include/configs/mcc200.h

/*
 * (C) Copyright 2006-2008
 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 * (easy to change)
 */

#define CONFIG_MPC5200
#define CONFIG_MCC200		1	/* MCC200 board */

/*
 * Valid values for CONFIG_SYS_TEXT_BASE are:
 * 0xFC000000	boot low (standard configuration)
 * 0xFFF00000	boot high
 * 0x00100000	boot from RAM (for testing only)
 */
#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE	0xFC000000
#endif

#define CONFIG_SYS_MPC5XXX_CLKIN	33000000 /* ... running at 33MHz		*/

#define CONFIG_MISC_INIT_R

#define CONFIG_HIGH_BATS	1	/* High BATs supported			*/

/*
 * Serial console configuration
 *
 *  To select console on the one of 8 external UARTs,
 * define CONFIG_QUART_CONSOLE as 1, 2, 3, or 4 for the first Quad UART,
 * or as 5, 6, 7, or 8 for the second Quad UART.
 * COM11, COM12, COM13, COM14 are located on the second Quad UART.
 *
 *  CONFIG_PSC_CONSOLE must be undefined in this case.
 */
#if !defined(CONFIG_PRS200)
/* MCC200 configuration: */
#ifdef CONFIG_CONSOLE_COM12
#define CONFIG_QUART_CONSOLE	6	/* console is on UARTF of QUART2	*/
#else
#define CONFIG_QUART_CONSOLE	8	/* console is on UARTH of QUART2	*/
#endif
#else
/* PRS200 configuration: */
#undef CONFIG_QUART_CONSOLE
#endif /* CONFIG_PRS200 */
/*
 *  To select console on PSC1, define CONFIG_PSC_CONSOLE as 1
 * and undefine CONFIG_QUART_CONSOLE.
 */
#if !defined(CONFIG_PRS200)
/* MCC200 configuration: */
#define CONFIG_PSC_CONSOLE	1	/* PSC1 may be COM */
#define CONFIG_PSC_CONSOLE2	2	/* PSC2 is PSoC */
#else
/* PRS200 configuration: */
#define CONFIG_PSC_CONSOLE	1	/* console is on PSC1		*/
#endif
#define CONFIG_BAUDRATE		115200
#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }

#define CONFIG_MII		1

#define CONFIG_DOS_PARTITION

/* USB */
#define CONFIG_USB_OHCI
#define CONFIG_USB_STORAGE
/* automatic software updates (see board/mcc200/auto_update.c) */
#define CONFIG_AUTO_UPDATE 1


/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME


/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_BEDBUG
#define CONFIG_CMD_FAT
#define CONFIG_CMD_I2C
#define CONFIG_CMD_USB

#undef	CONFIG_CMD_NET
#undef	CONFIG_CMD_NFS

/*
 * Autobooting
 */
#define CONFIG_BOOTDELAY	1	/* autoboot after 1 second */

#define CONFIG_PREBOOT	"echo;"	\
	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
	"echo"

#undef	CONFIG_BOOTARGS

#ifdef CONFIG_PRS200
# define CONFIG_SYS__BOARDNAME		"prs200"
# define CONFIG_SYS__LINUX_CONSOLE	"ttyS0"
#else
# define CONFIG_SYS__BOARDNAME		"mcc200"
# define CONFIG_SYS__LINUX_CONSOLE	"ttyEU5"
#endif

/* Network */
#define CONFIG_ETHADDR	00:17:17:ff:00:00
#define CONFIG_IPADDR	10.76.9.29
#define CONFIG_SERVERIP	10.76.9.1

