG_CMD_E1000 */
Simon Glassc6d80a12015-08-19 09:33:40 -06005574
5575#ifdef CONFIG_DM_ETH
5576static int e1000_eth_start(struct udevice *dev)
5577{
5578 struct eth_pdata *plat = dev_get_platdata(dev);
5579 struct e1000_hw *hw = dev_get_priv(dev);
5580
5581 return _e1000_init(hw, plat->enetaddr);
5582}
5583
5584static void e1000_eth_stop(struct udevice *dev)
5585{
5586 struct e1000_hw *hw = dev_get_priv(dev);
5587
5588 _e1000_disable(hw);
5589}
5590
5591static int e1000_eth_send(struct udevice *dev, void *packet, int length)
5592{
5593 struct e1000_hw *hw = dev_get_priv(dev);
5594 int ret;
5595
5596 ret = _e1000_transmit(hw, packet, length);
5597
5598 return ret ? 0 : -ETIMEDOUT;
5599}
5600
5601static int e1000_eth_recv(struct udevice *dev, int flags, uchar **packetp)
5602{
5603 struct e1000_hw *hw = dev_get_priv(dev);
5604 int len;
5605
5606 len = _e1000_poll(hw);
5607 if (len)
5608 *packetp = packet;
5609
5610 return len ? len : -EAGAIN;
5611}
5612
5613static int e1000_free_pkt(struct udevice *dev, uchar *packet, int length)
5614{
5615 struct e1000_hw *hw = dev_get_priv(dev);
5616
5617 fill_rx(hw);
5618
5619 return 0;
5620}
5621
5622static int e1000_eth_probe(struct udevice *dev)
5623{
5624 struct eth_pdata *plat = dev_get_platdata(dev);
5625 struct e1000_hw *hw = dev_get_priv(dev);
5626 int ret;
5627
5628 hw->name = dev->name;
Simon Glass21ccce12015-11-29 13:17:47 -07005629 ret = e1000_init_one(hw, trailing_strtol(dev->name),
Bin Meng81dab9a2016-02-02 05:58:01 -08005630 dev, plat->enetaddr);
Simon Glassc6d80a12015-08-19 09:33:40 -06005631 if (ret < 0) {
5632 printf(pr_fmt("failed to initialize card: %d\n"), ret);
5633 return ret;
5634 }
5635
5636 return 0;
5637}
5638
5639static int e1000_eth_bind(struct udevice *dev)
5640{
5641 char name[20];
5642
5643 /*
5644 * A simple way to number the devices. When device tree is used this
5645 * is unnecessary, but when the device is just discovered on the PCI
5646 * bus we need a name. We could instead have the uclass figure out
5647 * which devices are different and number them.
5648 */
5649 e1000_name(name, num_cards++);
5650
5651 return device_set_name(dev, name);
5652}
5653
5654static const struct eth_ops e1000_eth_ops = {
5655 .start = e1000_eth_start,
5656 .send = e1000_eth_send,
5657 .recv = e1000_eth_recv,
5658 .stop = e1000_eth_stop,
5659 .free_pkt = e1000_free_pkt,
5660};
5661
5662static const struct udevice_id e1000_eth_ids[] = {
5663 { .compatible = "intel,e1000" },
5664 { }
5665};
5666
5667U_BOOT_DRIVER(eth_e1000) = {
5668 .name = "eth_e1000",
5669 .id = UCLASS_ETH,
5670 .of_match = e1000_eth_ids,
5671 .bind = e1000_eth_bind,
5672 .probe = e1000_eth_probe,
5673 .ops = &e1000_eth_ops,
5674 .priv_auto_alloc_size = sizeof(struct e1000_hw),
5675 .platdata_auto_alloc_size = sizeof(struct eth_pdata),
5676};
5677
5678U_BOOT_PCI_DEVICE(eth_e1000, e1000_supported);
5679#endif