#include <version.h> /* For U-Boot version */

#define CONFIG_EXTRA_ENV_SETTINGS					\
	"ubootver=" U_BOOT_VERSION "\0"					\
	"netdev=eth0\0"							\
	"hostname=" CONFIG_SYS__BOARDNAME "\0"				\
	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
		"nfsroot=${serverip}:${rootpath}\0"			\
	"ramargs=setenv bootargs root=/dev/mtdblock2 "			\
		"rootfstype=cramfs\0"					\
	"addip=setenv bootargs ${bootargs} "				\
		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
		":${hostname}:${netdev}:off panic=1\0"			\
	"addcons=setenv bootargs ${bootargs} "				\
		"console=${console},${baudrate} "			\
		"ubootver=${ubootver} board=${board}\0"			\
	"flash_nfs=run nfsargs addip addcons;"				\
		"bootm ${kernel_addr}\0"				\
	"flash_self=run ramargs addip addcons;"				\
		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
	"net_nfs=tftp 200000 ${bootfile};"				\
		"run nfsargs addip addcons;bootm\0"			\
	"console=" CONFIG_SYS__LINUX_CONSOLE "\0"				\
	"rootpath=/opt/eldk/ppc_6xx\0"					\
	"bootfile=/tftpboot/" CONFIG_SYS__BOARDNAME "/uImage\0"		\
	"load=tftp 200000 /tftpboot/" CONFIG_SYS__BOARDNAME "/u-boot.bin\0"	\
	"text_base=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"		\
	"kernel_addr=0xFC0C0000\0"					\
	"update=protect off ${text_base} +${filesize};"			\
		"era ${text_base} +${filesize};"			\
		"cp.b 200000 ${text_base} ${filesize}\0"		\
	"unlock=yes\0"							\
	""

#define CONFIG_BOOTCOMMAND	"run flash_self"

#define CONFIG_SYS_HUSH_PARSER		1	/* use "hush" command parser	*/

/*
 * IPB Bus clocking configuration.
 */
#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK		/* define for 133MHz speed */

/*
 * I2C configuration
 */
#define CONFIG_HARD_I2C		1	/* I2C with hardware support */
#define CONFIG_SYS_I2C_MODULE		2	/* Select I2C module #1 or #2 */

#define CONFIG_SYS_I2C_SPEED		100000 /* 100 kHz */
#define CONFIG_SYS_I2C_SLAVE		0x7F

/*
 * Flash configuration (8,16 or 32 MB)
 * TEXT base always at 0xFFF00000
 * ENV_ADDR always at  0xFFF40000
 * FLASH_BASE at 0xFC000000 for 64 MB (only 32MB are supported, not enough addr lines!!!)
 *		 0xFE000000 for 32 MB
 *		 0xFF000000 for 16 MB
 *		 0xFF800000 for  8 MB
 */
#define CONFIG_SYS_FLASH_BASE		0xfc000000
#define CONFIG_SYS_FLASH_SIZE		0x04000000

#define CONFIG_SYS_FLASH_CFI				/* The flash is CFI compatible	*/
#define CONFIG_FLASH_CFI_DRIVER			/* Use common CFI driver	*/

#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }

#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
#define CONFIG_SYS_MAX_FLASH_SECT	512	/* max number of sectors on one chip	*/

#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
#define CONFIG_SYS_FLASH_PROTECTION	1	/* hardware flash protection		*/

#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/

#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
#define CONFIG_SYS_FLASH_QUIET_TEST	1	/* don't warn upon unknown flash	*/

#define CONFIG_ENV_IS_IN_FLASH	1	/* use FLASH for environment vars	*/

#define CONFIG_ENV_SECT_SIZE	0x40000	/* size of one complete sector	*/
#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
#define	CONFIG_ENV_SIZE		0x2000	/* Total Size of Environment Sector	*/

/* Address and size of Redundant Environment Sector	*/
#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)

#define CONFIG_ENV_OVERWRITE	1	/* allow modification of vendor params */

#if CONFIG_SYS_TEXT_BASE == CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LOWBOOT	1
#endif

/*
 * Memory map
 */
#define CONFIG_SYS_MBAR		0xf0000000
#define CONFIG_SYS_SDRAM_BASE		0x00000000
#define CONFIG_SYS_DEFAULT_MBAR	0x80000000

/* Use SRAM until RAM will be available */
#define CONFIG_SYS_INIT_RAM_ADDR	MPC5XXX_SRAM
#define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_SIZE	/* Size of used area in DPRAM */


#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#   define CONFIG_SYS_RAMBOOT		1
#endif

#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
#define CONFIG_SYS_MALLOC_LEN		(512 << 10)	/* Reserve 512 kB for malloc()	*/
#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */

/*
 * Ethernet configuration
 */
/* #define CONFIG_MPC5xxx_FEC	1 */
/* #define CONFIG_MPC5xxx_FEC_MII100 */
/*
 * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
 */
/* #define CONFIG_MPC5xxx_FEC_MII10 */
#define CONFIG_PHY_ADDR		1

/*
 * LCD Splash Screen
 */
#if !defined(CONFIG_PRS200)
#define CONFIG_LCD		1
#define CONFIG_PROGRESSBAR 1
#endif

#if defined(CONFIG_LCD)
#define CONFIG_SPLASH_SCREEN	1
#define CONFIG_SYS_CONSOLE_IS_IN_ENV	1
#define LCD_BPP			LCD_MONOCHROME
#endif

/*
 * GPIO configuration
 */
/* 0x10000004 = 32MB SDRAM */
/* 0x90000004 = 64MB SDRAM */
#if defined(CONFIG_LCD)
/* set PSC2 in UART mode */
#define CONFIG_SYS_GPS_PORT_CONFIG	0x00000044
#else
#define CONFIG_SYS_GPS_PORT_CONFIG	0x00000004
#endif

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size	*/
#else
#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size	*/
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size	*/
#define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/

#define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on	*/
#define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM	*/

#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */

#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC5xxx CPUs			*/
#if defined(CONFIG_CMD_KGDB)
#  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
#endif

/*
 * Various low-level settings
 */
#define CONFIG_SYS_HID0_INIT		HID0_ICE | HID0_ICFI
#define CONFIG_SYS_HID0_FINAL		HID0_ICE

#define CONFIG_SYS_BOOTCS_START	CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_BOOTCS_SIZE		CONFIG_SYS_FLASH_SIZE
#define CONFIG_SYS_BOOTCS_CFG		0x0004fb00
#define CONFIG_SYS_CS0_START		CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_CS0_SIZE		CONFIG_SYS_FLASH_SIZE

/* Quad UART @0x80000000 (MBAR is relocated to 0xF0000000) */
#define CONFIG_SYS_CS2_START		0x80000000
#define CONFIG_SYS_CS2_SIZE		0x00001000
#define CONFIG_SYS_CS2_CFG		0x1d300

/* Second Quad UART @0x80010000 */
#define CONFIG_SYS_CS1_START		0x80010000
#define CONFIG_SYS_CS1_SIZE		0x00001000
#define CONFIG_SYS_CS1_CFG		0x1d300

/* Leica - build revision resistors */
/*
#define CONFIG_SYS_CS3_START		0x80020000
#define CONFIG_SYS_CS3_SIZE		0x00000004
#define CONFIG_SYS_CS3_CFG		0x1d300
*/

/*
 *  Select one of quarts as a default
 * console. If undefined - PSC console
 * wil be default
 */
#define CONFIG_SYS_CS_BURST		0x00000000
#define CONFIG_SYS_CS_DEADCYCLE	0x33333333

#define CONFIG_SYS_RESET_ADDRESS	0xff000000

/*
 * QUART Expanders support
 */
#if defined(CONFIG_QUART_CONSOLE)
/*
 * We'll use NS16550 chip routines,
 */
#define CONFIG_SYS_NS16550		1
#define CONFIG_SYS_NS16550_SERIAL	1
#define CONFIG_CONS_INDEX	1
/*
 *  To achieve necessary offset on SC16C554
 * A0-A2 (register select) pins with NS16550
 * functions (in struct NS16550), REG_SIZE
 * should be 4, because A0-A2 pins are connected
 * to DA2-DA4 address bus lines.
 */
#define CONFIG_SYS_NS16550_REG_SIZE	4
/*
 * LocalPlus Bus already inited in cpu_init_f(),
 * so can work with QUART's chip selects.
 * One of four SC16C554 UARTs is selected with
 * A3-A4 (DA5-DA6) lines.
 */
#if (CONFIG_QUART_CONSOLE > 0) && (CONFIG_QUART_CONSOLE < 5) && !defined(CONFIG_PRS200)
#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CS2_START | (CONFIG_QUART_CONSOLE - 1)<<5)
#elif (CONFIG_QUART_CONSOLE > 4) && (CONFIG_QUART_CONSOLE < 9)
#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CS1_START | (CONFIG_QUART_CONSOLE - 5)<<5)
#else
#error "Wrong QUART expander number."
#endif

/*
 * SC16C554 chip's external crystal oscillator frequency
 * is 7.3728 MHz
 */
#define CONFIG_SYS_NS16550_CLK		7372800
#endif /* CONFIG_QUART_CONSOLE */
/*-----------------------------------------------------------------------
 * USB stuff
 *-----------------------------------------------------------------------
 */
#define CONFIG_USB_CLOCK	0x0001BBBB
#define CONFIG_USB_CONFIG	0x00005000

#define CONFIG_AUTOBOOT_KEYED		/* use key strings to stop autoboot	*/
#define CONFIG_AUTOBOOT_STOP_STR	"432"
#define CONFIG_SILENT_CONSOLE	1

#endif /* __CONFIG_H */